Search results

The purpose of this paper is to report on a method of synthesis of TiO₂‐SiO₂ oxide composites characterised by spherically shaped particles with sizes in the micrometric ranges, which can be applied as a new generation of textile/TiO₂‐SiO₂ composites with barrier properties against UV radiation. Synthesis and characterisation of TiO2‐SiO2 oxide composites with a high degree of dispersion were performed, and their influence on the barrier properties of textile fabrics was investigated.

The precipitation was performed with the use of solutions of titanium sulphate and sodium silicate as the precipitating agent, which are cheap alternatives to organic precursors of Ti and Si. The reaction was conducted in an emulsion system, where cyclohexane was used as the organic phase and non‐ionic surfactants NP3 and NP6 as emulsifiers were applied.

The direction of substrate supply, concentration of the reagents and their ratio and other conditions of precipitation process were found to significantly affect the physicochemical parameters of the pigments obtained. A possibility is provided of manufacturing a new generation of textile/TiO2‐SiO2 composites with barrier properties against UV radiation.

Titanium sulphate, sodium silicate, cyclohexane as the organic phase, and non‐ionic surfactants NP3 and NP6 as emulsifiers, were used.

Synthesis of a new generation of textile/TiO2‐SiO2 composites with barrier properties against UV radiation has been performed. Textile fabrics modified with hybrid composites demonstrated high absorption of UV radiation over the full wavelength range.

Determination of optimum conditions of TiO2‐SiO2 oxide composites precipitation to obtain products with desired physicochemical, dispersive and structural properties. Development of nano‐structural textile composites with barrier properties, protecting against UV radiation.

The purpose of this paper is to obtain ZnO‐SiO₂ oxide composites of low bulk density, high homogeneity and consisting of the smallest possible particles. The optimum parameters of precipitation of ZnO‐SiO₂ oxide composites impregnated with natural latex rubber were established. The formation and impregnation the ZnO‐SiO₂ oxide composites were made to occur simultaneously.

The influence of non‐ionic surfactants added during the precipitation process on the physico‐chemical properties of the oxide systems obtained was investigated. The products were characterised by determination of bulk density, absorption capacities of water and paraffin oil, particle size distribution (applying NIBS and laser diffraction methods), as well as SEM observations of surface morphology and microstructure. Moreover, the colorimetric characteristics of the oxide composites obtained and sedimentation profiles in water were analysed. Energo‐dispersive microanalysis of the products enabled determination of the content of ZnO and SiO₂. The surface area (BET) and the size and volume of pores were also estimated.

Modification of the oxide composites with nonylphenylpolyoxyethyleneglycol ethers was found to improve the basic physico‐chemical parameters of the ZnO‐SiO₂ hybrid systems and to change the character of its surface to become more hydrophobic. The conditions in which samples with the best properties were obtained were concluded to be optimum.

Only the selected non‐ionic surfactants were applied as modifying agents of ZnO‐SiO₂.

There is a possible application of ZnO‐SiO₂ oxide composites as activators of rubber compounds and barrier materials in textiles.

The proposed method of ZnO‐SiO₂ oxide composite synthesis in the process of precipitation with simultaneous modification with non‐ionic surfactants provides products with desirable dispersive‐morphological parameters and a hydrophobic surface character.

The purpose of this paper is to propose a new method of synthesis of CuO · SiO₂ oxide composite based on the reaction of precipitation from water solutions of sodium silicate and copper nitrate.

Solutions of sodium silicate and copper nitrate were used as substrates. The effects of direction of substrate supply, concentration, excess of reagents and temperature of precipitation on the physicochemical properties of the products were analysed.

A new method of synthesis of CuO · SiO₂ oxide composite based on a precipitation reaction is proposed.

Only sodium silicate and copper nitrate solutions were used.

The CuO · SiO₂ oxide composite obtained can be used as blue pigment or polymer filler.

The paper determines optimum conditions of CuO · SiO₂ oxide composite precipitation to obtain products with desired physicochemical, dispersive and structural properties.

The purpose of this paper is to characterise the electrokinetic properties of pigments supported on both unmodified and modified silica. The paper describes the preparation of hybrid pigments via adsorption of organic dyes on silica supports and determination of the zeta potential and electrophoretic mobility of the materials obtained.

The materials studied were hybrid pigments obtained as a result of adsorption of two basic dyes: C.I. Basic Red 1 and C.I. Basic Orange 14 and one acidic dye C.I. Mordant Red 3 from solutions of concentrations of 500, 2,000 and 3,000 mg/dm³ on the surface of both unmodified and modified silica supports. The agent used for modification of the silica surface was N‐2‐(aminoethyl)‐3‐aminopropyltrimethoxysilane.

The modification of the silica surface with aminosilane was found to change, significantly, the electrokinetic character of the inorganic support. This change was interpreted as being due to the ionisation of −NH₂ groups from the modifier molecule, which changes the surface charge. Electrokinetic curves of the pigment composites changed considerably as a function of the type and concentration of the organic dye adsorbed.

Only SiO2 supports (unmodified and aminosilane‐grafted) and C.I. Basic Red 1, C.I. Basic Orange 14 or C.I. Mordant Red 3 dyes adsorbed on its surface were evaluated. Other dyes could also be studied.

Measurements of the zeta potential were used to characterise the stability of colloidal dispersions of paints or dyes and to control the stability of paints on storage and their performance on painting and drying.

The paper demonstrates that the measurements of zeta potential permit determination of the optimum conditions for the use of a given pigment. The finding of the change of the zeta potential of a given pigment and so, also its application properties as a result of different functional groups in the dye or the modifying agent molecules.

The study reported here concerned production of green pigments, hydrated nickel(II) silicates and oxides, obtained by precipitation from solutions of sodium metasilicate and sodium hydroxide using nickel(II) sulphate.

The pigments were analysed using a number of techniques including scanning electron microscopy for particle surface morphology and dynamic light scattering for particle structure and the tendency of the particles to agglomerate.

The most desirable physicochemical parameters were shown by highly dispersed nickel(II) silicates precipitated in presence of the modifying agents. Silicate pigments precipitated in the presence of Rokanol K‐7 had low bulk densities, a high capacity to absorb water, dibutyl phthalate and paraffin oil within the primary particles, which is particularly noteworthy.

Due to their good dispersibility, well developed surface and appropriate coating power, coloured silicates of, e.g. chromium(III) and nickel(II) may be used as pigments and fillers for surface coatings.

The method of obtaining nickel(II) pigments developed was novel and provided a solution for problem of post‐galvanic nickel solutions.

This study aims to perform the surface treatment of synthetic α-Fe₂O₃ red iron oxide pigment with hydrolysate 3-aminopropyl silane (A) and colloidal silica (CS) and investigate the effects of surface-treated pigment on the styrene acrylic (SA) emulsion and polyurethane (PU) dispersion.

For this purpose, firstly red iron oxide particles were modified with A and CS separately in an aqueous medium. After isolation of the modified iron oxide were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS). Moreover, the degree of the dispersion stability of the modified pigment in coatings with SA emulsion and PU dispersion was investigated by using an oscillation rheometer. Loss (G''), storage (G') modulus, loss factor [tan(δ)] and yield stress (τ⁰) values were determined by performing amplitude and frequency sweep tests.

The τ⁰ in SA coatings decreases with the amount of used A and increases with the amount of used CS. The τ⁰ decreases as the amount of used A and CS in PU coatings increases. The use of CS on red iron oxide pigments causes storage modulus to increase in SA coatings at low angular frequencies, while it causes a decrease in PU coatings.

To the best of the authors’ knowledge, for the first time, the suspended state of the iron oxide hybrid pigment formed with CS in the coating was investigated rheologically in this study.

The purpose of the study reported in this paper was to prepare modified C.I. Pigment Red (PR) 170 to reduce production cost and improve application performance. The structure of the modified pigment was characterised. The colour strength, thermal stability, mobility, aqueous dispersability and ultraviolet (UV) resistance of modified pigments were studied.

Silica fume was added into the diazonium salt solution under acidic condition, followed by the activation to generate new surface. Subsequently, coupling component was dropwise added to the system to form the modified pigments evenly on the surface of silica fume in situ. The structure and properties of the modified pigment were studied by fourier transform infrared spectoscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermal gravity analysis (TG-DTA), UV-visible diffuse reflectance spectra (UV-Vis DRS), and commission internationale de L‘Eclairage (CIE L*a*b*) colour measurements.

The morphology and particle size of the modified pigment were controlled by the modification of the silica fume, and the organic pigment and silica fume formed a core–shell structure. The properties of the modified pigment including colour strength, thermal stability, mobility, aqueous dispensability and UV resistance were improved significantly.

The effect of the amount of silica fume on the thickness of the organic pigment layer and the effect of the thickness of the organic pigment layer on the properties of the modified pigment need to be studied further.

This paper shows a feasible method of the modification of the PR170 with the silica fume, and the modification can improve the properties of the PR170. The use of silica fume to modify organic pigment can realise the reuse of solid waste and reduce the production cost of the organic pigment.

This modification method of the organic pigment is adaptive and it can be adjusted to the modification of other species of the organic pigment.

The modification of the PR170 with the silica fume was carried out in its preparation process, which synchronised the preparation and modification of the organic pigment. The properties of the modified pigment were improved, which were beneficial for their application in inks and coatings.

This paper presents the experimental and numerical results of the bending properties of low-height prestressed T-beams. The purpose is to study the bearing capacity, failure state and strain distribution of low-height prestressed T-beams.

First, two 13 m-long full-size test beams were fabricated with different positions of prestressed steel bundles in the span. The load–deflection curves and failure patterns of each test beam were obtained through static load tests. Secondly, the test data were used to validate the finite element model developed to simulate the flexural behavior of low-height prestressed T-beams. Finally, the influence of different parameters (the number of prestressed steel bundles, initial prestress and concrete strength grade) on the flexural performance of the test beams is studied by using a finite element model.

The test results show that when the distance of the prestressed steel beam from the bottom height of the test beam increases from 40 to 120 mm, the cracking load of the test beam decreases from 550.00 to 450.00 kN, reducing by 18.18%, and the ultimate load decreases from 1338.15 to 1227.66 kN, reducing by 8.26%, therefore, the increase of the height of the prestressed steel beam reduces the bearing capacity of the test beam. The numerical simulation results show that when the number of steel bundles increases from 2 to 9, the cracking load increases by 183.60%, the yield load increases by 117.71% and the ultimate load increases by 132.95%. Therefore, the increase in the number of prestressed steel bundles can increase the cracking load, yield load and ultimate load of the test beam. When the initial prestress is from 695 to 1,395 MPa, the cracking load increases by 69.20%, the yield load of the bottom reinforcement increases by 31.61% and the ultimate load increases by 3.97%. Therefore, increasing the initial prestress can increase the cracking load and yield load of the test beam, but it has little effect on the ultimate load. The strength grade of concrete increases from C30 to C80, the cracking load is about 455.00 kN, the yield load is about 850.00 kN and the ultimate load is increased by 4.90%. Therefore, the improvement in concrete strength grade has little influence on the bearing capacity of the test beam.

Based on the experimental study, the bearing capacity of low-height prestressed T-beams with different prestressed steel beam heights is calculated by finite element simulation, and the influence of different parameters on the bearing capacity is discussed. This method not only ensures the accuracy of bearing capacity assessment, but also does not require a large number of samples and has a certain economy. The study of prestressed low-height T-beams is of great significance for understanding the principle and application of prestressed technology. Research on the mechanical behavior and performance of low-height prestressed T beams can provide a scientific basis and technical support for the design and construction of prestressed concrete structures. In addition, the study of prestressed low-height T-beams can also provide a reference for the optimization design and construction of other structural types.