Search results

1 – 7 of 7
Per page
102050
Citations:
Loading...
Access Restricted. View access options
Article
Publication date: 28 September 2012

J. Suwanprateeb, F. Thammarakcharoen, K. Wasoontararat and W. Suvannapruk

The purpose of this paper is to study the influence of changing printing parameters (powder layer thickness and binder saturation) in a three dimensional printing machine (3DP) on…

1378

Abstract

Purpose

The purpose of this paper is to study the influence of changing printing parameters (powder layer thickness and binder saturation) in a three dimensional printing machine (3DP) on the transformation of 3DP printed plaster of paris to hydroxyapatite by low temperature phosphorization.

Design/methodology/approach

Plaster of paris‐based powder mixture was used to print specimens using different powder layer thickness (0.080, 0.10 and 0.20 mm) and saturation ratio (1 and 2). Subsequently, density, microstructure, mechanical properties, transformation rate and phase composition were analyzed to compare the influence of such printing parameters on properties.

Findings

It was found that printing parameters strongly affect the transformation efficiency and properties of the samples. The sample printed at layer thickness of 0.10 mm and saturation ratio of 1 yielded the highest transformation rate, density and greatest flexural modulus and strength after conversion. This was related to the sufficiently low density structure with good mechanical properties of the as‐fabricated 3DP sample which was suitable for the low temperature phosphorization process. Hydroxyapatite and monetite were found to be the main phases after conversion and the content of each phase depended on the conversion time and on also the printing parameters.

Research limitations/implications

The optimal printing parameters were true for the materials used in this study. In the case of using other materials formulation, the optimal printing parameters might be different from these values.

Practical implications

The results presented here can be used as a guideline for selecting printing parameters in 3DP machine for achieving properties as desired for specific applications or post‐processing techniques.

Originality/value

The paper demonstrates the printing parameters that were needed to be considered for efficient phase transformation and high mechanical properties.

Details

Rapid Prototyping Journal, vol. 18 no. 6
Type: Research Article
ISSN: 1355-2546

Keywords

Access Restricted. View access options
Article
Publication date: 30 September 2019

Pataravit Rukskul, Waraporn Suvannapruk and Jintamai Suwanprateeb

The purpose of this study is to evaluate the intra- and post-operative performance and safety of direct three dimensional printing (3DP) porous polyethylene implants in cranial…

149

Abstract

Purpose

The purpose of this study is to evaluate the intra- and post-operative performance and safety of direct three dimensional printing (3DP) porous polyethylene implants in cranial reconstruction.

Design/methodology/approach

Prefabricated porous polyethylene implants were prepared by direct 3DP, and cranioplasty implantation was performed. Postoperative aesthetics, patient satisfaction, firmness of the implant, reactions to the implant and 3D computed tomography (CT) scanning were assessed after 2, 6, 12 and 24 months postoperatively.

Findings

No complications after surgery were encountered. Excellent aesthetic results were obtained in all cases, and all the patients were satisfied with the reconstruction outcome. Bone density structure was found to ingrowth into these direct 3DP porous polyethylene implants and the content increased with increasing follow-up times.

Research limitations/implications

This study was a pilot study conducted in a single group and evaluated in a short-term period. The bone formation and ingrowth were indirectly assessed by 3D CT evaluation.

Originality/value

This work reported the use and evaluation of direct 3DP porous polyethylene in middle- to large-sized cranial reconstructions. It evidently showed the bonding of implants to surrounding tissues which would result in the long-term stability and infection resistance of the implant.

Details

Rapid Prototyping Journal, vol. 26 no. 2
Type: Research Article
ISSN: 1355-2546

Keywords

Access Restricted. View access options

Abstract

Purpose

Additive manufacturing (AM) or solid freeform fabrication (SFF) technique is extensively used to produce intrinsic 3D structures with high accuracy. Its significant contributions in the field of tissue engineering (TE) have significantly increased in the recent years. TE is used to regenerate or repair impaired tissues which are caused by trauma, disease and injury in human body. There are a number of novel materials such as polymers, ceramics and composites, which possess immense potential for production of scaffolds. However, the major challenge is in developing those bioactive and patient-specific scaffolds, which have a required controlled design like pore architecture with good interconnectivity, optimized porosity and microstructure. Such design not only supports cell proliferation but also promotes good adhesion and differentiation. However, the traditional techniques fail to fulfill all the required specific properties in tissue scaffold. The purpose of this study is to report the review on AM techniques for the fabrication of TE scaffolds.

Design/methodology/approach

The present review paper provides a detailed analysis of the widely used AM techniques to construct tissue scaffolds using stereolithography (SLA), selective laser sintering (SLS), fused deposition modeling (FDM), binder jetting (BJ) and advanced or hybrid additive manufacturing methods.

Findings

Subsequently, this study also focuses on understanding the concepts of TE scaffolds and their characteristics, working principle of scaffolds fabrication process. Besides this, mechanical properties, characteristics of microstructure, in vitro and in vivo analysis of the fabricated scaffolds have also been discussed in detail.

Originality/value

The review paper highlights the way forward in the area of additive manufacturing applications in TE field by following a systematic review methodology.

Details

Rapid Prototyping Journal, vol. 27 no. 6
Type: Research Article
ISSN: 1355-2546

Keywords

Access Restricted. View access options
Article
Publication date: 18 May 2023

Pradeep Kumar Mishra and Jagadesh T.

The tensile behavior of additively manufactured nylon-based carbon fiber-reinforced composites (CFRP) is an important criterion in aerospace and automobile structural design. So…

346

Abstract

Purpose

The tensile behavior of additively manufactured nylon-based carbon fiber-reinforced composites (CFRP) is an important criterion in aerospace and automobile structural design. So, this study aims to evaluate and validate the tensile stiffness of printed CFRP composites (low- and high-volume fraction fiber) using the volume average stiffness (VAS) model in consonance with experimental results. In specific, the tensile characterization of printed laminate composites is studied under the influence of raster orientations and process-induced defects.

Design/methodology/approach

CFRP composite laminates of low- and high-volume fraction carbon fiber of different raster orientations (0°, ± 45° and 0/90°) were fabricated using the continuous fiber 3D printing technique, and tensile characteristics of laminates were done on a universal testing machine with the crosshead speed of 2 mm/min. The induced fracture surface of laminates due to tensile load was examined using the scanning electron microscopy technique.

Findings

The VAS model can predict the tensile stiffness of printed CFRP composites with different raster orientations at an average prediction error of 5.94% and 10.58% for low- and high-volume fiber fractions, respectively. The unidirectional CFRP laminate composite with a high-volume fraction (50%) of carbon fiber showed 50.79% more tensile stiffness and 63.12% more tensile strength than the low-volume fraction (26%) unidirectional composite. Fiber pullout, fiber fracture and ply delamination are the major failure appearances observed in fracture surfaces of laminates under tensile load using scanning electron microscopy.

Originality/value

This investigation demonstrates the novel methodology to study specific tensile characteristics of low- and high-volume fraction 3D printed CFRP composite.

Details

Rapid Prototyping Journal, vol. 29 no. 8
Type: Research Article
ISSN: 1355-2546

Keywords

Access Restricted. View access options
Article
Publication date: 11 January 2013

Christian Polzin, Sebastian Spath and Hermann Seitz

The purpose of this paper is to characterize and evaluate a new 3D‐printing process based on Poly(methyl methacrylate) (PMMA).

3982

Abstract

Purpose

The purpose of this paper is to characterize and evaluate a new 3D‐printing process based on Poly(methyl methacrylate) (PMMA).

Design/methodology/approach

A benchmark part and standard parts were designed, printed by a 3D‐printer and characterized.

Findings

3D printed PMMA parts have a tensile strength of 2.91 MPa and a modulus of elasticity of 223 MPa. The mechanical properties can be improved by infiltrations with epoxy (tensile strength: 26.6 MPa, modulus of elasticity: 1,190 MPa). The surface quality of the parts can be improved by infiltration with wax for usage as lost models. The minimum feature size is 0.3 mm.

Research limitations/implications

The PMMA‐based 3D printing process can be used for manufacturing concept models, functional parts and lost models for investment casting.

Originality/value

This is the first paper investigating a PMMA‐based 3D printing process.

Access Restricted. View access options
Article
Publication date: 18 April 2016

Han Chen and Yaoyao Fiona Zhao

Binder jetting (BJ) process is an additive manufacturing (AM) process in which powder materials are selectively joined by binder materials. Products can be manufactured…

3670

Abstract

Purpose

Binder jetting (BJ) process is an additive manufacturing (AM) process in which powder materials are selectively joined by binder materials. Products can be manufactured layer-by-layer directly from three-dimensional model data. The quality properties of the products fabricated by the BJ AM process are significantly affected by the process parameters. To improve the product quality, the optimal process parameters need to be identified and controlled. This research works with the 420 stainless steel powder material.

Design/methodology/approach

This study focuses on four key printing parameters and two end-product quality properties. Sixteen groups of orthogonal experiment designed by the Taguchi method are conducted, and then the results are converted to signal-to-noise ratios and analyzed by analysis of variance.

Findings

Five sets of optimal parameters are concluded and verified by four group confirmation tests. Finally, by taking the optimal parameters, the end-product quality properties are significantly improved.

Originality/value

These optimal parameters can be used as a guideline for selecting proper printing parameters in BJ to achieve the desired properties and help to improve the entire BJ process ability.

Access Restricted. View access options
Article
Publication date: 28 January 2021

Yashwant Kumar Modi and Kiran Kumar Sahu

This study aims to optimize the process parameters of ZPrinter® 450 for measured porosity (MP) and compressive strength (CS) of calcium sulfate-based porous bone scaffold using…

205

Abstract

Purpose

This study aims to optimize the process parameters of ZPrinter® 450 for measured porosity (MP) and compressive strength (CS) of calcium sulfate-based porous bone scaffold using Taguchi approach.

Design/methodology/approach

Initially, a porous scaffold with smallest pore size that can be de-powdered completely is identified through a pilot study. Five printing parameters, namely, layer thickness (LT), build orientation (BO), build position (BP), delay time (DT) and binder saturation (BS), each at three levels have been optimized for MP and CS of the fabricated scaffolds using L27 orthogonal array (OA), signal-to-noise ratio and analysis of variance (ANOVA).

Findings

The scaffolds with 600 µm pores could be de-powdered completely. Optimum levels of parameters are LT2, BO1, BP2, DT1 and BS1 for MP and LT1, BO1, BP2, DT1 and BS2 for CS. The ANOVA reveals that the BS (49.12%) is the most and BP (8.34%) is the least significant parameter for MP. LT (50.84%) is the most, BO (33.79%) is second most and DT (2.59%) is the least significant parameter for CS. Taguchi confirmation test and linear regression models indicate a good agreement between predicted and experimental values of MP and CS. The experimental values of MP and CS at the optimum levels of parameters are found 38.12% and 1.29 MPa, respectively.

Originality/value

The paper presents effect of process parameters of ZPrinter® 450 on MP and CS of calcium sulfate-based porous scaffolds. Results may be used as guideline for powder bed binder jetting three-dimensional printing of ceramic scaffolds.

Details

Rapid Prototyping Journal, vol. 27 no. 2
Type: Research Article
ISSN: 1355-2546

Keywords

1 – 7 of 7
Per page
102050