Search results

Significant achievements in ferrite material processing enable developments of many ferrite devices with a wide range of power levels and working frequencies, which make demands for new characterization and modelling methods for ferrite materials and components. The purpose of this paper is to introduce a modelling and measurement procedure, which can be used for the characterization of two‐port ferrite components in high frequency range.

This paper presents a commercially available ferrite component (transformer) modelling and determination of its electrical parameters using in‐house developed software. The components are measured and characterized using a vector network analyzer E5071B and adaptation test fixture on PCB board. The parameters of electrical equivalent circuit of the ferrite transformer parameters are compared with values extracted out of measured scattering parameters.

A good agreement between modelled and extracted electrical parameters of the ferrite transformer is found. The modelled inductance curves have the same dependence versus frequency as extracted ones. That confirms the model validity in the wide frequency range.

In‐house developed software based on proposed model provides inclusion of the ferrite material dispersive characteristics, which dominantly determines high‐frequency behaviour of two‐port ferrite components. Developed software enables fast and accurate calculation of the ferrite transformer electrical parameters and its redesign in order to achieve the best performance for required application.

The purpose of this paper is to test the measurement performances of a planar‐type meander sensor installed in robot foot in order to examine its potential application as ground reaction force sensor.

A planar‐type meander sensor is composed of two pairs of meander coils. Variation of input inductance between coils serves as a measure of small displacements in a plane. Pairs of meander coils are installed in an actuated robot foot to measure displacements proportional to normal or tangential components of ground reaction force which acts upon the foot. The sensor was modeled by the concept of partial inductance and a new simulation tool was developed based on this concept.

Pairs of meander coils were tested against angular displacements, and results showed that the sensor gives correct information about displacement regardless how the foot touches the ground with its whole area. Deviations between position of computed and real acting point of ground reaction force are relatively small. Owing to good results obtained, a miniaturized sensor was developed having the same performances as previously developed prototype.

This paper presents initial work in implementing a planar‐type meander sensor in robot foot as to measure ground reaction force. Developed simulation tool gives accurate analysis of inductance variation of meander structures. In addition, the measurement error and sensor's nonlinearity are analyzed. Calculated results show a good agreement with experimental results. Hence, miniaturized sensor, easier for implementation, is proposed.

The appropriate selection of a testing method largely determines the accuracy of a measurement. Parasitic effects associated with test fixture demand a significant consideration in a measurement. The purpose of this paper is to introduce a measurement procedure which can be used for the characterization of surface mount devices (SMD) components, especially devoted to SMD inductors.

The paper describes measurement technique, characterization, and extracting parameters of SMD components for printed circuit board (PCB) applications. The commercially available components (multi‐layer chip SMD inductors in the ceramic body) are measured and characterized using a vector network analyzer E5071B and adaptation test fixture on PCB board. Measurement results strongly depend on the choice of the PCB; the behaviour of the component depends on the environment where the component is placed.

The equivalent circuit parameters are extracted in closed form, from an accurate measurement of the board‐mounted SMD inductor S‐parameters, without the necessity for cumbersome optimization procedures, which normally follow the radio frequency circuit synthesis.

It this paper, a new adaptation test fixture in PCB technology is realized. It is modeled and it has provided the extraction of parameters (intrinsic and extrinsic) of SMD inductor with great accuracy.

Present 3D electromagnetic simulators have high accuracy, but they are time and memory expensive. Because of that, fast and simple expression for impedance is also necessary for initial inductor design. In this paper new efficient method for total impedance calculation of ferrite electromagnetic interference (EMI) suppressor is given. By using an algorithm, it is possible to predict correctly all variations of electrical characteristics introduced by varying geometry parameters of EMI suppressor.

The starting point for calculation of electrical characteristics of EMI suppressor is Greenhouse theory. Greenhouse decomposed inductor into its constituent segments. Basically, all segments of conductive layer are divided into parallel filaments having small, rectangular cross sections. The self‐ and mutual‐inductance were calculated using the concept of partial inductance. Total impedance of EMI suppressor is calculated taking care of dimension of chip size, material that are used and geometry of conductive layer.

The Simulator for Planar Inductive Structures (SPIS™) simulates effects of ferrite materials and geometrical parameters of planar inductive structures. With proposed software tool, designers can predict performance parameters quickly and easily before costly prototypes are built. SPIS™ software offers substantially reduced time to market, and increases device performance. The computed impedances, given by our software tool are compared with measured data and very good agreement was found.

Applied flexible efficient methods for impedance calculation of EMI suppressor are able to significantly increase the speed design of multilayer suppressors for universal series bus, low‐voltage differential signaling and in other high‐speed digital interfaces incorporated in notebooks and personal computers, digital cameras and scanners. Also, ferrite suppressors have been successfully employed for attenuating EMI in switching power supplies, electronic ignition systems, garage door openers, etc.

The paper presents realized structures of ferrite EMI suppressors. New geometries of conductive layer are proposed. In addition, using simple model of inductor, the paper develops a CAD simulation tool SPIS™ for calculation of electrical characteristics of EMI suppressors with different geometry of conductive layer.

Present 3D electromagnetic simulators have high accuracy but they are time and memory expensive. Owing to a fast and simple expression for inductance is also necessary for initial inductor design. In this paper, new efficient methods for total inductance calculation of meander inductor, are given. By using an algorithm, it is possible to predict correctly all inductance variations introduced by varying geometry parameters such as number of turns, width of conductor or spacing between conductors.

The starting point for the derivation of the recurrent formula is Greenhouse theory. Greenhouse decomposed inductor into its constituent segments. Meander inductor is divided into straight conductive segments. Then the total inductance of the meander inductor is a sum of self‐inductances of all segments and the negative and positive mutual inductances between all combinations of straight segments. The monomial equation for the total inductance of meander inductor has been obtained by fitting procedure. The fitting technique, using the method of least squares, finds the parameters of the monomial equation that minimize the sum of squares of the error between the accurate data and fitted equation. The paper presents new expression for inductance of meander inductor, in the monomial form, which is suitable for optimization via geometric programming. The computed inductances are compared with measured data from the literature.

The first, recurrent, expression has the advantage that it indicates to the designer how the relative contributions of self, positive, and negative mutual inductance are related to the geometrical parameters. The second expression presents the inductance of the meander inductor in the monomial form, so that the optimization of the inductor can be done by procedure of the geometric programming. Simplicity and relatively good accuracy are the advantages of this expression, but on the other hand the physical sense of the expression is being lost. Thus, the effects of various geometry parameters on inductance are analyzed using two expressions and the software tool INDCAL.

Applied flexible efficient methods for inductance calculation of meander inductor are able to significantly increase the speed of RF and sensor integrated circuit design.

For the first time a simple expression for fast inductance calculation for meander inductor in monomial form is presented. It is explained how such an expression is generated, which can be directly implemented in circuit simulators.