Search results

REPAIRING aircraft for Imperial Airways, led, at the beginning of the war, to the setting up of a repair organization with its headquarters at Rochester. All the work carried out was category ‘AC’ (repairable on site by contractors' party), except later when the Windermere factory and Short & Harland, Belfast, started to deal with category ‘B’ (repairable by contractor at the firm). At Windermere work was mainly large modifications or major overhauls. Short & Harland organized a separate repair department which dealt with all types of aircraft in Northern Ireland.

THE policy and organization of the Avro Repair Group was based upon intelligent anticipation—anticipation of the many and varied types of damage that might be expectedl anticipation of quantities, and anticipation of facilities to deal with all contingencies. The central depot at Bracebridge Heath, Lincoln, developed from an ex‐1914–18 war hangar to an establishment employing nearly 3,000 men and forming the hub of an organization that embraced many stations and subcontractors' works, civilian out‐working parties, of A. V. Roe personnel, effected a high proportion of major repairs to Lancaster, York and Anson aircraft; such parties were stationed all over the British Isles and were supplemented by a fleet of some seventy mobile workshops.

This study aims to investigate lattice Boltzmann (LB) simulation of the fluid flow and heat transfer characteristics of a heated porous elliptic cylinder in uniform flow based on the two-domain scheme. In the present research, the effect of axis ratio (1 ≤ AR ≤ 2), Reynolds number (5 ≤ Re ≤ 40) and Darcy number (10⁻⁴ ≤ Da ≤ 10⁻²) are studied.

To perform the LB simulation based on the two-domain scheme, the nonequilibrium extrapolation method is modified to model the heat transfer interfacial conditions required at the curved interface.

The results show that the axis ratio as well as Reynolds and Darcy numbers significantly affect the fluid flow and heat transfer characteristics of the porous elliptic cylinder. It is shown that for AR > 1, the phenomenon of detached recirculating zone occurs at much higher Darcy numbers compared with the case of the porous circular cylinder (AR = 1). The results show that the location of maximum temperature within the cylinder moves downstream when the Reynolds number, Darcy number and axis ratio increase. It is also concluded that the average Nusselt number of a porous elliptic cylinder is always lower than that of a porous circular cylinder.

The LB simulation of forced convection from a porous cylinder in uniform flow with a curved interface based on the two-domain scheme has not been studied yet.

The purpose of this study is to propose an isogeometric analysis (IGA) approach for solving the Reynolds equation in textured piston ring cylinder liner (PRCL) contacts.

The texture region is accurately and conveniently expressed by non-uniform rational B-splines (NURBS) besides hydrodynamic pressure and the oil film density ratio is represented in this mathematical form. A quadratic programming method combined with a Lagrange multiplier method is developed to address the cavitation issue.

The comparison with the results solved by an analytical method has verified the effectiveness of the proposed approach. In the study of the PRCL contact with two-dimensional circular dimple textures, the solution of the IGA approach shows high smoothness and accuracy, and it well satisfies the complementarity condition in the case of cavitation presence.

This paper proposes an IGA approach for solving the Reynolds equation in textured PRCL contacts. Its novelty is reflected in three aspects. First, NURBS functions are simultaneously used to express the solution domain, texture shape, hydrodynamic pressure and oil density ratio. Second, the streamline upwind/Petrov–Galerkin method is adopted to create a weak form for the Reynolds equation that takes the oil density ratio as a first-order unknown variable. Third, a quadratic programming approach is developed to impose the complementarity conditions between the hydrodynamic pressure and the oil density ratio.

This paper aims to derive a reduced-order model for the heat transfer across the interface between a millimetric thermocapillary liquid bridge from silicone oil and the surrounding ambient gas.

Numerical solutions for the two-fluid model are computed covering a wide parametric space, making a total of 2,800 numerical flow simulations. Based on the computed data, a reduced single-fluid model for the liquid phase is devised, in which the heat transfer between the liquid and the gas is modeled by Newton’s heat transfer law, albeit with a space-dependent Biot function Bi(z), instead of a constant Biot number Bi.

An explicit robust fit of Bi(z) is obtained covering the whole range of parameters considered. The single-fluid model together with the Biot function derived yields very accurate results at much lesser computational cost than the corresponding two-phase fully-coupled simulation required for the two-fluid model.

Using this novel Biot function approach instead of a constant Biot number, the critical Reynolds number can be predicted much more accurately within single-phase linear stability solvers.

The Biot function for thermocapillary liquid bridges is derived from the full multiphase problem by a robust multi-stage fit procedure. The derived Biot function reproduces very well the theoretical boundary layer scalings.

Piston ring dynamic problem plays an important role in the lubricant characteristics of a reciprocating engine, which lead to engine wear and the increased consumption of lubricating oil. A cavitation analysis of the piston ring lubrication with two-dimensional Reynolds equation has rarely been reported owing to the complex working condition. The purpose of this study is to establish a precise model that can provide guidance for the design of the piston ring.

In this paper, a cavitation model and its effect on the piston ring lubrication was studied in a simulation program based on the mass-conserving theory which is solved by means of the Newton–Raphson method. In this study, some models such as mixed lubrication, asperity contact, blow-by/blow-back flow and cavitation have been coupled with the lubrication model.

The established model has been compared with the traditional model that deals with cavitation by using the Reynolds boundary condition algorithm. The cavitation zone, pressure distribution and density distribution between the piston ring and the cylinder have also been predicted. Studies of the changing trend for the pressure distribution and the cavitation zone at few typical crank angles have been listed to illustrate the cavitation changing rule. The analysis of the results indicates that the developed simulation model can adequately illustrate the lubrication problem of the piston ring system. All the analyses will provide guidance for the oil film rupture and the reformation process.

A two-dimensional cavitation model based on the mass-conserving theory has been built. The cavitation-forming and -developing process for the piston ring–liner lubrication has been studied. Non-cavitation occurs in the vicinity of top dead center and bottom dead center. The non-cavitation period will be longer in the vicinity of 360° of crank angle. The density distribution in the cavitation zone can be obtained.

Information and communications technology (ICT) offers enormous opportunities for individuals, businesses and society. The application of ICT is equally important to economic and non-economic activities. Researchers have increasingly focused on the adoption and use of ICT by small and medium enterprises (SMEs) as the economic development of a country is largely dependent on them. Following the success of ICT utilisation in SMEs in developed countries, many developing countries are looking to utilise the potential of the technology to develop SMEs. Past studies have shown that the contribution of ICT to the performance of SMEs is not clear and certain. Thus, it is crucial to determine the effectiveness of ICT in generating firm performance since this has implications for SMEs’ expenditure on the technology. This research examines the diffusion of ICT among SMEs with respect to the typical stages from innovation adoption to post-adoption, by analysing the actual usage of ICT and value creation. The mediating effects of integration and utilisation on SME performance are also studied. Grounded in the innovation diffusion literature, institutional theory and resource-based theory, this study has developed a comprehensive integrated research model focused on the research objectives. Following a positivist research paradigm, this study employs a mixed-method research approach. A preliminary conceptual framework is developed through an extensive literature review and is refined by results from an in-depth field study. During the field study, a total of 11 SME owners or decision-makers were interviewed. The recorded interviews were transcribed and analysed using NVivo 10 to refine the model to develop the research hypotheses. The final research model is composed of 30 first-order and five higher-order constructs which involve both reflective and formative measures. Partial least squares-based structural equation modelling (PLS-SEM) is employed to test the theoretical model with a cross-sectional data set of 282 SMEs in Bangladesh. Survey data were collected using a structured questionnaire issued to SMEs selected by applying a stratified random sampling technique. The structural equation modelling utilises a two-step procedure of data analysis. Prior to estimating the structural model, the measurement model is examined for construct validity of the study variables (i.e. convergent and discriminant validity).

The estimates show cognitive evaluation as an important antecedent for expectation which is shaped primarily by the entrepreneurs’ beliefs (perception) and also influenced by the owners’ innovativeness and culture. Culture further influences expectation. The study finds that facilitating condition, environmental pressure and country readiness are important antecedents of expectation and ICT use. The results also reveal that integration and the degree of ICT utilisation significantly affect SMEs’ performance. Surprisingly, the findings do not reveal any significant impact of ICT usage on performance which apparently suggests the possibility of the ICT productivity paradox. However, the analysis finally proves the non-existence of the paradox by demonstrating the mediating role of ICT integration and degree of utilisation explain the influence of information technology (IT) usage on firm performance which is consistent with the resource-based theory. The results suggest that the use of ICT can enhance SMEs’ performance if the technology is integrated and properly utilised. SME owners or managers, interested stakeholders and policy makers may follow the study’s outcomes and focus on ICT integration and degree of utilisation with a view to attaining superior organisational performance.

This study urges concerned business enterprises and government to look at the environmental and cultural factors with a view to achieving ICT usage success in terms of enhanced firm performance. In particular, improving organisational practices and procedures by eliminating the traditional power distance inside organisations and implementing necessary rules and regulations are important actions for managing environmental and cultural uncertainties. The application of a Bengali user interface may help to ensure the productivity of ICT use by SMEs in Bangladesh. Establishing a favourable national technology infrastructure and legal environment may contribute positively to improving the overall situation. This study also suggests some changes and modifications in the country’s existing policies and strategies. The government and policy makers should undertake mass promotional programs to disseminate information about the various uses of computers and their contribution in developing better organisational performance. Organising specialised training programs for SME capacity building may succeed in attaining the motivation for SMEs to use ICT. Ensuring easy access to the technology by providing loans, grants and subsidies is important. Various stakeholders, partners and related organisations should come forward to support government policies and priorities in order to ensure the productive use of ICT among SMEs which finally will help to foster Bangladesh’s economic development.

Investigates the differences in protocols between arbitral tribunals and courts, with particular emphasis on US, Greek and English law. Gives examples of each country and its way of using the law in specific circumstances, and shows the variations therein. Sums up that arbitration is much the better way to gok as it avoids delays and expenses, plus the vexation/frustration of normal litigation. Concludes that the US and Greek constitutions and common law tradition in England appear to allow involved parties to choose their own judge, who can thus be an arbitrator. Discusses e‐commerce and speculates on this for the future.

The purpose of this paper is to study the laminar boundary layer flow between a stationary nonporous disk and a porous rotating disk, both being immersed in large amount of fluid.

The governing nonlinear momentum equations in cylindrical polar coordinates together with relevant boundary conditions are reduced to a system of coupled nonlinear ordinary differential equations (NODEs) using similarity transformations. The resulting coupled NODEs are solved using computer-extended series solution and homotopy analysis method.

The analytical solutions are explicitly expressed in terms of recurrence relation for determining the universal coefficients. The nature and location of singularity which restricts the convergence of series is analyzed by using Domb–Sykes plot. Reversion of series is used for the improvement of series. The region of validity of series is extended for much larger values of Reynolds number (R), i.e. R = 6 to 15.

The resulting solutions are compared with earlier works in the literature and are found to be in good agreement.