Search results

Laser cladding has been used in the field of repairing damaged parts of machine tools due to its advantages of less processing restrictions and easy formation of a good metallurgical bond with the base material. However, the mechanical properties of the coating sometimes cannot meet the process requirements. Therefore, the purpose of this paper is to prepare coatings with high microhardness and flexural strength.

The YCF102 alloy powder was mixed with different contents of Co and tested for laser cladding on AISI 1045 substrate under the same process parameters. The main phase composition of the coating was revealed by the XRD results. The main chemical composition of the coating was determined by the SEM and EDS results. In addition, the effect of Co content on the microstructure, microhardness and flexural strength of the coatings was investigated.

The results show that when the Co content is 2 wt% and 4 wt%, Co does not form compounds with other elements, but is uniformly distributed in the coating. And when the Co content is 6 wt% and 8 wt%, the Co reacts with Fe in the coating and generates Co₃Fe₇ in situ. The increase in Co did not result in a monotonic change in microhardness, but significantly improved the flexural strength and the flatness of the microstructure of the coating. When the Co content of the mixed powder is 8 wt%, the coating has high microhardness and flexural strength.

Co/YCF102 composite coating with high microhardness and flexural strength was prepared. This paper provides a theoretical and practical basis for research in the area of repairing damaged parts of machine tools by laser cladding.

The “Snap back” problem of the micro‐cantilever remains one of the dominant failure mechanisms in the Micro Electro‐mechanical System (MEMS). By analyzing the Hamaker micro continuum medium and solid physics principle, the consistency model of Wigner‐Seitz (W‐S) continuum medium is presented. The gap revision coefficients of the body with the face‐centered cubic structure are derived, which include the attractive force and the repulsive one. The adhesion model of the 500 µ m X 1 µ m silicon micro‐cantilever coated by Au is established. The micro‐cantilever static relationship between the elastic force and the adhesion force is discussed. The reason of the microcantilever “snap back” problem, an instable balanced point, is discovered. Increasing the rigidity of the micro‐cantilever, a method to avoid the micro‐cantilever “snap back” to happen, is put forward, which improves MEMS structure design and enhances MEMS reliability.

Structural stress and strain in the key components of aircraft structure is important for structural health monitoring and strength assessment. However, the measure of dynamic strain is often difficult to implement because of the complex test equipment and inconvenient measure points, especially in flight test. This study aims to propose an algorithm of dynamic strain estimation using the acceleration response in time domain to simplify the measure of dynamic strain.

The relationship between the strain and acceleration response is established through the sinusoidal response or modal analysis, which is insensitive to the excitation position and form. A band-pass filter is used to obtain the modal acceleration response, and a filter frequency band selection method is proposed. Then, the dynamic strain at the concerned points can be estimated based on the modal superposition principle.

Simulation and experiment are implemented to validate the applicability and effectiveness of the strain estimation method. The estimated strain results agree well with numerical simulation as well as the experimental results. The simplicity and accuracy of the strain estimation method show practicability for dynamic strength and fatigue analysis in engineering applications.

An algorithm of dynamic strain estimation using the acceleration response in time domain is developed. A band-pass filter is used to obtain the modal acceleration response, and a filter frequency band selection method is proposed. The dynamic strain at the concerned points can be estimated based on the modal superposition principle.

The purpose of this paper is to prepare novel electroactive shape memory nanocomposites based on graphene and study the thermomechanical property and shape memory behavior of nanocomposites.

Graphene was dispersed in N,N-dimethylformamide, and the mixture was spooned into epoxy-cyanate ester mixtures to form graphene/epoxy-cyanate ester nanocomposites. The nanocomposites were deformed under 150°C, and shape recovery test was conducted under an electric voltage of 20-100 V.

Graphene is used to improve the shape recovery behavior and performance of shape-memory polymers (SMPs) for enhanced electrical actuation effectiveness. With increment of graphene content, the shape recovery speed of nanocomposites increases significantly.

A simple way for fabricating electro-activated SMP nanocomposites has been developed by using graphene.

The outcome of this study will help to fabricate the SMP nanocomposites with high electrical actuation effectiveness and improve the shape recovery speed of the nanocomposites.

In the design of anisotropic materials, such as advanced fibre‐reinforced composites, the failure envelope has a crucial role. A geometrical representation of the envelope is of particular value to investigate the highly anisotropic nature of the strength of the material. This provides the design engineer with a visualization of the failure envelope by graphically representing it using a CAD package. Use is made of both stress‐based and strain‐based polynomial failure criteria and examples are given of changes in the failure envelope due to changes in fibre orientation for a high strength graphite/epoxy composite lamina.

This study aims to achieve superior localization and mapping performance in point cloud degradation scenarios through the effective removal of dynamic obstacles. With the continuous development of various technologies for autonomous vehicles, the LIDAR-based Simultaneous localization and mapping (SLAM) system is becoming increasingly important. However, in SLAM systems, effectively addressing the challenges of point cloud degradation scenarios is essential for accurate localization and mapping, with dynamic obstacle removal being a key component.

This paper proposes a method that combines adaptive feature extraction and loop closure detection algorithms to address this challenge. In the SLAM system, the ground point cloud and non-ground point cloud are separated to reduce the impact of noise. And based on the cylindrical projection image of the point cloud, the intensity features are adaptively extracted, the degradation direction is determined by the degradation factor and the intensity features are matched with the map to correct the degraded pose. Moreover, through the difference in raster distribution of the point clouds before and after two frames in the loop process, the dynamic point clouds are identified and removed, and the map is updated.

Experimental results show that the method has good performance. The absolute displacement accuracy of the laser odometer is improved by 27.1%, the relative displacement accuracy is improved by 33.5% and the relative angle accuracy is improved by 23.8% after using the adaptive intensity feature extraction method. The position error is reduced by 30% after removing the dynamic target.

Compared with LiDAR odometry and mapping algorithm, the method has greater robustness and accuracy in mapping and localization.

The purpose of this paper is to examine and compare the influence of age, education, income, product involvement and sales promotion (SP) characteristics on consumer attitudes towards SP across eight culturally dissimilar environments.

A multi-country mall intercept and mail survey was conducted in Brunei, China, Hong Kong, Indonesia, Malaysia, New Zealand, Singapore and Thailand (n=4,125 respondents).

Country, education level and income significantly influence consumer attitudes towards SP. Some countries show a significant monetary value interaction effect. Consumers using delayed-reward SPT reported a significantly more positive attitude towards SP. Discounts and coupons are the two most highly ranked SP across the sampled countries.

Limitations include the use of intercept and mail sampling. Extending the study to include additional Asian countries and other regions would benefit the understanding of cultural influences on SP.

Multinational marketing managers should consider three aspects of SP implementation strategy: cultural and demographic factors, interaction between delayed-reward SP and socio-demographics variables; country specific SP preferences to promote both sales and brand equity.

This study investigates and extends research on SP across cultures. In particular the research helps better understand the impact of demographic factors and culture on attitudes towards SP, and implementation of global promotions.

With the rapid development of China’s urbanisation and market economy, municipal solid waste (MSW) generation is increasing dramatically. In response to the threat of environmental pollution and the potential value of converting waste into energy, both the government and the public are now paying more attention to MSW treatment and disposal methods. In 2014, 178.6 million tonnes of MSW was collected at a safe treatment rate of 84.8%. However, the treatment methods and the composition of MSW are influenced by the collection area, its gross domestic product, population, rainfall and living conditions. This chapter analysed the MSW composition properties of Lhasa, Tibet, compared with other cities, such as Beijing, Guangzhou and so forth. The research showed that the moisture content of MSW in Lhasa approaches 31%, which is much lower than the other cities mentioned previously. The proportion of paper and plastics (rubbers) collected was 25.67% and 19.1%, respectively. This was 1.00–3.17 times and 0.75–2.44 times more than those found in Beijing and Guangzhou, respectively. Non-combustibles can reach up to 22.5%, which was 4.03–9.11 times that of Beijing and Guangzhou, respectively. The net heating values could reach up to 6,616 kilojoule/kilogram. The food residue was only half the proportion found in other cities. Moreover, the disposal method applied in each city has also been studied and compared.

The purpose of this study is to identify key performance indicators (KPIs) for badminton halls and, through a case study, illustrate how the facilities performance of a university badminton hall can be evaluated from the user perspective.

After a desktop literature review, the findings were discussed by a focus group, and the discussion result formed the basis for establishing an analytic hierarchy of facilities performance for the badminton hall. Then, interviews were made with 169 badminton hall users to solicit their perceived facilities’ importance and performance levels of the hall. Using MATLAB, a computer program incorporated with an Analytic Hierarchy Process was devised to compute the importance weights of the performance attributes under assessment. The outcomes were interpreted using an importance-performance evaluation matrix.

A facilities performance hierarchy, comprising nine KPIs, was established for the badminton hall. The factors influencing the users’ perceptions, the importance and performance levels of the KPIs and the areas of the hall requiring improvements were identified.

Future studies can take a similar approach of this study to develop KPIs and facilities performance hierarchies for other types of sports venues.

The method used to identify the improvements required for the badminton hall can be applied to investigations on other sports facilities.

The methodology of this research was first applied to study a badminton hall – as reported in this paper.