Search results

Selective laser sintering (SLS) is an essential technology in the field of additive manufacturing. However, SLS technology is limited by the traditional point-laser sintering method and has reached the bottleneck of efficiency improvement. This study aims to develop an image-shaped laser sintering (ISLS) system based on a digital micromirror device (DMD) to address this problem. The ISLS system uses an image-shaped laser light source with a size of 16 mm × 25.6 mm instead of the traditional SLS point-laser light source.

The ISLS system achieves large-area image-shaped sintering of polymer powder materials by moving the laser light source continuously in the x-direction and updating the sintering pattern synchronously, as well as by overlapping the splicing of adjacent sintering areas in the y-direction. A low-cost composite powder suitable for the ISLS system was prepared using polyether sulfone (PES), pinewood and carbon black (CB) powders as raw materials. Large-sized samples were fabricated using composite powder, and the microstructure, dimensional accuracy, geometric deviation, density, mechanical properties and feasible feature sizes were evaluated.

The experimental results demonstrate that the ISLS system is feasible and can print large-sized parts with good dimensional accuracy, acceptable geometric deviations, specific small-scale features and certain density and mechanical properties.

This study has achieved the transition from traditional point sintering mode to image-shaped surface sintering mode. It has provided a new approach to enhance the system performance of traditional SLS.

The range of applications of the currently available biomass selective laser sintering (SLS) parts is limited and low-quality. This study aims to demonstrate the effects of the various processing parameters on the dimensional accuracy, bending strength, tensile strength, density and impact strength of the Prosopis chilensis/polyethersulfone (PES) composites (PCPCs) that were produced by SLS. The various processing parameters are laser power, scan speed, preheating temperature, scan spacing and layer thickness. In addition, the authors’ studied the effects of PCP particle size on the mechanical properties of the PCPCs.

The PCPC specimens were printed using an AFS SLS machine (additive manufacturing). The bending, tensile and impact strengths of the specimens were measured using a universal tensile tester. The dimensional accuracy of the bending specimens was determined by a Vernier caliper. The formability of the PCPC at various mixing ratios of the raw materials was earlier investigated by single-layer sintering experiments (Idriss et al., 2020b). The microstructure and particle distribution of the various PCPC specimens were analyzed by scanning electron microscopy (SEM).

The mechanical strengths (bending, tensile and impact strengths and density) and the dimensional accuracy of the PCPC SLS parts were directly and inversely proportional, respectively, to the laser power and preheating temperature. Furthermore, the mechanical strengths and dimensional accuracy of the PCPC SLS parts were inversely and directly proportional, respectively, to the scanning speed, scan spacing and layer thickness.

PCPC is an inexpensive, energy-efficient material that can address the drawbacks of the existing SLS parts. It is also eco-friendly because it lowers the pollution and CO₂ emissions that are associated with waste disposal and SLS, respectively. The optimization of the processing parameters of SLS in this study produced high-quality PCPC parts with high mechanical strengths and dimensional accuracy that could be used for the manufacture of the roof and wooden floors, construction components and furniture manufacturing.

To the best of the authors’ knowledge, this study is among the first to elucidate the impact of the various SLS processing parameters on the mechanical properties and dimensional accuracy of the sintered parts. Furthermore, novel PCPC parts were produced in this study by SLS.

This paper aims to propose a suitable atomizing solidification chitosan (CS) gel liquid extrusion molding technology for the three dimensional (3D) printing method, and experiments verify the feasibility of this method.

This paper mainly uses experimental means, combined with theoretical research. The preparation method, solidification forming method and 3D printing method of CS gel solution were studied. The CS gel printing mechanism and printing error sources are analyzed on the basis of the CS gel ink printing results, printing performance with different ratios of components by constructing a gel print prototype, experiments evaluating the CS gel printing technology and the effects of the process parameters on the scaffold formation.

CS printing ink was prepared; the optimal formula was found; the 3 D printing experiment of CS was completed; the optimal printing parameters were obtained; and the reliability of the forming prototype, printing ink and gel printing process was verified, which allowed for the possibility to apply the 3 D printing technology to the manufacturing of a CS gel structure.

This study can provide theoretical and technical support for the potential application of CS 3 D printed gels in tissue engineering.

The purpose of this paper is to explore the influence of organizational culture (OC) on talent management (TM) by a case study of a real estate company.

The method of case study is adopted in the present study.

The authors present four propositions. The first is OC has an effect on TM. The second is a new conceptual model of TM. The third is a 4-P pattern to identify and develop the talent. The fourth is to adopt both the spiritual and material satisfactions that retain the talent.

The primary limitation of this study is embedded in the case study method, which is not sufficient to represent the totality. The other limitation is that the issue of cohesion and team efficacy of talents is not considered. This study argues the relationship between OC and TM and expands the existing TM and OC theory. The effect of professional idealism is emphasized on in the process of TM. Talent can be retained firmly within the organization through the methods of rebuilding and strengthening OC.

A conceptual model of TM, 4-P pattern of evaluation and the operational mean to retain the talent is introduced.

Considering the problem that the high recognition rate of deep learning requires the support of mass data, this study aims to propose an insulating fault identification method based on small data set convolutional neural network (CNN).

Because of the chaotic characteristics of partial discharge (PD) signals, the equivalent transformation of the PD signal of unit power frequency period is carried out by phase space reconstruction to derive the chaotic features. At the same time, geometric, fractal, entropy and time domain features are extracted to increase the volume of feature data. Finally, the combined features are constructed and imported into CNN to complete PD recognition.

The results of the case study show that the proposed method can realize the PD recognition of small data set and make up for the shortcomings of the methods based on CNN. Also, the 1-CNN built in this paper has better recognition performance for four typical insulation faults of cable accessories. The recognition performance is improved by 4.37% and 1.25%, respectively, compared with similar methods based on support vector machine and BPNN.

In this paper, a method of insulation fault recognition based on CNN with small data set is proposed, which can solve the difficulty to realize insulation fault recognition of cable accessories and deep data mining because of insufficient measure data.

This study aims to examine the problems encountered during the establishment of the Central Police Academy (CPA) under the Nationalist regime from 1936 to 1949. While the authoritarian party-state unified the police academies by forceful means, this catalyzed the cleavage between the schools of police studies and resulted in power struggles over police education, intellectual thought, collectivity and even the national reform of police administration. More than narrating the progress of power consolidation, this study attempts to identify the problems underlying the factional strife and to reveal the interwoven pattern of these power struggles, exploring the confusion regarding what the police is, a question that troubled Chinese policemen from the mainland to Taiwan.

This paper explains the emergence of the factional strife from the beginning of the preliminary growth of the Police Academies in Nanking and Chekiang. It widely makes use of the official archives from Japan Center for Asian Historical Records and Historica Academia to show the dynamic situation in police education and administration. Rather, the official publications of the Police Academies and their affiliated associations reveal the hidden political agenda behind a unified framework as the party-state claimed. Moreover, official gazettes, memorials and newspapers are also used to strengthen the core argument of this study.

This paper examines the impact of the factional strife between the police leaders Dai Li and Li Shizhen on the CPA from 1936 to 1949. It illustrates that the establishment of the CPA ostensibly unified the nationwide police force but triggered power struggles over the control of the police administration. More importantly, it also shows how the factions strove for larger shares of power under the supreme doctrines that Chiang Kai-shek and the party-state imposed.

The failure of police education to become powerful was a special case among other more typical institutions. The governors coercively merged the police academies and created robust conditions for growth under the shelter of state authority. The police force did not follow the same path of national monopoly as what recent studies found but drifted apart with its vested interests and incompatible beliefs. Hence, the greater the demand for centralized control by the state, the greater the tension of the factional strife.

This paper aims to describe typical regional document supply networks in China through detailed discussion of their framework, service mode and influence on the nationwide document supply networks.

This paper highlights various kinds of regional document supply networks in China that serve as document resource sharing cooperation networks within provinces, cities and university towns. Their framework, service mode and influence on the nationwide document supply networks are discussed, followed by suggestions for improvement.

Regional document supply networks have their natural advantages in local financial support and extensive local coverage and are capable of providing fine service to meet various user needs timely and economically. They become an important part and beneficial supplement to nationwide document supply networks.

This paper studies regional document supply networks in China which has rarely been addressed in the international library literature.