Search results

This paper aims to derive a reduced-order model for the heat transfer across the interface between a millimetric thermocapillary liquid bridge from silicone oil and the surrounding ambient gas.

Numerical solutions for the two-fluid model are computed covering a wide parametric space, making a total of 2,800 numerical flow simulations. Based on the computed data, a reduced single-fluid model for the liquid phase is devised, in which the heat transfer between the liquid and the gas is modeled by Newton’s heat transfer law, albeit with a space-dependent Biot function Bi(z), instead of a constant Biot number Bi.

An explicit robust fit of Bi(z) is obtained covering the whole range of parameters considered. The single-fluid model together with the Biot function derived yields very accurate results at much lesser computational cost than the corresponding two-phase fully-coupled simulation required for the two-fluid model.

Using this novel Biot function approach instead of a constant Biot number, the critical Reynolds number can be predicted much more accurately within single-phase linear stability solvers.

The Biot function for thermocapillary liquid bridges is derived from the full multiphase problem by a robust multi-stage fit procedure. The derived Biot function reproduces very well the theoretical boundary layer scalings.

The purpose of this paper is to address the heat and mass transfer effects in three-dimensional flow of Maxwell fluid over a stretching surface with convective boundary conditions. Mass transfer is considered in the presence of first order chemical reaction. Conservation laws of energy and concentration are based upon the Soret and Dufour effects. Convergent series solutions to the resulting non-linear problems are developed. Effects of Biot and Deborah numbers on the Sherwood number are decreasing. Local Nusselt reduces with an increase in Eckert numbers. It is also interesting to note further that variations of Prandtl and Biot numbers on the Nusselt number are increasing while Sherwood number decreases with an increase in Prandtl number.

The involved partial differential systems are reduced to the ordinary differential systems using appropriate transformations. Series solutions by homotopy analysis method are constructed and analyzed. Graphical results are presented and examined in detail.

It is found that roles of Deborah and Biot parameters on the Nusselt number are opposite. However, the Sherwood number is qualitative similar for both Biot and Deborah numbers. It is also interesting to note further that variations of Prandtl and Biot numbers on the Nusselt and Sherwood numbers are similar.

The purpose of present communication is to investigate the three-dimensional flow of Maxwell fluid over a stretching surface with convective condition. Analysis has been carried out in the presence of mass transfer with first order chemical reaction and Soret and Dufour effects.

A numerical study has been made to investigate the effect of internal heating and precursory cooling during quenching of an infinite tube. The finite difference solution gives the quench front temperature as a function of various model parameters such as Peclet number, Biot number and dimensionless heat flux. The parametric dependence of the rewetting rate is obtained by the condition that the surface can only be wetted when its temperature is below the quench front temperature. Also, the critical heat flux is obtained by setting Peclet number equal to zero, which gives the minimum heat flux required to prevent the hot surface being rewetted. The numerical model is validated by comparing the results with known closed form solutions.

This paper aims to explore the double diffusive magneto-hydrodynamic (MHD) squeezed flow of (Cu–water) nanofluid between two analogous plates filled with Darcy porous material in existence of chemical reaction and external magnetic field.

The governing nonlinear equations are transformed into ordinary differential equations by means of similarity transforms, and the coupled mass and heat transference equations are resolved analytically with the application of differential transform method (DTM). The effects of different relevant parameters on velocity, temperature and concentration, including the squeeze number, magnetic parameter, Biot number, Darcy number and chemical reaction parameter, are illustrated with figures. In addition, for various parameters, the local skin friction coefficient, local Nusselt number and local Sherwood number are computed and are graphically displayed.

It is observed that the squeeze number has a direct relationship with Sherwood number and an inverse relationship with skin friction as Biot number increases. With enhanced Biot numbers, the temperature value increases during both squeeze and non-squeeze moments, but the temperature values are higher for squeeze moments compared to the other case.

This research has potential applications in various large-scale enterprises that might benefit from increased productivity.

The results are useful to thermal science community.

Unique and valuable insights are provided by studying the impact of chemical reaction on double diffusive MHD squeezing copper–water nanofluid flow between parallel plates filled with porous medium. In addition, this research has potential applications in various large-scale enterprises that might benefit from increased productivity.

This study aims to expose the flow phenomena and entropy generation during a; magnetohydrodynamic (MHD) Poiseuille flow of water-based nanofluids (NFs) in a porous channel subject to hydrodynamic slip and convective heating boundary conditions. The flow caused by the uniform pressure; gradient between infinite parallel plates is considered steady and fully developed. The nanoparticles; namely, copper, alumina and titanium oxide are taken with pure water as the base fluid. Viscous dissipation and Joule heating impacts are also incorporated in this investigation.

The reduced governing equations are solved analytically in closed form. The physical insights of noteworthy parameters on the important flow quantities are demonstrated through graphs and analyzed elaborately. The thermodynamic analysis is performed by calculating entropy generation; rate and Bejan number. A graphical comparison between solutions corresponding to NFs and regular fluid in the channel is also provided.

The analysis of the results divulges that entropy generation minimization can be achieved by an appropriate combination of the geometrical and physical parameters of thermomechanical systems. It is reported that ascent in magnetic parameter number declines the velocity profiles, while the inverse pattern is witnessed with augmentation in hydrodynamic slip parameters. The temperature dissemination declines with the growth of Biot numbers. It is perceived that the entropy generation rate lessens with an upgrade in magnetic parameter, whereas the reverse trend of Bejan number is perceived with expansion in magnetic parameter and Biot number. The important contribution of the result is that the entropy generation rate is controlled with an appropriate composition of thermo-physical parameter values. Moreover, in the presence of a magnetic field and suction/injection at the channel walls, the shear stresses at the channel walls are reduced about two times.

In various industrial applications, minimizing entropy generation plays a significant role. Miniaturization of entropy is the utilization of the energy of thermal devices such as micro heat exchangers, micromixers, micropumps and cooling microelectromechanical devices.

An attentive review of the literature discloses that quite a few studies have been conducted on entropy generation analysis of a fully developed MHD Poiseuille flow of NFs through a permeable channel subject to the velocity slip and convective heating conditions at the walls.

The purpose of present communication is to analyze Darcy–Forchheimer flow of viscous nanofluid by curved stretchable surface. Flow in porous medium is characterized by Darcy–Forchheimer relation. Brownian diffusion and thermophoresis are considered. Convective heat and mass boundary conditions are also used at the curved stretchable surface.

The resulting nonlinear system is solved through shooting technique.

Skin friction coefficient is enhanced for larger porosity parameter and inertia coefficient while reverse trend is noticed for curvature parameter. Local Nusselt number is enhanced for higher Prandtl number and thermal Biot number, whereas the opposite trend is seen via curvature parameter, porosity parameter, inertia coefficient, thermophoresis parameter and Brownian motion parameter. Local Sherwood number is enhanced for Schmidt number, Brownian motion parameter and concentration Biot number, while reverse trend is noticed for curvature parameter, porosity parameter, inertia coefficient and thermophoresis parameter.

To the best of author’s knowledge, no such consideration has been given in the literature yet.

The purpose of this paper is to numerically investigate the hybrid nanofluid flow with the imposition of magnetohydrodynamic (MHD) and radiation effects alongside the convective boundary conditions over a permeable stretching/shrinking surface.

The mathematical model is formulated in the form of partial differential equations (PDEs) and are then transformed into the form of ordinary differential equations (ODEs) by using the similarity variables. The deriving ODEs are solved numerically by using the bvp4c solver in MATLAB software. Stability analysis also has been performed to determine the stable solution among the dual solutions obtain. For method validation purposes, a comparison of numerical results has been made with the previous studies.

The flow and the heat transfer of the fluid at the boundary layer are described through the plot of the velocity profile, temperature profile, skin friction coefficient and local Nusselt number that are presented graphically. Dual solutions are obtained, but only the first solution is stable. For the realizable solution at the shrinking surface, the proliferation of nanoparticle volume fraction (copper) and magnetic (magnetohydrodynamics) parameters can impede the boundary layer separation. Also, Biot number could enhance the temperature profile and the heat transfer rate at the shrinking surface region. The incrementation of 0.1% of Biot number has enhanced the heat transfer rate by approximately 0.1% and the incrementation of 0.5% volume fraction for copper has reduced the heat transfer rate by approximately 0.17%.

The presented model and numerical results are original and new. It can be used as a future reference for further investigation and related practical application. The main contribution of this investigation includes giving the initial prediction and providing the numerical data for the other researchers for their future reference regarding the impacts of nanoparticles volumetric concentration towards the main physical quantities of interest in the presence of magnetic and radiation parameters with the convective boundary conditions.

In heat transfer, fluids and nanoparticles can provide new innovative technologies with potential to adapt the heat transfer fluid’s thermal properties through control over particle size, shape and others. This paper aims to examine the effects of spherical and non-spherical (cylinder, disk, platelets, etc.) shapes of silver (Ag) nanoparticles on heat transfer enhancement and inherent irreversibility in hydromagnetic water base nanoliquid flow over a convectively heated stretching sheet with heat generation/absorption.

Applying suitable similarity constraints, the model partial differential equations are transformed into a set of nonlinear ordinary differential equations. Solutions are obtained analytically via optimal homotopy asymptotic method (OHAM) and numerically via shooting technique coupled with the Runge-Kutta-Fehlberg (RK-F) method.

The impact of Ag nanoparticle’s shape along with other germane factors, such as Biot number, magnetic field, solid volume fraction and heat source/sink on velocity and thermal profiles, Nusselt number, skin friction coefficient, heat transfer enhancement, rate of entropy generation and irreversibility ratio, are scrutinized via graphical simulations and discussed. This study revealed that cylindrical shape Ag nanoparticles generate high entropy and fluid friction irreversibility, whereas disk shape Ag nanoparticles exhibit high transfer enhancement rate. Moreover, a boost in magnetic field intensity, volume-fraction parameter and Biot number enhances the thermal boundary layer thickness.

The main objective of this work is to examine the different Ag nanoparticles shape effects on the heat transfer enhancement and inherent irreversibility owing to hydromagnetic nanoliquid flow past a convectively heated stretching sheet with heat source/sink, which has not been yet studied. It is hope that this study will bridge the gap in the present literature and serve as impetus to scholars, engineers and industries for more exploration in this direction. The intrinsic nonlinearity of the model equations precludes its exact solution; hence, OHAM and shooting technique coupled with the RK-F method have been used to numerically tackle the problem. Pertinent results are discussed quantitatively and displayed graphically and in tabular form.

The purpose of this study is to examine the Darcy–Forchheimer flow of viscous nanoliquid because of a rotating disk. Thermophoretic diffusion and random motion aspects are retained. Heat and mass transfer features are analyzed through convective conditions.

The governing systems are solved numerically by the shooting technique.

Higher porosity parameter and Forchheimer number Fr depict similar trend for both velocity profiles f' and g. Both temperature and concentration profiles show increasing behavior for higher Forchheimer number Fr. An increase in Prandtl number Pr corresponds to lower temperature profile, while opposite trend is noticed for thermal Biot number. Larger concentration Biot number exhibits increasing behavior for both concentration and its associated layer thickness.

To the best of the author’s knowledge, no such consideration has been given in the literature yet.

Microfluidics is one of the interesting areas of the research in thermal and engineering fields due to its wide range of applications in a variety of heat transport problems such as micromixers, micropumps, cooling systems for microelectromechanical systems (MEMS) micro heat exchangers, etc. Lower cost with better thermal performance is the main objective of these devices. Therefore, in this study, the entropy generation in an electrically conducting Casson fluid flow through an inclined microchannel with hydraulic slip and the convective condition hves been numerically investigated. Aspects of viscous dissipation, natural convection, joule heating, magnetic field and uniform heat source/sink are used

Suitable non-dimensional variables are used to reduce the non-linear system of ordinary differential equations, and then this system is solved numerically using Runge-Kutta-Fehlberg fourth fifth order method along with shooting technique. The obtained numerical solutions of the fluid velocity and temperature are used to characterize the entropy generation and Bejan number. Also, the Nusselt number and skin friction coefficient for various values of parameters are examined in detail through graphs. The obtained present results are compared with the existing one which is perfectly found to be in good agreement.

It is established that the production of the entropy can be improved with the aspects of joule heating, viscous dissipation and internal heat source/sink. The entropy generation enhances for increasing values of Casson Parameter (β) and Biot number (Bi). Furthermore, it is interestingly noticed that the enhancement of Reynolds number and uniform heat source/sink shows the dual behaviour of the entropy generation due to significant influence of the viscous forces in the region close to the channel walls. It was observed that increasing behaviour of the heat transfer rate for enhancement values of the Eckert number and heat source/sink ratio parameter and the drag force are retarded with higher estimations of Reynolds number.

Entropy generation analysis on MHD Casson fluid flow through an inclined microchannel with the aspects of convective, Joule heating, viscous dissipation, magnetism, hydraulic slip and internal heat source/sink has been numerically investigated.