Search results

Ceramic three‐dimensional parts can be produced by a stereolithography (SL) process using a ceramic suspension containing alumina powder, UV curable monomer, diluent, photoinitiator and dispersant. The monomer reacts to UV radiation (argon ionized laser) and is transformed into a solid polymer which is then removed by thermal treatment (debinding). Subsequent sintering of green parts leads to dense ceramic parts. The effect of each component on the rheology of the alumina suspensions has been studied first. Both the addition of dispersant and diluent and the increase in temperature allow a significant decrease of the viscosity of the suspensions. The highly loaded (more than 55 vol. per cent), homogeneous and stable suspensions have a shear thinning behaviour which is favourable for casting the layers. Adequate cured depth (above 200μm) and satisfactory transversal resolution have been obtained and these allow the production of ceramic parts, which demonstrates the feasibility of the process. Sintering at 1,580°C leads to dense ceramic parts with homogeneous microstructure. The process still needs to be optimized to improve even more the mechanical properties.

Modern fighter aircraft using active electronically scanned array (AESA) fire control radars are able to detect and track targets at long ranges, in the order of 50 nautical miles or more. Low observable or stealth technology has contested the radar capabilities, reducing detection/tracking ranges roughly to one-third (or even less, for fighter aircraft radar). Hence, infrared search and track (IRST) systems have been reconsidered as an alternative to the radar. This study aims to explore and compare the capabilities and limitations of these two technologies, AESA radars and IRST systems, as well as their synergy through sensor fusion.

The AESA radar range is calculated with the help of the radar equation under certain assumptions, taking into account heat dissipation requirements, using the F-16 fighter as a case study. Concerning the IRST sensor, a new model is proposed for the estimation of the detection range, based on the emitted infrared radiation caused by aerodynamic heating.

The maximum detection range provided by an AESA radar could be restricted because of the increased waste heat which is produced and the relevant constraints concerning the cooling capacity of the carrying aircraft. On the other hand, IRST systems exhibit certain advantages over radars against low observable threats. IRST could be combined with a datalink with the help of data fusion, offering weapons-quality track.

An original approach is provided for the IRST detection range estimation. The AESA/IRST comparison offers valuable insight, while it allows for more efficient planning, at the military acquisition phase, as well as at the tactical level.

Successful smart cities' implementation will require organisational leadership decision-making competences. The foundation of smart cities is digital technologies; many of these technologies are emerging technologies that require IT skills, which are scarce and will exacerbate the battle for talent between organisations. Filling the talent gap will necessitate global hiring, which has implications for organisational culture, cultural diversity and organisational leadership. Organisational cultural mix is an important contributor to leadership decision-making. However, decision-making is underpinned by trust. Blockchain is an emerging technology that has the potential to engender organisational trust in decision-making and, by extension, in the leadership with the ‘right’ organisational culture. Smart cities will be required to leverage emerging technologies to give business performance a competitive advantage and use emerging technologies’ applications to build a sustainable competitive advantage.

Talent management is conducted to maximize an organization's overall performance and efficiency which helps to serve as a competitive advantage. Human resource management is a concept which includes human-related activities, but talent management is a strategy which helps to get new talent, develop their skill sets and provide better employee engagement and experience to retain the top potential employees in an organization. Improvement in recruiting and retention of a workforce results from a well-executed talent acquisition approach. In the 21st century, employee retention has become a primary concern for the organizations specially with work from home and hybrid models.

The workforce for tomorrow is going to be very different from what it has been. Technology is transforming the way people work within organizations. The workplace is rapidly evolving in terms of people and processes and is going through a lot of technological changes. The terminologies such as automation, artificial intelligence, augmented reality and block chain technologies are slowly becoming part of the workplace and everyday activities of the organization.

The challenges are many and especially post-pandemic organizations are going through some major changes such as a mindset shift of employees to take up more remote working opportunities, building virtual teams, increase in the gig economy workers (contractual workers) and a diverse workforce which makes it even more challenging for the organization to manage and retain talent.

In recent years, additive manufacturing (AM) technology has been acknowledged as an efficient method for producing geometrical complex objects with a wide range of applications. However, dimensional inaccuracies and presence of defects hinder the broad adaption of AM procedures. These factors arouse concerns regarding the quality of the products produced with AM and the utilization of quality control (QC) techniques constitutes a must to further support this emerging technology. This paper aims to assist researchers to obtain a clear sight of what are the trends and what has been inspected so far concerning non-destructive testing (NDT) QC methods in AM.

In this paper, a survey on research advances on non-destructive QC procedures used in AM technology has been conducted. The paper is organized as follows: Section 2 discusses the existing NDT methods applied for the examination of the feedstock material, i.e. incoming quality control (IQC). Section 3 outlines the inspection methods for in situ QC, while Section 4 presents the methods of NDT applied after the manufacturing process i.e. outgoing QC methods. In Section 5, statistical QC methods used in AM technologies are documented. Future trends and challenges are included in Section 6 and conclusions are drawn in Section 7.

The primary scope of the study is to present the available and reliable NDT methods applied in every AM technology and all stages of the process. Most of the developed techniques so far are concentrated mainly in the inspection of the manufactured part during and post the AM process, compared to prior to the procedure. Moreover, material extrusion, direct energy deposition and powder bed processes are the focal points of the research in NDT methods applied in AM.

This literature review paper is the first to collect the latest and the most compatible techniques to evaluate the quality of parts produced by the main AM processes prior, during and after the manufacturing procedure.

Conventional machining methods for fabricating piezoelectric components such as ultrasound transducer arrays are time-consuming and limited to relatively simple geometries. The purpose of this paper is to develop an additive manufacturing process based on the projection-based stereolithography process for the fabrication of functional piezoelectric devices including ultrasound transducers.

To overcome the challenges in fabricating viscous and low-photosensitive piezocomposite slurry, the authors developed a projection-based stereolithography process by integrating slurry tape-casting and a sliding motion design. Both green-part fabrication and post-processing processes were studied. A prototype system based on the new manufacturing process was developed for the fabrication of green-parts with complex shapes and small features. The challenges in the sintering process to achieve desired functionality were also discussed.

The presented additive manufacturing process can achieve relatively dense piezoelectric components (approximately 95 per cent). The related property testing results, including X-ray diffraction, scanning electron microscope, dielectric and ferroelectric properties as well as pulse-echo testing, show that the fabricated piezo-components have good potentials to be used in ultrasound transducers and other sensors/actuators.

A novel bottom-up projection system integrated with tape casting is presented to address the challenges in the piezo-composite fabrication, including small curing depth and viscous ceramic slurry recoating. Compared with other additive manufacturing processes, this method can achieve a thin recoating layer (as small as 10 μm) of piezo-composite slurry and can fabricate green parts using slurries with significantly higher solid loadings. After post processing, the fabricated piezoelectric components become dense and functional.

Multiview was defined in 1985 and has been since refined to become an influential approach to information systems development. It has soft and hard aspects and, as a contingency approach, is not prescriptive but adapted to the particular situation in the organization and the application. Observations and reflections on Multiview in action over the last ten years together with more recent literature based on, for example, holism, emergence, multi‐causality, ethical analysis and technology foresight, form the basis for a new definition of Multiview. Changes in the domain of information systems are also taken into account. Away from centralized technology, long lead times and hierarchical organizations, towards networks, new organizational forms, business processes, informational products and services, and the removal of time and space constraints on human activity. This paper underlines the need for IS researchers to learn about methodologies as they are used in practice (rather than as described in text books) and for methodologies to evolve in response to changes in the domain in which they are applied.

The purpose of this paper is to evaluate the properties of several thiol-acrylate photosensitive systems and compare with corresponding acrylate free-radical systems. The potential stereolithography applications of thiol–ene photosensitive systems are also discussed.

In the both thiol–ene and acrylate free-radical photosensitive systems, various key performances were characterized. The function group conversions were characterized by real-time Fourier transform infrared spectroscopy. The tension strength was determined according to the standard ASTM D638-2003, the flexible strength was determined according to ASTM D790-07 and the hardness was measured according to ASTM D2240-05. The volume shrinkage was measured by dilatometer method. The glass transition temperature was analyzed by differential scanning calorimeter.

As adding mercapto propionates into acrylate system, the inhibition of polymerization by oxygen was controlled and the flexible performance was improved. In addition, the photosensitive resin showed better tension strength, higher elongation at break and lower volume shrinkage. Among the four mercapto propionates, rigid TEMPIC showed most obvious affect, followed hexa-functional DPMP, tetra-functional PETMP and tri-functional TMMP.

Although the thiol–ene photosensitive resin has unmatched advantages in performance, there are no reports on the thiol–ene photosensitive resin in the stereolithography application. In this study, thiol–ene photopolymerization material was first tentatively implemented in stereolithography area. Several critical performance parameters were compared between thiol–ene and acrylate free-radical photosensitive systems.

The purpose of this paper is to present a hybrid manufacturing system that integrates stereolithography (SL) and direct print (DP) technologies to fabricate three‐dimensional (3D) structures with embedded electronic circuits. A detailed process was developed that enables fabrication of monolithic 3D packages with electronics without removal from the hybrid SL/DP machine during the process. Successful devices are demonstrated consisting of simple 555 timer circuits designed and fabricated in 2D (single layer of routing) and 3D (multiple layers of routing and component placement).

A hybrid SL/DP system was designed and developed using a 3D Systems SL 250/50 machine and an nScrypt micro‐dispensing pump integrated within the SL machine through orthogonally‐aligned linear translation stages. A corresponding manufacturing process was also developed using this system to fabricate 2D and 3D monolithic structures with embedded electronic circuits. The process involved part design, process planning, integrated manufacturing (including multiple starts and stops of both SL and DP and multiple intermediate processes), and post‐processing. SL provided substrate/mechanical structure manufacturing while interconnections were achieved using DP of conductive inks. Simple functional demonstrations involving 2D and 3D circuit designs were accomplished.

The 3D micro‐dispensing DP system provided control over conductive trace deposition and combined with the manufacturing flexibility of the SL machine enabled the fabrication of monolithic 3D electronic structures. To fabricate a 3D electronic device within the hybrid SL/DP machine, a process was developed that required multiple starts and stops of the SL process, removal of uncured resin from the SL substrate, insertion of active and passive electronic components, and DP and laser curing of the conductive traces. Using this process, the hybrid SL/DP technology was capable of successfully fabricating, without removal from the machine during fabrication, functional 2D and 3D 555 timer circuits packaged within SL substrates.

Results indicated that fabrication of 3D embedded electronic systems is possible using the hybrid SL/DP machine. A complete manufacturing process was developed to fabricate complex, monolithic 3D structures with electronics in a single set‐up, advancing the capabilities of additive manufacturing (AM) technologies. Although the process does not require removal of the structure from the machine during fabrication, many of the current sub‐processes are manual. As a result, further research and development on automation and optimization of many of the sub‐processes are required to enhance the overall manufacturing process.

A new methodology is presented for manufacturing non‐traditional electronic systems in arbitrary form, while achieving miniaturization and enabling rugged structure. Advanced applications are demonstrated using a semi‐automated approach to SL/DP integration. Opportunities exist to fully automate the hybrid SL/DP machine and optimize the manufacturing process for enhancing the commercial appeal for fabricating complex systems.

This work broadly demonstrates what can be achieved by integrating multiple AM technologies together for fabricating unique devices and more specifically demonstrates a hybrid SL/DP machine that can produce 3D monolithic structures with embedded electronics and printed interconnects.

The objective of this study is to investigate the use of a fibre Bragg grating (FBG) sensor for measuring of curing strains that develop during the solidification of a photocurable resin used in 3D microfabrication.

The followed approach consists of embedding a 1,300 nm FBG into a cylindrical specimen, fabricated into a transparent mould, being exposed to ultraviolet laser light. The further development of the cure induced strains under thermal treatment was also studied by post‐conditioning the cylindrical specimen in an oven at 70°C.

The experimental results demonstrate the capability of the FBG sensor to provide useful information on the strain build‐up during laser solidification and their post‐cure evolution under the presence of a thermal environment.

Future work should involve the use of smaller diameter FBG sensors in microstereolithography built parts.

It is shown that considerable cure strains are developed at the end of the photo‐polymerisation process that eventually can affect the structural resolution of final parts fabricated by microstereolithography.

The presented method can be used to investigate other photopolymers used in micro‐stereolithography.