Search results

The specific iron losses of amorphous alloy material are extremely low compared with silicon steel material. The iron losses of motors may reduce by replacing the silicon steel core with an amorphous alloy core. However, one drawback of amorphous alloy material is that the specific iron losses will increase a lot after the motor manufacturing process. This paper aims to study the influences of interlaminar insulator solidifying and annealing on amorphous alloy material. The iron losses of motors made of amorphous alloy and baseline silicon steel sheets are compared and discussed.

This paper opted for an exploratory study using the experimental analysis and loss separation methods. Two amorphous alloy cores are produced and tested. The iron losses of motors made of amorphous alloy and silicon steel sheets are calculated and compared based on the measured specific iron losses. Three wound amorphous alloy core samples are made and measured. The iron losses are separated and compared by considering the manufacturing influences.

This paper provides empirical insights about what change is brought in amorphous alloy material after manufacturing. The results have shown that, for amorphous alloy cores without the annealing process, the loss increase caused by solidifying is mainly the eddy current loss, while it is mainly the hysteresis loss component for annealed amorphous alloy cores.

This paper presents for the first time the measured results of manufactured amorphous alloy cores. This paper fulfils the need to manufacture amorphous alloy motors properly for the producers.

It has been noted that the spin-valve sensor exhibits lower sensitivity with higher temperature because of the variation of GMR ratio, which could lead to the measurement error in applications where working temperature changes largely over seasons or times. This paper aims to investigate and compensate the temperature effect of the spin-valve sensor.

A spin-valve sensor is fabricated based on microelectronic process, and its temperature relevant properties are investigated, in which the transfer curves are acquired within a temperature range of −50°C to 125°C with a Helmholtz coil and temperature chamber.

It is found that the sensitivity of spin-valve sensor decreases with temperature linearly, where the temperature coefficient is calculated at −0.25 %/°C. The relationship between sensitivity of spin-valve sensor and temperature is well-modeled.

The temperature drift model of the spin-valve sensor’s sensitivity is highly correlated with tested results, which could be used to compensate the temperature influence on the sensor output. A self-compensation sensor system is proposed and built based on the expression modeled for the temperature dependence of the sensor, which exhibits a great improvement on temperature stability.

This chapter deals with firms’ relationships in particular with political actors when expanding in emerging markets. Our main purpose is to illustrate the importance of including such relationships when describing how firms develop insidership in networks in these markets. Emerging markets are often described as if they pose similar challenges but we will focus on the heterogeneity and how firms handle the diversity of the non-business foreign environment. Based on experiences from three Western multinationals — Sandvik, Ericsson and ABB — the main challenges in China, South Africa and Turkey are described. In addition to relationships with political actors, the discussion indicates the importance of also including other non-business actors, such as NGOs. The cases also illustrate that knowledge acquired in one cultural setting may not easily be transferred to another since the contexts are so different.

The purpose of this paper is to quantify the influence of alternating current (AC) interference on hydrogen evolution reaction of X80 steel.

The hydrogen evolution potential was obtained by cathodic potentiodynamic polarization curve. The instantaneous potential under AC interference was obtained by high-frequency acquisition with three-electrode system. Electrochemical impedance spectroscopy and Tafel polarization curves were used to study the influence mechanism of AC interference on instantaneous potential.

It was concluded that the hydrogen evolution reaction could occur on X80 steel under AC interference. There were critical AC current densities of about 100 to 200 A/m2, beyond which the cathode reaction of X80 steel changed from oxygen absorption to hydrogen evolution. Besides the pH value, the initial polarization potential EZ and impedance module of the steel/electrolyte interface under AC interference were also the factors that affected the critical AC densities in different solutions.

This research quantified the hydrogen evolution capacity of X80 steel under AC interference, which could be applied to clear the effect of AC interference on hydrogen evolution reaction.

The purpose of this paper is to study the corrosion behaviors of X70 steel under direct current (DC) interference at 0-1,200 A/m² in simulated soil solution.

The Tafel polarization curves of X70 steel under DC interference were tested using electrochemical method, the corrosion rate was calculated using weight-loss method and the change in steel surface was analyzed by optical microscopy.

The results showed that E-I polarization curves under 200-1,200 A/m² interference were linear; with an increase in the DC density, the corrosion potential of X70 steel shifted positively, solution pH after the weight-loss tests increased and corrosion rate increased linearly. A mathematical relationship between polarization resistance Rp and current density was established. Corrosion morphology indicated that pitting corrosion and crevice corrosion occurred on the X70 steel under DC interference in simulated soil solution.

All tests were conducted at a relative higher DC density (200-1,200 A/m²). The linear fitting method is proposed to fit data of Tafel polarization curves under DC interference. This study provides guidelines for safe operation of X70 steel pipelines.

Alternating current (AC) corrosion is a type of corrosion that occurs in buried pipelines under AC stray current interference, which can increase the hydrogen embrittlement sensitivity of pipelines. However, rare research works have been conducted on the hydrogen permeability characteristics of pipeline steel under AC stray current interference. The purpose of this paper is to study hydrogen permeation behavior of X80 steel under AC stray current interference.

In this paper, the hydrogen permeation behavior of X80 steel under AC interference is studied by AC hydrogen charging experiment in a dual electrolytic cell. The relationship between hydrogen evolution rate and hydrogen permeation flux is studied using the gas collection method. The difference between AC hydrogen permeability and direct current (DC) hydrogen permeability is also discussed.

The anodic dissolution caused by AC corrosion promotes the chemical desorption reaction of the adsorbed hydrogen atoms on the surface, reducing the hydrogen atom absorption ratio by 70%. When the AC is smaller than 150░ A/m², the hydrogen permeation process is controlled by the hydrogen atom generation rate, and the hydrogen permeation flux increases with the increase in hydrogen atom generation rate. When the AC exceeds 400░ A/m², the hydrogen permeation process is controlled by the absorption ratio. The hydrogen permeation flux decreases with the decrease in the absorption ratio. Under AC interference, there is a maximum hydrogen permeation flux that linearly correlates to the H⁺ concentration in the solutions.

The high-strength steel is very sensitive to hydrogen embrittlement, and X80 steel has been widely used in oil and gas pipelines. To date, no research has been conducted on the hydrogen permeation behavior of pipeline steel under AC interference, and the hydrogen permeability characteristics of pipeline steel under AC interference are not clear. The research results of this paper are of great significance for ensuring the intrinsic safety of high-strength pipelines under AC stray current interference.

Due to the rapid development and innovation in the Internet-based technology, conventional banks are under pressure and have to compete with Internet-based finance. This has made banks adopt measures to improve operational efficiency and reduce input and increase output.

The authors had proposed a two-stage fairness concern efficiency model based on the classical theory of data envelopment analysis (DEA) and performed an empirical study to measure agricultural loan efficiency in the 20 major Chinese banks.

The findings of the empirical analysis are as follows: (1) peer-induced fairness concern has no impact on deposit efficiency in a centralized bank supply chain; (2) The China Merchants Bank (CMB) has the third lowest deposit efficiency; (3) monotonicity of loan efficiency with input allocation depends on a bank's ownership structure; (4) efficiency ranks are strongly affected by the fairness concern; (5) most Chinese banks show a low agricultural loan efficiency.

This paper contributes to the literature in several ways. First, to the best of the authors’ knowledge, this is the first attempt to analyze agricultural loan efficiency for a bank supply chain system with the fairness concern. This work reveals the hidden factor that restricts loan efficiency of Chinese banks. Second, the proposed fairness concern two-stage DEA model has shown good ability for full ranking. It can provide a new perspective to the classical DEA literature for ranking decision-making units (DMUs). Third, the authors have demonstrated empirical bank efficiency for the 20 major Chinese banks.

The purpose of this paper was to investigate the corrosion behavior of X65 steel in the CO₂/oil/water environment using mass loss method, potentiodynamic polarization technique and characterization of the corroded surface techniques.

The weight loss analysis, electrochemical study and surface investigation were carried out on X65 steel that had been immersed in the CO₂/oil/water corrosive medium to understand the corrosion behavior of gathering pipeline steel. The weight loss tests were carried out in a 3L autoclave, and effects of flow velocity, CO₂ partial pressure and water cut on the CO₂ corrosion rate of X65 steel were studied. Electrochemical studies were carried out in a three-electrode electrochemical cell with the test temperature of 60°C and CO₂ partial pressure of 1 atm by recording open circuit potential/time and potentiodynamic polarization characteristics. The surface and cross-sectional morphologies of corrosion product scales were characterized using scanning electron microscopy. The phases of corrosion product scales were investigated using X-ray diffraction.

The results showed that corrosion rates of X65 steel both increased at first and then decreased with the increase of flow velocity and CO₂ partial pressure, and there were critical velocity and critical pressure in the simulated corrosive environment, below the critical value, the corrosion products formed on the steel surface were loose, porous and unstable, higher than the critical value, the corrosion product ?lms were dense, strong adhesion, and had a certain protective effect. Meanwhile, when the flow velocity exceeded the critical value, oil film could be adsorbed on the steel surface more evenly, corrosion reaction active points were reduced and the steel matrix was protected from being corroded and crude oil played a role of inhibitor, thus it influenced the corrosion rate. Above the critical CO₂ partial pressure, the solubility of CO₂ in crude oil increased, the viscosity of crude oil decreased and its fluidity became better, so that the probability of oil film adsorption increased, these factors led to the corrosion inhibition of X65 steel reinforced. The corrosion characteristics of gathering pipeline steel in the corrosive environment containing CO₂ would change due to the presence of crude oil.

The results can be helpful in selecting the suitable corrosion inhibitors and targeted anti-corrosion measures for CO₂/oil/water corrosive environment.