Search results

Lead emissions from vehicles using leaded gasoline is a serious environmental problem in urban areas. While leaded gasoline has been completely phased out in many developed countries, it is still the predominant fuel grade in most developing countries. This paper presents an estimation of the health and economic benefits and costs of the transition from leaded to unleaded gasoline in Lebanon based on relevant dose‐response functions and available country‐specific data. Comparing the potential costs of the phase‐out and the predicted benefits, it was concluded that such action is economically highly justified.

The purpose of this study is to introduce a new type of sensor which uses microwave metamaterials and direct-coupled split-ring resonators (DC-SRRs) to measure the dielectric properties of solid materials in real time. The sensor uses a transmission line with a bridge-type structure to measure the differential frequency, which can be used to calculate the dielectric constant of the material being tested. The study aims to establish an empirical relationship between the dielectric properties of the material and the frequency measurements obtained from the sensor.

In the proposed design, the opposite arm of the bridge transmission line is loaded by DC-SRRs, and the distance between DC-SRRs is optimized to minimize the mutual coupling between them. The DC-SRRs are loaded with the material under test (MUT) to perform differential permittivity sensing. When identical MUT is placed on both resonators, a single transmission zero (notch) is obtained, but non-identical MUTs exhibit two split notches. For the design of differential sensors and comparators based on symmetry disruption, frequency splitting is highly useful.

The proposed structure is demonstrated using electromagnetic simulation, and a prototype of the proposed sensor is fabricated and experimentally validated to prove the differential sensing principle. Here, the sensor is analyzed for sensitivity by using different MUTs with relative permittivity ranges from 1.006 to 10 and with a fixed dimension of 9 mm × 10 mm ×1.2 mm. It shows a very good average frequency deviation per unit change in permittivity of the MUTs, which is around 743 MHz, and it also exhibits a very high average relative sensitivity and quality factor of around 11.5% and 323, respectively.

The proposed sensor can be used for differential characterization of permittivity and also as a comparator to test the purity of solid dielectric samples. This sensor most importantly strengthens robustness to environmental conditions that cause cross-sensitivity or miscalibration. The accuracy of the measurement is enhanced as compared to conventional single- and double-notch metamaterial-based sensors.

The purpose of this paper is to summarize the current applications of BIM, the integration of related technologies and the tendencies and challenges systematically.

Using quantitative and qualitative bibliometric statistical methods, the current mode of interaction between BIM and other related technologies is summarized.

This paper identified 24 different BIM applications in the life cycle. From two perspectives, the implementation status of BIM applications and integrated technologies are respectively studied. The future industry development framework is drawn comprehensively. We summarized the challenges of BIM applications from the perspectives of management, technology and promotion, and confirmed that most of the challenges come from the two driving factors of promotion and management.

The technical challenges reviewed in this paper are from the collected literature we have extracted, which is only a part of the practical challenges and not comprehensive enough.

We summarized the current mode of interactive use of BIM and sorted out the challenges faced by BIM applications to provide reference for the risks and challenges faced by the future industry.

There is little literature to integrate BIM applications and to establish BIM related challenges and risk frameworks. In this paper, we provide a review of the current implementation level of BIM and the risks and challenges of stakeholders through three aspects of management, technology and promotion.

This paper aims to address the production of biocomposite nanofibers using luffa natural fibers and polyaniline conductive polymer/polyethylene oxides (PANI/PEO).

In this study, luffa natural fibers are extracted by chemical method. After mixing the treated luffa (TL) with the PANI/PEO solution, TL/PANI/PEO nanofibers were produced by electrospinning (ES) method under different ES parameters to examine the optimal conditions for nanofiber production. Then TL/PANI/PEO biocomposite nanofibers prepared in different weight ratios were produced to analyze the effects of luffa in the morphology and thermal properties of the biocomposite nanofibers. The characterization analysis of TL/PANI/PEO biocomposite nanofibers was performed by scanning electron microscopy, Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) analysis methods.

The analysis shows that different weight ratios of TL to PANI/PEO changed the morphology of the membrane. When increasing the weight ratio of TL, the morphological structure of TL/PANI/PEO transformed from nanofiber structure to thin film structure. The appearance of O—H peaks in the FTIR results proved the existence of TL in PANI/PEO nanofibers (membrane). Moreover, an increase in the weight ratio of luffa from 2% to 7.5% leads to an increase in the peak intensity of the O—H group. Regarding DSC analysis, biocomposite nanofibers improved the thermal properties. According to all results, 2%wt TL/PANI/PEO showed optimal morphological properties.

Plant cellulose was extracted from the luffa, one of the natural fibers, by method of alkali treatment. A new type of biocomposite nanofibers was produced using TL blend with PANI via electrospinning method.

The purpose of this study is to prepare a new adsorbent activated carbon immobilized on polystyrene (ACPS) for uranium (VI) and thorium (IV) removal from an aqueous solution. Activated carbon (AC) was derived from biochar material by chemical activation to increase the active sites on its surface and enhance the adsorption capacity. Activated carbon (AC) was immobilized on polystyrene (PS) to improve the physical properties and facilitate separation from the working solution. A feasibility study for the adsorption of uranium (VI) and thorium (IV) on the new adsorbent (ACPS) has been achieved. Adsorption kinetics, isotherms, and thermodynamics models of the adsorption process were used to describe the reaction mechanism.

Activated carbon was synthesized from biochar charcoal by 2 M H₂SO₄. Activated carbon was immobilized on the pretreatment polystyrene by hydrothermal process forming new adsorbent (ACPS). Characterization studies were carried out by scanning electron microscope, energy-dispersive X-ray spectrometer, infrared spectroscopy and X-ray diffraction techniques. Different factors affect the adsorption process as pH, contact time, solid/liquid ratio, initial concentration and temperature. The adsorption mechanism was explained according to kinetic, isothermal and thermodynamic studies. Also, the regeneration of spent ACPS was studied.

The experimental results showed that pH and equilibrium time of the best adsorption were 6.0 and 60 min for U(VI), 4.0 and 90 min for Th(IV), (pH_PZC = 3.4). The experimental results fit well with pseudo-second order, Freundlich and Dubinin–Radushkevich models proving the chemisorption and heterogenous adsorption reaction. Adsorption thermodynamics demonstrated that the adsorption process is exothermic and has random nature of the solid/liquid interface. In addition, the regeneration of spent ACPS research showed that the adsorbent has good chemical stability. According to the comparative study, ACPS shows higher adsorption capacities of U(VI) and Th(IV) than other previous bio-adsorbents.

This study was conducted to improve the chemical and physical properties of bio-charcoal purchased from the local market to activated carbon by hydrothermal method. Activated carbon was immobilized on polystyrene forming new adsorbent ACPS for eliminating U(VI) and Th(IV) from aqueous solutions.