Search results

1 – 10 of over 2000
Per page
102050
Citations:
Loading...
Access Restricted. View access options
Article
Publication date: 1 February 1989

W.G. Curtin

Brickwork has been around for some 4,000 years and its durability, strength and other good qualities are well known. It is a useful structural material — but limited to…

68

Abstract

Brickwork has been around for some 4,000 years and its durability, strength and other good qualities are well known. It is a useful structural material — but limited to applications where there is relatively high compressive vertical loading and relatively low horizontal loading. (A brick wall can carry a high vertical load but it can be pushed over relatively easily.) This is because brickwork, like concrete, is weak in tension. Its tensile strength in bending is less than five per cent of its compressive strength. Again, like concrete, it can either be reinforced with steel to carry the tensile stress or prestressed to eliminate the tension.

Details

Structural Survey, vol. 7 no. 2
Type: Research Article
ISSN: 0263-080X

Access Restricted. View access options
Article
Publication date: 1 March 1984

W.G. Curtin

Introduction The Victorian engineers built literally miles of mass brickwork retaining walls. Such walls relied on their dead weight to resist the overturning forces and tensile…

167

Abstract

Introduction The Victorian engineers built literally miles of mass brickwork retaining walls. Such walls relied on their dead weight to resist the overturning forces and tensile stresses caused by the retained earth, or other material. But the walls were of relatively massive thickness, under‐exploited brick‐work's compressive strength, and were structurally restricted by brickwork's low tensile strength. The advent of the more cost‐effective reinforced concrete walls saw their vitual eclipse. Reinforcing the brickwork could result in a come‐back.

Details

Structural Survey, vol. 2 no. 3
Type: Research Article
ISSN: 0263-080X

Access Restricted. View access options
Article
Publication date: 1 January 1984

John Morton

Architects and engineers are turning to structural masonry more and more today to provide the solutions for their building needs. Over the past ten years or so a growing awareness…

117

Abstract

Architects and engineers are turning to structural masonry more and more today to provide the solutions for their building needs. Over the past ten years or so a growing awareness of the use of masonry and a growing interest in designing in brickwork has been a discernable trend in the construction world. This article discusses structural masonry from three points of view. Firstly, it looks at the use of structural brickwork in Britain today — while this is predominantly unreinforced, reinforced brickwork is also discussed. Secondly, the article looks at some areas of design which, considered at the design stage, may avoid possible problems in the future. Finally, workmanship factors — which affect the structural performance of the completed building — are discussed.

Details

Structural Survey, vol. 2 no. 1
Type: Research Article
ISSN: 0263-080X

Access Restricted. View access options
Article
Publication date: 1 September 1981

American Airlines Training Ltd., a British subsidiary of American Airlines Training Corporation, opened its new £15 million Flight Training Centre near Gatwick Airport on July 21.

31

Abstract

American Airlines Training Ltd., a British subsidiary of American Airlines Training Corporation, opened its new £15 million Flight Training Centre near Gatwick Airport on July 21.

Details

Aircraft Engineering and Aerospace Technology, vol. 53 no. 9
Type: Research Article
ISSN: 0002-2667

Access Restricted. View access options
Article
Publication date: 1 March 1987

P.H. Pitt

In my last paper on the subject of PRC houses for Structural Survey (3/3 246), I described the provisions of the Housing Defects Act 1984 and the way in which it was expected to…

112

Abstract

In my last paper on the subject of PRC houses for Structural Survey (3/3 246), I described the provisions of the Housing Defects Act 1984 and the way in which it was expected to work. Under that Act, the Secretary of State named 28 types of PRC houses to which repairs could be carried out with the benefit of grants payable by the Government.

Details

Structural Survey, vol. 5 no. 3
Type: Research Article
ISSN: 0263-080X

Access Restricted. View access options
Article
Publication date: 25 September 2024

Djeffal Mohamed, Merdas Abdelghani and Douara Taha Hocine

Although the reinforcement of concrete and brick masonry with fiber-reinforced polymer (FRP) has been extensively researched, its application and impact on natural stone…

14

Abstract

Purpose

Although the reinforcement of concrete and brick masonry with fiber-reinforced polymer (FRP) has been extensively researched, its application and impact on natural stone, especially in historic preservation, have received less attention. This study aims to examine the bond-slip characteristics of carbon fiber-reinforced polymer (CFRP) with two types of natural stone masonry, aiming to enhance their effectiveness in reinforcing historic structures. The stones studied include one from the Chouf-Lekdad region (A) and another from a historic structure in Sétif City (B). Both stones were strengthened using CFRP and carbon fiber fabric (CFF) through near-surface mount (NSM) and external bonding (EBR) techniques.

Design/methodology/approach

The interaction was assessed during the pull-out test by analyzing the stress transfer mechanisms, adhesion and deformation. This study also examines the effects of the following parameters on the bond between CFRP and stone: type of stone (A and B), type of reinforcement (plat CFRP and CFF), various notch shapes and sizes (bp, tp and Lb), and reinforcement techniques (NSM and EBR).

Findings

This study demonstrated the practicality and effectiveness of enhancing natural stone masonry of old buildings by integrating NSM and EBR techniques with CFRP. With a bond length of 30 mm, the pull-out force correlates with the strength of the stone. This indicates the importance of stone strength in obtaining better adhesion. The CFF–resin interface is more cohesive than the CFRP plate–resin interface because the resin penetrates the flexible CFF strip, ensuring better adhesion. In contrast, the CFRP plate interface is rigid and smooth. The results suggest that natural stone–CFRP adhesion is more effective than CFRP bonded to concrete and brick masonry due to the stone's strong resistance.

Originality/value

This experimental investigation provides new study into the bond-slip behavior of CFRP-reinforced natural stone masonry, filling the gap in existing research. The findings offer useful direction for creating FRP strengthening solutions that are specifically adapted to the properties of natural stone used in historic constructions. This study helps to improve preservation procedures by guiding the selection of reinforcing techniques, such as NSM versus EBR, and finding ideal bond lengths. This work's novelty stems from its ability to improve the structural integrity of culturally significant buildings while preserving their historical authenticity.

Details

World Journal of Engineering, vol. ahead-of-print no. ahead-of-print
Type: Research Article
ISSN: 1708-5284

Keywords

Access Restricted. View access options
Article
Publication date: 27 May 2022

Venkatesan V., Shanmugam S. and Veerappan A.R.

This paper aims to present the numerical analysis of displacements, forces and bend angles of three different structural designs of a soft actuator using the finite element…

217

Abstract

Purpose

This paper aims to present the numerical analysis of displacements, forces and bend angles of three different structural designs of a soft actuator using the finite element method. The results of this analysis help understand the physical behavior of the soft pneumatic actuator.

Design/methodology/approach

The soft actuator is designed using commercial modeling software, and the design of the actuator is analyzed using ABAQUS 19.0 with a standard implicit nonlinear analysis. There are three types of structural designs for actuators, namely, rectangular-base model, trapezoidal-base model and the trapezoidal model considered in the present study.

Findings

Maximum displacement, force and bend angle are observed in the rectangular-base model at various pressure levels.

Originality/value

The development of novel designs of the soft pneumatic actuator to undertake a comparative analysis of displacement, force and bend angle.

Details

World Journal of Engineering, vol. 20 no. 6
Type: Research Article
ISSN: 1708-5284

Keywords

Access Restricted. View access options
Article
Publication date: 5 July 2021

Venkatesan V., Shanmugam S. and Veerappan A.R.

This paper aims to study the influence of significant design parameters of elephant trunk soft pneumatic actuator and presents maximum optimized geometric structure of the…

375

Abstract

Purpose

This paper aims to study the influence of significant design parameters of elephant trunk soft pneumatic actuator and presents maximum optimized geometric structure of the actuator using finite element method.

Design/methodology/approach

Analysis of variance (ANOVA) is used to examine the influence of significant parameters such as wall thickness, bottom layer thickness and gap between adjacent chambers on the performance of the soft actuator. The most influencing parameter is found to be the wall thickness compared to the gap between adjacent chambers and bottom layer thickness.

Findings

The optimization of bending moment recommends a wall thickness of 1.5 mm, a gap between the adjacent channels of 1.5 mm and bottom layer thickness of 4 mm for the actuator. The theoretical expression of mechanical parameters is described.

Originality/value

The design optimization of elephant trunk shaped soft actuator with respect to bending angle and force analysis has not been investigated.

Details

World Journal of Engineering, vol. 19 no. 6
Type: Research Article
ISSN: 1708-5284

Keywords

Access Restricted. View access options
Book part
Publication date: 28 September 2015

Md Shah Azam

Information and communications technology (ICT) offers enormous opportunities for individuals, businesses and society. The application of ICT is equally important to economic and…

Abstract

Information and communications technology (ICT) offers enormous opportunities for individuals, businesses and society. The application of ICT is equally important to economic and non-economic activities. Researchers have increasingly focused on the adoption and use of ICT by small and medium enterprises (SMEs) as the economic development of a country is largely dependent on them. Following the success of ICT utilisation in SMEs in developed countries, many developing countries are looking to utilise the potential of the technology to develop SMEs. Past studies have shown that the contribution of ICT to the performance of SMEs is not clear and certain. Thus, it is crucial to determine the effectiveness of ICT in generating firm performance since this has implications for SMEs’ expenditure on the technology. This research examines the diffusion of ICT among SMEs with respect to the typical stages from innovation adoption to post-adoption, by analysing the actual usage of ICT and value creation. The mediating effects of integration and utilisation on SME performance are also studied. Grounded in the innovation diffusion literature, institutional theory and resource-based theory, this study has developed a comprehensive integrated research model focused on the research objectives. Following a positivist research paradigm, this study employs a mixed-method research approach. A preliminary conceptual framework is developed through an extensive literature review and is refined by results from an in-depth field study. During the field study, a total of 11 SME owners or decision-makers were interviewed. The recorded interviews were transcribed and analysed using NVivo 10 to refine the model to develop the research hypotheses. The final research model is composed of 30 first-order and five higher-order constructs which involve both reflective and formative measures. Partial least squares-based structural equation modelling (PLS-SEM) is employed to test the theoretical model with a cross-sectional data set of 282 SMEs in Bangladesh. Survey data were collected using a structured questionnaire issued to SMEs selected by applying a stratified random sampling technique. The structural equation modelling utilises a two-step procedure of data analysis. Prior to estimating the structural model, the measurement model is examined for construct validity of the study variables (i.e. convergent and discriminant validity).

The estimates show cognitive evaluation as an important antecedent for expectation which is shaped primarily by the entrepreneurs’ beliefs (perception) and also influenced by the owners’ innovativeness and culture. Culture further influences expectation. The study finds that facilitating condition, environmental pressure and country readiness are important antecedents of expectation and ICT use. The results also reveal that integration and the degree of ICT utilisation significantly affect SMEs’ performance. Surprisingly, the findings do not reveal any significant impact of ICT usage on performance which apparently suggests the possibility of the ICT productivity paradox. However, the analysis finally proves the non-existence of the paradox by demonstrating the mediating role of ICT integration and degree of utilisation explain the influence of information technology (IT) usage on firm performance which is consistent with the resource-based theory. The results suggest that the use of ICT can enhance SMEs’ performance if the technology is integrated and properly utilised. SME owners or managers, interested stakeholders and policy makers may follow the study’s outcomes and focus on ICT integration and degree of utilisation with a view to attaining superior organisational performance.

This study urges concerned business enterprises and government to look at the environmental and cultural factors with a view to achieving ICT usage success in terms of enhanced firm performance. In particular, improving organisational practices and procedures by eliminating the traditional power distance inside organisations and implementing necessary rules and regulations are important actions for managing environmental and cultural uncertainties. The application of a Bengali user interface may help to ensure the productivity of ICT use by SMEs in Bangladesh. Establishing a favourable national technology infrastructure and legal environment may contribute positively to improving the overall situation. This study also suggests some changes and modifications in the country’s existing policies and strategies. The government and policy makers should undertake mass promotional programs to disseminate information about the various uses of computers and their contribution in developing better organisational performance. Organising specialised training programs for SME capacity building may succeed in attaining the motivation for SMEs to use ICT. Ensuring easy access to the technology by providing loans, grants and subsidies is important. Various stakeholders, partners and related organisations should come forward to support government policies and priorities in order to ensure the productive use of ICT among SMEs which finally will help to foster Bangladesh’s economic development.

Details

E-Services Adoption: Processes by Firms in Developing Nations
Type: Book
ISBN: 978-1-78560-325-9

Keywords

Access Restricted. View access options
Book part
Publication date: 7 October 2015

Azizah Ahmad

The strategic management literature emphasizes the concept of business intelligence (BI) as an essential competitive tool. Yet the sustainability of the firms’ competitive…

Abstract

The strategic management literature emphasizes the concept of business intelligence (BI) as an essential competitive tool. Yet the sustainability of the firms’ competitive advantage provided by BI capability is not well researched. To fill this gap, this study attempts to develop a model for successful BI deployment and empirically examines the association between BI deployment and sustainable competitive advantage. Taking the telecommunications industry in Malaysia as a case example, the research particularly focuses on the influencing perceptions held by telecommunications decision makers and executives on factors that impact successful BI deployment. The research further investigates the relationship between successful BI deployment and sustainable competitive advantage of the telecommunications organizations. Another important aim of this study is to determine the effect of moderating factors such as organization culture, business strategy, and use of BI tools on BI deployment and the sustainability of firm’s competitive advantage.

This research uses combination of resource-based theory and diffusion of innovation (DOI) theory to examine BI success and its relationship with firm’s sustainability. The research adopts the positivist paradigm and a two-phase sequential mixed method consisting of qualitative and quantitative approaches are employed. A tentative research model is developed first based on extensive literature review. The chapter presents a qualitative field study to fine tune the initial research model. Findings from the qualitative method are also used to develop measures and instruments for the next phase of quantitative method. The study includes a survey study with sample of business analysts and decision makers in telecommunications firms and is analyzed by partial least square-based structural equation modeling.

The findings reveal that some internal resources of the organizations such as BI governance and the perceptions of BI’s characteristics influence the successful deployment of BI. Organizations that practice good BI governance with strong moral and financial support from upper management have an opportunity to realize the dream of having successful BI initiatives in place. The scope of BI governance includes providing sufficient support and commitment in BI funding and implementation, laying out proper BI infrastructure and staffing and establishing a corporate-wide policy and procedures regarding BI. The perceptions about the characteristics of BI such as its relative advantage, complexity, compatibility, and observability are also significant in ensuring BI success. The most important results of this study indicated that with BI successfully deployed, executives would use the knowledge provided for their necessary actions in sustaining the organizations’ competitive advantage in terms of economics, social, and environmental issues.

This study contributes significantly to the existing literature that will assist future BI researchers especially in achieving sustainable competitive advantage. In particular, the model will help practitioners to consider the resources that they are likely to consider when deploying BI. Finally, the applications of this study can be extended through further adaptation in other industries and various geographic contexts.

Details

Sustaining Competitive Advantage Via Business Intelligence, Knowledge Management, and System Dynamics
Type: Book
ISBN: 978-1-78441-764-2

Keywords

1 – 10 of over 2000
Per page
102050