Search results

This paper aims to study the structural, electrical and microwave properties of (Sr_0.6Ca_0.4) (Co_yMn_1−y) O₃ (0.2 ≤ y ≤ 1.0) thick-film ceramics.

The thick films of (Sr_0.6Ca_0.4) (Co_yMn_1−y) O₃ (0.2 ≤ y ≤ 1.0) on the alumina substrate have been delineated using screen printing technique. The structural analysis was carried out using an X-ray diffraction method and scanning electron microscopy. The direct current (DC) electrical resistivity is measured using a two-probe method. Microwave absorption was studied in the 8-18 GHz frequency range by using the Waveguide Reflectometer Method. The permittivity and permeability in the 8-18 GHz frequency range were measured by using Voltage Standing Wave Ratio slotted section method.

The thick films have orthorhombic perovskite structure with dominant (020) plane. By using first-principle calculation method, theoretical and experimental lattice parameter and cell volume of (Sr_0.6Ca_0.4) (Co_yMn_1−y) O₃ are matched with each other. The cobalt content changes the morphology from plates to needles. The DC electrical resistivity increases with increase in Co content and decreases with increase in temperature. (Sr_0.6Ca_0.4) (Co_yMn_1−y) O₃ thick film shows 75 per cent microwave absorption both in the X band and Ku band. The microwave permittivity and permeability decreases with increase in frequency and Co content.

Structural, electrical and microwave properties of (Sr_0.6Ca_0.4) (Co_yMn_1−y) O₃ (0.2 ≤ y ≤ 1.0). Thick film ceramics on alumina substrate is reported for the first time.

After working through the case, the students should be able to understand Indian political economy and the brand building process of NaMo; identify the media mix strategies used to build the brand NaMo in India; evaluate possible future growth strategies for brand NaMo; and compare and contrast brand NaMo with business brands.

Narendra Modi popularly called as NaMo was the current Prime Minister of India. He belonged to Bhartiya Janata Party (BJP) which won India’s general elections in two consecutive terms 2014 and 2019. NaMo was recognised worldwide for his prudence in leading the country to greater heights of achievement. NaMo started his political journey as the worker of BJP at a tender age. His rise in political career was akin to flagship brand overtaking the parent brand. All the steps taken in the past to position himself as a cult brand, will it fortify to NaMo’s victory in 2024 general elections? Business firms may follow NaMo’s strategies. What can the business brands emulate from NaMo to market and position themselves? Can political success be transpired to business success?

This case is designed for use in a graduate-/postgraduate-level marketing course in segments on brand management, brand expansion and the marketing strategies of a market leader. The case can also be used in a brand management course to discuss brand management models (e.g. Keller’s brand resonance pyramid and brand value chain). This case has particular application for classes that focus on brand equity, STP for any brand (segmentation, targeting and positioning) and brand value chain. The case looks in detail at the Indian political market and brand building process of NaMo and examines competitive moves since its inception. This case can be used in brand management, media management courses. The dilemma can be explained as part of a marketing course for postgraduate and executive programmes.

Teaching notes are available for educators only. Please contact your library to gain login details or email support@emeraldinsight.com to request teaching notes.

CSS 8: Marketing.

The effective, efficient and optimal design of micromixer is the need in the field of biochemical and biomedical diagnostic systems.

In this paper, multi-objective optimization of split and recombine micromixer (SRM) with different geometrical configurations is carried out. The finite element method-based three-dimensional models are prepared and analyzed using COMSOL Multiphysics 5.0 Software. Taguchi’s design of experiment (DoE), main effect plot analysis, ANOVA and grey relational analysis (GRA) method are used to find out optimum condition. The five geometrical parameters with three levels, namely, angle between inlets, pillar size, pillar shape, aspect ratio and constriction height of SRM are considered as design variables. The mixing index (MXI) and pressure drop (∆P) are considered objective functions.

The MXI is significantly influenced by pillar shape and aspect ratio, whereas the pressure drop (∆P) by constriction height. Maximum MXI (0.97) with minimum pressure drop (64,587 Pa) is the optimal conditions and obtained at 180 deg angle between inlets, 50 µm of pillar size, 1.5 of aspect ratio, 100 µm of constriction height and ellipse shape pillar cross-section, respectively.

This optimized SRM can be combined with lab-on-a-chip for biochemical and biomedical analysis.

This work is useful to obtain optimal geometry of SRM for getting efficient performance of micromixer.

The aim of this study is to examine the effect of carbonization on the surface and its influence on heavy metal removal by water hyacinth based carbon.

Dried water hyacinth stem was used as precursor to prepare carbon based adsorbent by pyrolysis method. The adsorbent proximate (ash, volatile matter and fixed carbon) and elemental (carbon hydrogen nitrogen sulfur) composition, surface area, pore size distribution, surface chemistry was examined and compared.

The results demonstrated that through carbonization in comparison to dried water hyacinth stem, it increased the surface area (from 58.46 to 328.9 m²/g), pore volume (from 0.01 to 0.07 cc/g), pore size (from 1.44 to 7.557 Å) thus enhancing heavy metal adsorption. The metal adsorption capacity of Cd, Pb and Zn was measured and analyzed through induced coupled plasma-mass spectrometer. At metal concentration of 0.1 mg/l adsorption rate for Cd, Pb and Zn was 99% due to increased large surface area, coupled with large pore size and volume. Furthermore, the adsorbent surface hydroxyl group (OH⁻) enhanced adsorption of positively charged metal ions through electrostatic forces.

It is presumed that not only adsorption with synthetic wastewater but real wastewater samples should be examined to ascertain the viability of adsorbent for commercial application.

There are little or scanty data on the effects of carbonization on water hyacinth stem based carbon and subsequent effects on heavy metal removal in effluents.

Glass is a brittle material produced from silica, which has fine material properties, Owing to its sophisticated material properties, glass has found wide application in various high-technological fields such as aviation, aerospace, communication, optics, biomedical and electronics. However, glass is known as difficult to machine material because of its tendency to brittle fracture during machining. This paper aims to investigate the effects of cutting parameters on surface quality and machining time during micro-milling of brittle glass components.

A comprehensive genetic algorithm-based optimization strategy is used for selection of process parameters such as cutting speed, feed rate and depth of cut. Effectiveness of the proposed strategy is validated by conducting micro-milling cutting experiments on soda-lime glass material.

Results showed that the generated surface quality drastically decrease with increase in the amount of removed material. Lower depth of cut and feed rate result in less amount of cracks formed on machined surface. Also, it is observed that the increase in cutting speed results in better surface quality. Having desired surface quality in shorter machining time directly reduces energy consumed during manufacturing, which is reducing environmental impact of glass parts.

The novelty of this research work lies in simultaneously considering the effects of cutting speed, feed rate, depth of cut on surface quality and machining time for micro-milling operation of brittle glass material. The model is able to find optimum process parameters for high surface quality and minimum machining time.

This study aims to investigate the behavior of vegetable oil with two additives. Base oil’s tribological qualities can be improved with the help of several additions. In the present investigation, soybean oil is served as the foundational oil due to its eco-friendliness and status as a vegetable oil with two additives, named polytetrafluoroethylene (PTFE) and molybdenum disulfide (MoS₂).

As additives, PTFE and MoS₂ are used; PTFE is renowned for its anti-friction (AF) properties, while MoS₂ is a solid lubricant with anti-wear (AW) properties. This investigation examines the synergistic impact of AF and AW additions in vegetable oil. The lubricity of the base oil is measured by using a four-ball tester, and the wear properties of the oil at different additive amounts are determined by using a universal tribometer.

PTFE (at 5 Wt.%) and MoS₂ (at 1 Wt.%) were found to improve the tribological performance of the base oil. The weld load is significantly increased when 5 Wt.% of PTFE + MoS₂ is added to the base oil.

A better tribological characteristic can be achieved by combining additives that amount to less than 1% of the base oil. In experiments with highly concentrated MoS₂, the adequate pressure improved dramatically, but the lubricant’s tribological characteristics did not.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-11-2022-0321/

The purpose of this paper is to synthesize SnO₂–ZnO hollow nanofibers, study their sensing properties and introduce an attractive candidate for formaldehyde detection in practice.

Pure and SnO₂–ZnO hollow nanofibers were synthesized by electrospinning method and characterized via X-ray diffraction, field-emission scanning electron microscopy and Fourier transform infrared spectroscopy. The formaldehyde-sensing properties were investigated.

The optimum performance was obtained at 260°C by the 14 at.% SnO₂–ZnO hollow nanofiber sensor. The sensor could detect formaldehyde down to 0.1 ppm with rapid response–recovery time (4-6 s and 7-9 s, respectively), high sensitivity, good selectivity and stability. The relationship between the sensor’s sensitivity and formaldehyde concentration suggests that the adsorbed oxygen species on the sensor’s surface is O2−. The prominent sensing properties are attributed to the one dimensional hollow nanofiber structures and the promoting effects of SnO₂.

The sensor fabricated from 14 at.% SnO₂–ZnO fibers exhibits excellent formaldehyde-sensing characteristics. It can be used for formaldehyde detection in practice.

The electrospinning method is a very simple and convenient method for fabricating hollow nanofibers and the sensing material is of low cost.

To the best of the authors’ knowledge, studies on formaldehyde sensing of SnO₂–ZnO hollow nanofibers have not been reported before.

Plasma arc cutting (PAC) is extensively applicable for cutting the materials in faster speed with better accuracy in different manufacturing industries. The cutting of sailhard steel plate plays a great challenge in plasma arc cutting process.

In this investigation, a special abrasion-resistant steel known as sailhard of 20 mm thickness plate has been cut by PAC machine. Cutting current, stand-off distance, cutting speed and gas pressure were selected as cutting parameters. The corresponding responses focused for this study are material removal rate, kerf and chamfer. L30 orthogonal array based on a central composite design (CCD) of response surface methodology (RSM) was used to design the run of the experiment. For predicting and modeling of optimal cutting conditions, a hybrid approach of desirability function-based response surface methodology (DRSM) was acquainted.

The result of this study determines that desirability index (DI) was affected significantly with the machining parameter as well as their interaction. A confirmation test was carried out to analyze the degree of effectiveness of DRSM technique.

In PAC, the selection of process parameters and effect of that parameter on the output responses is of greater value because of the selection of best cutting condition.

This study aims to solve the problems of low flow rate and low efficiency of micropumps in high-frequency applications. This micropump system was proposed to meet the requirements of 1–5 ml/min for microthrusters or drug delivery devices.

In this paper, a comprehensive analysis indicator and numerical procedure were disclosed and used to demonstrate the fluid dynamic characteristics and performance of a micropump. Accordingly, the reliability of the two-way coupling calculation was ensured through mutual verification of the real structure and the numerical system.

The research results indicate that the Polydimethylsiloxane (PDMS) microchannel can realize the contraction and expansion mechanism, allowing the fluid to generate different levels of pressure gradient during the working stroke and also enhancing the characteristics of energy consumption and storage of the flow field.

The pressure gradient between the fluid and PDMS microchannel can facilitate the improvement of the fluid backflow in a micropump. Therefore, in terms of performance improvement, the PDMS micropump increased the maximum backflow and optimum efficiency by approximately 50 and 90%, respectively.

The internal fixation plate of bone fractures by using polylactic acid (PLA) has attracted the attention of many researchers, as it is biodegradable and biocompatible to the human body. However, its brittleness has led to implant fracture. On the contrary, polypropylene carbonate (PPC), which is also biodegradable and biocompatible, has an excellent elongation at break. The purpose of this paper is to compare the PLA fixation plate with the new fixation plate made up of PLA/PPC blends by using finite element analysis (FEA).

The mandible bone from CT data set and fixation plate was designed by using the MIMICS, Amira and Solidworks softwares. Abaqus software was used for FEA of PLA/PPC fixation plate applied on the fractured mandible bone. A model of mandibular bone with a fracture in the body was subjected to incisor load. The analysis was run to determine the von Mises stress, elongation of the fixation plate and the displacement of the fractured gap of PLA/PPC blends fixation plate.

The von Mises stress predicted that all the blend compositions were safe to be used as a fixation plate since the stress values were less than the yield strength. In addition, the stress value of the fixation plate was gradually decreased up to 20 percent when the amount of PPC increased to 30 percent. This indicates that the stress shielding effect was successfully reduced. The elongation of the fixation plate was gradually increased from 11.54 to 12.55 µm as the amount of PPC in the blends increased from 0 to 30 percent, thereby illustrating that the flexibility of the fixation plate was improved by the addition of PPC. Finally, the measured displacement of the fractured gap for all compositions of PLA/PPC blends fixation plate is less than 150 µm, which proves the likely success of fracture fixation by using the PLA/PPC blends.

An optimum solution of PLA/PPC blends and another new material such as compatibilizer need to be introduced in the blends in order to improve the performance of PLA/PPC blends as a new material for a fixation plate. Besides, by using the same method of producing PLA/PPC blends, longer durations for in vitro degradation of PLA/PPC blends are essential to further understand the degradation behavior of the blends applied in the human body. Finally, it is also important to further test the mechanical strength of PLA/PPC blends during the degradation period to know the current strength of the implant in the healing process of the bone.

PLA fixation plate and screw can commercially be used in CMF surgery since they reduce cost because of the elimination of secondary surgery to remove the fixation plate and screw after the healing process.

It is hoped that the advantages of this research will ensure the market of PLA product to continue expanding in medical application.

This study is one of the alternative ways for the biomedical researchers to improve the elongation break of PLA. Currently, many researchers focus on polymeric materials such as PLA, poly(glycolic) acid and polydioxanone blends, which were extensively being used in CMF surgery. However, the work on PLA/PPC blends to be used as one of the materials for the CMF fixation plate is very limited, if any. PPC, the proposed material for this research, will improve the mechanical performance of PLA fixation plate and screw to become more sustainable and flexible when applied on human mandible bone.