Kai-Uwe Garthe, Kay-Peter Hoyer, Leif Hagen, Wolfgang Tillmann and Mirko Schaper
The currently existing restrictions regarding the deployment of additively manufactured components because of poor surface roughness, porosity and residual stresses as well as…
Abstract
Purpose
The currently existing restrictions regarding the deployment of additively manufactured components because of poor surface roughness, porosity and residual stresses as well as their influence on the low-cycle fatigue (LCF) strength are addressed in this paper.
Design/methodology/approach
This study aims to evaluating the effect of different pre- and post-treatments on the LCF strength of additively manufactured 316L parts. Therefore, 316L specimens manufactured by laser powder bed fusion were examined in their as-built state as well as after grinding, or coating with regard to the surface roughness, residual stresses and LCF strength. To differentiate between topographical effects and residual stress-related phenomena, stress-relieved 316L specimens served as a reference throughout the investigations. To enable an alumina coating of the 316L components, atmospheric plasma spraying was used, and the near-surface residual stresses and the surface roughness are measured and investigated.
Findings
The results have shown that the applied pre- and post-treatments such as stress-relief heat treatment, grinding and alumina coating have each led to an increase in LCF strength of the 316L specimens. In contrast, the non-heat-treated specimens predominantly exhibited coating delamination.
Originality/value
To the best of the authors’ knowledge, this is the first study of the correlation between the LCF behavior of additively manufactured uncoated 316L specimens in comparison with additively manufactured 316L specimens with an alumina coating.
Details
Keywords
Sudipta Pramanik, Kay-Peter Hoyer and Mirko Schaper
The purpose of this study is to investigate the manufacturability of Fe-3Si lattice structures and the resulting mechanical properties. This study could lead to the successful…
Abstract
Purpose
The purpose of this study is to investigate the manufacturability of Fe-3Si lattice structures and the resulting mechanical properties. This study could lead to the successful processing of squirrel cage conductors (a lattice structure by design) of an induction motor by additive manufacturing in the future.
Design/methodology/approach
The compression behaviour of two lattice structures where struts are arranged in a face-centred cubic position and vertical edges (FCCZ), and struts are placed at body-centred cubic (BCC) positions, prepared by laser powder bed fusion (LPBF), is explored. The experimental investigations are supported by finite element method (FEM) simulations.
Findings
The FCCZ lattice structure presents a peak in the stress-strain curve, whereas the BCC lattice structure manifests a plateau. The vertical struts aligned along the compression direction lead to a significant increase in the load-carrying ability of FCCZ lattice structures compared to BCC lattice structures. This results in a peak in the stress-strain curve. However, the BCC lattice structure presents the bending of struts with diagonal struts carrying the major loads with struts near the faceplate receiving the least load. A high concentration of geometrically necessary dislocations (GNDs) near the grain boundaries along cell formation is observed in the microstructure.
Originality/value
To the best of the authors’ knowledge, this is the first study on additive manufacturing of Fe-3Si lattice structures. Currently, there are no investigations in the literature on the manufacturability and mechanical properties of Fe-3Si lattice structures.
Details
Keywords
Thomas Niendorf, Florian Brenne, Mirko Schaper, Andre Riemer, Stefan Leuders, Wilfried Reimche, Dieter Schwarze and Hans J. Maier
As additive manufacturing techniques, such as selective laser melting, allow for straightforward production of parts on basis of simple computer-aided design files only…
Abstract
Purpose
As additive manufacturing techniques, such as selective laser melting, allow for straightforward production of parts on basis of simple computer-aided design files only, unauthorized replication can be facilitated. Thus, identification and tracking of individual parts are increasingly vital in light of globalized competition. This paper aims to overcome the susceptibility of additive manufacturing techniques for product piracy by establishing a method for introducing and reading out product identification markers not visible by naked-eye inspection.
Design/methodology/approach
Lasers of different nominal power were used for altering the solidification mechanisms during processing in distinct areas of the samples. The resulting local microstructural characteristics and mechanical properties, respectively, were determined by scanning electron microscopy and hardness measurements. The applicability of an advanced eddy current technique for reading out local differences in electro-magnetic properties was examined.
Findings
The findings show that distinct microstructural features are obtained in dependence of the locally applied laser power. These features manifest themselves not only in terms of grain morphology, texture and hardness but also induce changes in the local electro-magnetic properties. The inscribed pattern can be non-destructively visualized by using an advanced eddy current technique.
Originality/value
Conventional copy protection basically consists in supplementary labelling or surface modification. In the present study, a new method is proposed for additively manufactured parts, overcoming the drawbacks of the former methods through process-induced microstructure manipulation. Slight alterations in the electro-magnetic material properties can be detected by advanced eddy current method allowing for identification of arbitrary and inimitable component information in additively manufactured parts.