Search results

Food loss and wastage is an issue of global concern and the household sector is one of the biggest contributors to this. Solar drying has been explored by many eminent researchers as a solution to this problem but there have been concerns about the lack in designs, higher cost, lower performance, and consumer acceptability. The present research aims to design a small-scale domestic solar dryer by using computer software.

Response surface methodology (RSM) and computational fluid dynamics (CFD) are used to design the domestic solar dryer. Initially, design variables (inlet and outlet vent height) are identified and a design of experiments has been created using RSM for set of experimental runs. The experimental runs suggested by RSM were carried out using CFD simulation in COMSOL Multiphysics software and the results were used for optimization of response variables (outlet velocity and drying chamber temperature) in RSM.

Outlet vent height was found to be most significantly affecting parameter to both the responses. The optimum values of inlet and outlet vent heights were 0.5 and 2.5 cm, respectively with the overall desirability of 0.728. The model accuracy was tested by conducting a confirmation test as post processing in design expert software.

Designing a solar dryer is a complex, costly and time consuming process, this study presents an easy, economic and fast method to design a new solar dryer. It would help researchers to design and develop new domestic as well as large size industrial solar dryer.

The purpose of this paper is to investigate an analytical modeling for the thermoelastic buckling behavior of functionally graded (FG) rectangular plates (FGM) under thermal loadings. The material properties of FGM are assumed to vary continuously through the thickness of the plate, according to the simple power-law distribution. Derivations of equations are based on novel refined theory using a new hyperbolic shear deformation theory. Unlike other theories, there are only four unknown functions involved, as compared to five in other shear deformation theories. The theory presented is variationally consistent and strongly similar to the classical plate theory in many aspects. It does not require the shear correction factor, and gives rise to the transverse shear stress variation so that the transverse shear stresses vary parabolically across the thickness to satisfy free surface conditions for the shear stress. In addition, numerical results for a variety of FG plates with simply supported edge are presented and compared with those available in the literature. Moreover, the effects of geometrical parameters of dimension the length to width aspect ratio (a/b), the plate width to thickness ratio (b/h), and material properties index (k) on the FGM buckling temperature difference are determined and discussed.

In the current paper, the application of the refined theory proposed by Shimpi is based on the assumption that the in-plane and transverse displacements consist of bending and shear components in which the bending components do not contribute toward shear forces and, likewise, the shear components do not contribute toward bending moments. The most interesting feature of this theory is that it accounts for a quadratic variation of the transverse shear strains across the thickness, and satisfies the zero traction boundary conditions on the top and bottom surfaces of the plate without using shear correction factors. It is extended to the analysis of buckling behavior of ceramic-metal FG plates subjected to the three types of thermal loadings, namely; uniform temperature rise, linear temperature change across the thickness, and nonlinear temperature change across the thickness. The material properties of the FG plates are assumed to vary continuously through the thickness of the plate, according to the simple power-law distribution. Numerical results for a variety of FG plates with simply supported edges are given and compared with the available results, wherever possible. Additionally, the effects of geometrical parameters and material properties on the buckling temperature difference of FGM plates are determined and discussed.

Unlike any other theory, the theory presented gives rise to only four governing equations. Number of unknown functions involved is only four, as against five in case of simple shear deformation theories of Mindlin and Reissner (first shear deformation theory). The plate properties are assumed to be varied through the thickness following a simple power-law distribution in terms of volume fraction of material constituents. The theory presented is variationally consistent, does not require shear correction factor, and gives rise to transverse shear stress variation such that the transverse shear stresses vary parabolically across the thickness satisfying shear stress free surface conditions.

To the best of the authors’ knowledge, there are no research works for thermal buckling analysis of FG rectangular plates based on new four-variable refined plate theory (RPT). The novelty of this paper is extended the use of the above-mentioned RPT with the addition of a new function proposed by Shimpi for thermal buckling analysis of plates made of FG materials. Unlike any other theory, the number of unknown functions involved is only four, as against five in the case of other shear deformation theories. The theory takes account of transverse shear effects and parabolic distribution of the transverse shear strains through the thickness of the plate, hence it is unnecessary to use shear correction factors. The plates subjected to the two types of thermal loadings, namely; uniform temperature rise and nonlinear temperature change across the thickness. Numerical results for a variety of FG plates with simply supported edges are given and compared with the available results.

This paper aims to present a new one-variable first-order shear deformation theory (OVFSDT) using nonlocal elasticity concepts for buckling of graphene sheets.

The FSDT had errors in its assumptions owing to the assumption of constant shear stress distribution along the thickness of the plate, even though by using the shear correction factor (SCF), it has been slightly corrected, the errors have been remained owing to the fact that the exact value of SCF has not already been accurately identified. By using two-variable first-order shear deformation theories, these errors decreased further by removing the SCF. To consider nanoscale effects on the plate, Eringen’s nonlocal elasticity theory was adopted. The critical buckling loads were computed by Navier’s approach. The obtained numerical results were then compared with previous studies’ results using molecular dynamics simulations and other plate theories for validation which also showed the accuracy and simplicity of the proposed theory.

In comparing the biaxial buckling results of the proposed theory with the two-variable shear deformation theories and exact results, it revealed that the two-variable plate theories were not appropriate for the investigation of asymmetrical analyses.

A formulation for FSDT was innovated by reconsidering its errors to improve the FSDT for investigation of mechanical behavior of nanoplates.

A new simple parametric shear deformation theory applicable to isotropic and functionally graded plates is developed. This new theory has five degrees of freedom, provides parabolic transverse shear strains across the thickness direction and hence, it does not need shear correction factor. Moreover, zero-traction boundary conditions on the top and bottom surfaces of the plate are satisfied rigorously. The paper aims to discuss these issues.

Material properties are temperature-dependent and vary continuously through the thickness according to a power law distribution. The plate is assumed to be initially stressed by a temperature rise through the thickness. The energy functional of the system is obtained using Hamilton’s principle. Free vibration frequencies are then calculated using a set of characteristic orthogonal polynomials and by applying Ritz method for different boundary conditions.

In the light of good performance of the present theory for all boundary conditions considered, it can be considered as an excellent alternative to some two-dimensional (2D) theories for approximating the tedious and time consuming three-dimensional plate problems.

To the best of the authors’ knowledge and according to literature survey, almost all published higher order shear deformation theories have been limited to simply supported boundary conditions and without taking into account the thermal stresses effects. The existing 2D shear deformation theories of Reddy, Karama and Touratier can be easily recovered. Furthermore, this feature can be highly appreciated in an iterative design process where a large number of derived plate models can be tested by selecting only two parameters in a simple polynomial function which is computationally efficient. Finally, new results are presented to show the effect of material variation, and temperature rise on natural frequencies of the FG plate for different boundary conditions.

The purpose of this paper is to study and analyse the behaviour of a magnetic fluid-based squeeze film between rotating transversely rough porous annular plates, taking the elastic deformation into consideration.

The stochastic film thickness characterizing the roughness is considered to be asymmetric with non-zero mean and variance and skewness while a magnetic fluid is taken as the lubricant. The associated stochastically averaged Reynolds-type equation is solved with appropriate boundary conditions to obtain the pressure distribution, which in turn is used to derive the expression for the load-carrying capacity.

It is observed that the roughness of the bearing surfaces affects the performance adversely, although the bearing registers an improved performance owing to the magnetic fluid lubricant. Also, it is seen that the deformation causes reduced load-carrying capacity. The bearing can support a load even in the absence of flow, unlike the case of conventional lubricants.

The originality of the paper lies in the fact that the negative effect of porosity, deformation and standard deviation can be minimized to some extent by the positive effect of the magnetic fluid lubricant in the case of negatively skewed roughness by suitably choosing the rotational inertia and aspect ratio. This effect becomes sharper when negative variance occurs.

Our study investigates the relationships between risk management systems (RMS), strategy and organizational performance. The existing research has extensively studied the effect of strategy on organizational performance. There is also a growing body of literature suggesting that RMS positively influence the achievement of organizational objectives. However, there are only a few conceptual papers (and no empirical evidence) on the relationship between strategy and RMS. We investigate whether different strategy types (defender, analyzer, prospector, and reactor) induce different levels of RMS development and, hence, affect performance indirectly, as well as directly. We use regression analysis and survey data to test the proposed relationships. Our results confirm the direct effects of strategy type and RMS development on performance. We confirm that prospectors perform better than defenders, analyzers, and reactors across five measures of performance (profitability, sales growth, market share, new product development, and customer satisfaction). We also find that companies with more developed RMS perform better in terms of non-financial performance (measured by new product development). Contrary to the prevailing evidence, we do not find significant results for financial performance. Moreover, our findings show that there is no mediating effect of RMS development in the relationship between strategy type and performance. This implies that RMS and strategy act as independent variables, each individually affecting organizational performance.

This paper introduces a closed-form solution for analyzing the buckling behavior of orthotropic plates using a refined plate theory with four variable parameters, leveraging a new hyperbolic shear displacement model.

The proposed theory incorporates a quadratic variation of transverse shear strains across the plate’s thickness and satisfies zero traction boundary conditions on both the upper and lower surfaces without employing shear correction factors. The governing equations are derived from the principle of minimum total potential energy. Closed-form solutions for rectangular plates, with two opposite edges simply supported and the remaining two edges subjected to arbitrary boundary conditions, are obtained using the state space approach to the Levy-type solution. Comparative studies are conducted to validate the accuracy of the obtained results.

The paper successfully examines and discusses in detail the effects of boundary conditions, loading conditions, variations in modulus ratio and thickness ratio on the critical buckling load of orthotropic plates.

This study presents a novel and precise method for evaluating the buckling behavior of orthotropic plates. The refined plate theory, without the need for shear correction factors, offers significant insights and improvements in understanding the critical buckling load under various conditions, contributing valuable knowledge to the field of structural analysis.

The purpose of this paper is to examine the current status of risk management in Indian companies and explore the reasons for the adoption or lack of adoption of integrated approach to risk management. It identifies the imperatives for implementation of comprehensive risk management solutions leading to enterprise‐wide risk management (EWRM). The paper shows that effective risk management can improve organizational performance but adequate infrastructure is not available in companies for implementing EWRM.

Exploratory design using the survey research methodology that includes structured questionnaires and interviews of 130 companies.

Risk management in Indian companies is currently facing the problem of integration and incentivisation. The risk management function is not suitably blended into the corporate strategy and use of information technology for risk management is minimal. The portfolio approach to risk management titled as integrated risk management or EWRM is ineffective from an implementation perspective and a sea change in risk perception is required which accentuates the need for building up of risk culture across business segments and adequate incentivisation for risk management.

Risk management is an integral part of the decision‐making process and effective risk management can proactively help in overcoming the possibilities of the business failures.

The paper highlights the fact that knowledge of risk management in Indian companies is inadequate and sample companies hesitate to respond thinking that it may reflect inefficiencies.