Search results

The wear of an abrasive single-crystal diamond (SCD) grit affects the machining quality of the sapphire wafer. This paper aims to investigate the influence of crystallographic orientation on the wear characteristics of SCD grit scratching on sapphire.

The wear characteristics of two SCD grits (SCD100 and SCD111) with different crystallographic orientations were systematically investigated. The wear mechanism involved in the scratching process was explored. The wear morphology, scratching forces and friction coefficient during the scratching process were measured and analyzed.

The experiment results show that the wear progress of the two SCD grits is obviously different. The wear resistance of SCD111 grit is greater than that of SCD100 grit in normal wear stage. However, the SCD100 grit could remove more sapphire material than SCD111 grit. The SCD grits mainly sustain extrusion stress and shear stress during scratching on sapphire. The crystallographic orientation of SCD grits plays a significant role in the wear progress during scratching on sapphire.

The results of the experimental studies could provide a theoretical foundation for improving the fabrication of abrasive diamond tools.

This paper aims to study the wear properties of electron beam melted Ti6Al4V (EBM-Ti6Al4V) in simulated body fluids for orthopedic implant biomedical applications compared with wrought Ti6Al4V (Wr-Ti6Al4V).

Wear properties of EBM-Ti6Al4V compared with Wr-Ti6Al4V against ZrO₂ and Al₂O₃ have been investigated under dry friction and the 25 Wt.% newborn calf serum (NCS) lubricated condition using a ball-on-disc apparatus reciprocating motion. The microstructure, composition and hardness of the samples were characterized using scanning electron microscopy (SEM), x-ray diffraction and a hardness tester, respectively. The contact angles with 25 Wt.% NCS were measured by a contact angle apparatus. The wear parameters, wear 2D and 3D morphology were obtained using a 3D white light interferometer and SEM.

EBM-Ti6Al4V yields a higher contact angle than the Wr-Ti6Al4V with the 25 Wt.% NCS. EBM-Ti6Al4V couplings exhibit lower coefficients of friction compared with the Wr-Ti6Al4V couplings under both conditions. There is only a slight difference in the wear resistance between the Wr-Ti6Al4V and EBM-Ti6Al4V alloys. Both Wr-Ti6Al4V and EBM-Ti6Al4V suffer from similar friction and wear mechanisms, i.e. adhesive and abrasive wear in dry friction, while abrasive wear under the NCS condition. The wear depth and wear volume of the ZrO₂ couplings are lower than those of the Al₂O₃ couplings under both conditions.

This paper helps to establish baseline bio-tribological data of additively manufactured Ti6Al4V by electron beam melting in simulated body fluids for orthopedic applications, which will promote the application of additive manufacturing in producing the orthopedic implant.

This paper aims to summarize the up-to-date research performed on combinations of various biofibers and resin systems used in different three-dimensional (3D) printing technologies, including powder-based, material extrusion, solid-sheet and liquid-based systems. Detailed information about each process, including materials used and process design, are described, with the resultant products’ mechanical properties compared with those of 3D-printed parts produced from pure resin or different material combinations. In most processes introduced in this paper, biofibers are beneficial in improving the mechanical properties of 3D-printed parts and the biodegradability of the parts made using these green materials is also greatly improved. However, research on 3D printing of biofiber-reinforced composites is still far from complete, and there are still many further studies and research areas that could be explored in the future.

The paper starts with an overview of the current scenario of the composite manufacturing industry and then the problems of advanced composite materials are pointed out, followed by an introduction of biocomposites. The main body of the paper covers literature reviews of recently emerged 3D printing technologies that were applied to biofiber-reinforced composite materials. This part is classified into subsections based on the form of the starting materials used in the 3D printing process. A comprehensive conclusion is drawn at the end of the paper summarizing the findings by the authors.

Most of the biofiber-reinforced 3D-printed products exhibited improved mechanical properties than products printed using pure resin, indicating that biofibers are good replacements for synthetic ones. However, synthetic fibers are far from being completely replaced by biofibers due to several of their disadvantages including higher moisture absorbance, lower thermal stability and mechanical properties. Many studies are being performed to solve these problems, yet there are still some 3D printing technologies in which research concerning biofiber-reinforced composite parts is quite limited. This paper unveils potential research directions that would further develop 3D printing in a sustainable manner.

This paper is a summary of attempts to use biofibers as reinforcements together with different resin systems as the starting material for 3D printing processes, and most of the currently available 3D printing techniques are included herein. All of these attempts are solutions to some principal problems with current 3D printing processes such as the limit in the variety of materials and the poor mechanical performance of 3D printed parts. Various types of biofibers are involved in these studies. This paper unveils potential research directions that would further widen the use of biofibers in 3D printing in a sustainable manner.