Search results

The purpose of this paper evaluates the effects of the Great Western Development (GWD) policy on agricultural intensification, land use, agricultural production and rural poverty in western China.

The authors collect county-level data on land use, input application, grain crop production, income, poverty and geophysical characteristics for 1996–2005 and use a quasi-natural experimental design of difference-in-differences (DD) in the empirical analysis.

Results suggest that the GWD policy significantly increased the grain crop production in western China. This increase resulted from higher yield, with increased fertilizer use and agricultural electricity consumption per hectare, and more land allocated to grow grain crops. The policy also increased land-use concentration, reduced crop diversity and alleviated rural poverty in western China.

This paper makes three contributions. First, the authors add to the growing literature on the GWD policy by evaluating its effects on farm household decisions and exploring the mechanisms and broad socioeconomic impacts in western China. Second, the authors take advantage of a quasi-natural experimental design to improve the identification strategy where input use, land allocation, production and off-farm labor participation are all endogenous in a farm household. Third, the authors explore a long list of variables within one integrated dataset to present a comprehensive picture of the impact of the GWD policy.

This study aims to achieve superior localization and mapping performance in point cloud degradation scenarios through the effective removal of dynamic obstacles. With the continuous development of various technologies for autonomous vehicles, the LIDAR-based Simultaneous localization and mapping (SLAM) system is becoming increasingly important. However, in SLAM systems, effectively addressing the challenges of point cloud degradation scenarios is essential for accurate localization and mapping, with dynamic obstacle removal being a key component.

This paper proposes a method that combines adaptive feature extraction and loop closure detection algorithms to address this challenge. In the SLAM system, the ground point cloud and non-ground point cloud are separated to reduce the impact of noise. And based on the cylindrical projection image of the point cloud, the intensity features are adaptively extracted, the degradation direction is determined by the degradation factor and the intensity features are matched with the map to correct the degraded pose. Moreover, through the difference in raster distribution of the point clouds before and after two frames in the loop process, the dynamic point clouds are identified and removed, and the map is updated.

Experimental results show that the method has good performance. The absolute displacement accuracy of the laser odometer is improved by 27.1%, the relative displacement accuracy is improved by 33.5% and the relative angle accuracy is improved by 23.8% after using the adaptive intensity feature extraction method. The position error is reduced by 30% after removing the dynamic target.

Compared with LiDAR odometry and mapping algorithm, the method has greater robustness and accuracy in mapping and localization.

The purpose of this research is to develop a new slicing scheme for the emerging cooperative three-dimensional (3D) printing platform that has multiple mobile 3D printers working together on one print job.

Because the traditional lay-based slicing scheme does not work for cooperative 3D printing, a chunk-based slicing scheme is proposed to split the print job into chunks so that different mobile printers can print different chunks simultaneously without interfering with each other.

A chunk-based slicer is developed for two mobile 3D printers to work together cooperatively. A simulator environment is developed to validate the developed slicer, which shows the chunk-based slicer working effectively, and demonstrates the promise of cooperative 3D printing.

For simplicity, this research only considered the case of two mobile 3D printers working together. Future research is needed for a slicing and scheduling scheme that can work with thousands of mobile 3D printers.

The research findings in this work demonstrate a new approach to 3D printing. By enabling multiple mobile 3D printers working together, the printing speed can be significantly increased and the printing capability (for multiple materials and multiple components) can be greatly enhanced.

The chunk-based slicing algorithm is critical to the success of cooperative 3D printing, which may enable an autonomous factory equipped with a swarm of autonomous mobile 3D printers and mobile robots for autonomous manufacturing and assembly.

This work presents a new approach to 3D printing. Instead of printing layer by layer, each mobile 3D printer will print one chunk at a time, which provides the much-needed scalability for 3D printing to print large-sized object and increase the printing speed. The chunk-based approach keeps the 3D printing local and avoids the large temperature gradient and associated internal stress as the size of the print increases.

An investigation was conducted into the impact of various process parameters on the surface and subsurface quality of glass-ceramic materials, as well as the mechanism of material removal and crack formation, through the use of ultrasonic-assisted grinding.

A mathematical model of crack propagation in ultrasonic-assisted grinding was established, and the mechanism of crack formation was described through the model. A series of simulations and experiments were conducted to investigate the impact of process parameters on crack depth, surface roughness, and surface topography during ultrasonic-assisted surface and axial grinding. Additionally, the mechanism of crack formation was explored.

During ultrasonic-assisted grinding, the average grinding forces are between 0.4–1.0 N, which is much smaller than that of ordinary grinding (1.0–3.5 N). In surface grinding, the maximum surface stresses between the workpiece and the tool gradually decrease with the tool speed. The surface stresses of the workpiece increase with the grinding depth, and the depth of subsurface cracks increases with the grinding depth. With the increase of the axial grinding speed, the subsurface damage depth increases. The roughness increases from 0.780um/1.433um.

A mathematical model of crack propagation in ultrasonic-assisted grinding was established, and the mechanism of crack formation was described through the model. The deformation involved in the grinding process is large, and the FEM-SPH modeling method is used to solve the problem that the results of the traditional finite element method are not convergent and the calculation efficiency is low.

The purpose of this paper is to prepare novel electroactive shape memory nanocomposites based on graphene and study the thermomechanical property and shape memory behavior of nanocomposites.

Graphene was dispersed in N,N-dimethylformamide, and the mixture was spooned into epoxy-cyanate ester mixtures to form graphene/epoxy-cyanate ester nanocomposites. The nanocomposites were deformed under 150°C, and shape recovery test was conducted under an electric voltage of 20-100 V.

Graphene is used to improve the shape recovery behavior and performance of shape-memory polymers (SMPs) for enhanced electrical actuation effectiveness. With increment of graphene content, the shape recovery speed of nanocomposites increases significantly.

A simple way for fabricating electro-activated SMP nanocomposites has been developed by using graphene.

The outcome of this study will help to fabricate the SMP nanocomposites with high electrical actuation effectiveness and improve the shape recovery speed of the nanocomposites.

The purpose of this paper is to study the influence of calcium sulfate whiskers (CSWs) on the thermodynamic properties and shape memory properties of epoxy/cyanate ester shape memory composites.

To improve the mechanical properties of shape memory cyanate ester (CE)/epoxy polymer (EP) resin, high performance CSWs were used to reinforce the thermo-induced shape memory CE/EP composites and the shape memory CSW/CE/EP composites were prepared by molding. The effect of CSW on the mechanical properties and shape memory behavior of shape memory CE/EP composites was investigated.

After CSW filled the shape memory CE/EP composites, the bending strength of the composites is greatly improved. When the content of CSW is 5 Wt.%, the bending strength of the composite is 107 MPa and the bending strength is increased by 29 per cent compared with bulk CE/EP resin. The glass transition temperature and storage modulus of the composites were improved in CE/EP resin curing system. However, when the content of CSW is more than 10 Wt.%, clusters are easily formed between whiskers and the voids between whiskers and matrix increase, which will lead to the decrease of mechanical properties of composites. The results of shape memory test show that the shape memory recovery time of the composites decreases with the decrease of CSW content at the same temperature. In addition, the shape recovery ratio of the composites decreased slightly with the increase of the number of thermo-induced shape memory cycles.

A simple way for fabricating thermo-activated SMP composites has been developed by using CSW.

The outcome of this study will help to fabricate the SMP composites with high mechanical properties and the shape memory CSW/CE/EP composites are expected to be used in space deployable structures.

With the rapid development of China’s urbanisation and market economy, municipal solid waste (MSW) generation is increasing dramatically. In response to the threat of environmental pollution and the potential value of converting waste into energy, both the government and the public are now paying more attention to MSW treatment and disposal methods. In 2014, 178.6 million tonnes of MSW was collected at a safe treatment rate of 84.8%. However, the treatment methods and the composition of MSW are influenced by the collection area, its gross domestic product, population, rainfall and living conditions. This chapter analysed the MSW composition properties of Lhasa, Tibet, compared with other cities, such as Beijing, Guangzhou and so forth. The research showed that the moisture content of MSW in Lhasa approaches 31%, which is much lower than the other cities mentioned previously. The proportion of paper and plastics (rubbers) collected was 25.67% and 19.1%, respectively. This was 1.00–3.17 times and 0.75–2.44 times more than those found in Beijing and Guangzhou, respectively. Non-combustibles can reach up to 22.5%, which was 4.03–9.11 times that of Beijing and Guangzhou, respectively. The net heating values could reach up to 6,616 kilojoule/kilogram. The food residue was only half the proportion found in other cities. Moreover, the disposal method applied in each city has also been studied and compared.

The purpose of this paper is to investigate the effect of pulsed magnetic field (PMF) with different duty cycles on the melt flow and heat transfer behaviors during direct-chill (DC) casting of large-size magnesium alloy billet and find the appropriate range of duty cycle.

A transient two-dimensional mathematical model coupled electromagnetic field, flow field and thermal field, is conducted to study the melt flow and temperature field under PMF and compared with that under the harmonic magnetic field.

The results reveal that melt vibration and fluctuation are generated due to the instantaneous impact of repeated thrust and pull effects of Lorentz force under PMF. The peak of Lorentz force decreases greatly with the increasing duty cycle, but the melt fluctuation region is expanded with higher duty cycle, which accelerates the interior melt velocity and reduces the temperature gradient at the liquid-solid interface. However, PMF with overly high duty cycle has adverse effect on the melt convection and limited influence on the interior melt. A duty cycle of 20% to 50% is a reasonable range.

This paper can provide guiding significance for the setting of duty cycle parameters on DC casting under PMF.

There are few reports on the effect of PMF parameters during DC casting with applying PMF, especially for duty cycle, a parameter unique to PMF. The findings will be helpful for applying the external field of PMF on DC casting.

Laser cladding has been used in the field of repairing damaged parts of machine tools due to its advantages of less processing restrictions and easy formation of a good metallurgical bond with the base material. However, the mechanical properties of the coating sometimes cannot meet the process requirements. Therefore, the purpose of this paper is to prepare coatings with high microhardness and flexural strength.

The YCF102 alloy powder was mixed with different contents of Co and tested for laser cladding on AISI 1045 substrate under the same process parameters. The main phase composition of the coating was revealed by the XRD results. The main chemical composition of the coating was determined by the SEM and EDS results. In addition, the effect of Co content on the microstructure, microhardness and flexural strength of the coatings was investigated.

The results show that when the Co content is 2 wt% and 4 wt%, Co does not form compounds with other elements, but is uniformly distributed in the coating. And when the Co content is 6 wt% and 8 wt%, the Co reacts with Fe in the coating and generates Co₃Fe₇ in situ. The increase in Co did not result in a monotonic change in microhardness, but significantly improved the flexural strength and the flatness of the microstructure of the coating. When the Co content of the mixed powder is 8 wt%, the coating has high microhardness and flexural strength.

Co/YCF102 composite coating with high microhardness and flexural strength was prepared. This paper provides a theoretical and practical basis for research in the area of repairing damaged parts of machine tools by laser cladding.