Search results

A balanced armature receiver (BAR) as a special type of electromagnetic acoustic transducers plays a significant role in reproduction of music and speech, active noise control in modern hearing aid and in contemporary in-ear monitors. This paper aims to present a static analysis of the balanced armature receiver based on the lumped network approach (LNA) and the finite element method (FEM).

In this paper, the LNA and two-dimensional FEM are applied to model deflections of the BAR’s armature from the equilibrium position. Results of calculations are compared with measurements.

The derived analytical formulas and developed procedure allow for calculation of the armature deflection.

Comparing to the previous papers, the reluctance’s nonlinearity of the armature has been considered.

Electrical properties of biological tissues are known to be sensitive to physiological and pathological conditions of living organisms. For instance, human breast cancer or liver tumor cells have a significantly higher electrical conductivity than a healthy tissue. The paper aims to the new recently developed magnetoacoustic tomography with magnetic induction (MAT-MI) which can be deployed for electrical conductivity imaging of low-conductivity objects. Solving a test problem by using an analytical method is a useful exercise to check the validity of the more complex numerical finite element models. Such test problems are discussed in Chapter 3. The detailed analysis of an electromagnetic induction in low-conductivity objects is very important for the next steps in the tomographic process of image reconstruction. Finally, the image reconstruction examples for object’s complex shapes’ have been analyzed. The Lorentz force divergence reconstruction has been achieved with the help of time reversal algorithm.

In given arrangements the magnetic field and eddy current vectors satisfy the Maxwell partial differential equations. Applying the separation of variables method analytical solutions are obtained for an infinitely long conducting cylindrical segment in transient magnetic field. A special case for such a configuration is an infinitely long cylinder with longitudinal crack. The analytical solutions are compared with those obtained by using numerical procedures. For complex shapes of the object, the MAT-MI images have been calculated with the help of the finite element method and time reversal algorithm.

The finite element model developed for a MAT-MI forward problem has been validated by analytical formulas. Based on such a confirmation, the MAT-MI complex model has been defined and solved. The conditions allowing successful MAT-MI image reconstruction have been provided taking into account different conductivity distribution. For given object’s parameters, the minimum number of measuring points allowing successful reconstruction has been determined.

A simple test example has been proposed for MAT-MI forward problem. Analytical closed-form solutions have been used to check the validity of the made in-house finite element software. More complex forward and inverse problems have been solved using the software.

The purpose of this paper is to present the methodology of designing an exciter for Magnetic Induction Tomography (MIT). The design of the exciter must satisfy the following requirements: maximize MIT system sensitivity and minimize harmful influence on electronic MIT equipment.

Two objective functions are considered, namely: a magnetic flux density in the protected regions and a module of the eddy‐current density vector in the object under test in the vicinity of a sensor. The paper shows a multi‐objective optimization technique (based on the weighted sum method) which, by coupling the finite‐element method with a genetic algorithm, supports the design of the exciter.

It is possible to design in a relatively simple way an exciter for MIT under the given assumptions.

Detailed description of the multi‐objective optimization procedure has been presented.

In many different engineering fields often there is a need to protect regions from electromagnetic interference. According to static and low-frequency magnetic fields the common strategy bases on using a shield made of conductive or ferromagnetic material. Another screening technique uses solenoids that generate an opposite magnetic field to the external one. The purpose of this paper is to discuss the shielding effect for a magnetic and conducting cylindrical screen rotating in an external static magnetic field.

The magnetic flux density is expressed in terms of the magnetic vector potential. Applying the separation of variables method analytical solutions are obtained for an infinitely long magnetic conducting cylindrical screen rotating in a uniform static transverse magnetic field.

Analytical formulas of the shielding factor for a cylindrical screen of arbitrary conductivity and magnetic permeability are given. A magnetic Reynolds number is found to be an appropriate indication of the change in magnetic field inside the screen. Useful simplified expressions are presented.

This paper treats in a qualitative way the possibility of static magnetic field shielding by using rotating conducting magnetic cylindrical screens. Analytical solutions are given. If the angular velocity is equal to zero or the relative permeability of the shield is equal to one the shielding factor has forms well known from literature.

The purpose of this paper is to present the methodology of designing an exciter for magnetic induction tomography (MIT). The design of the exciter must satisfy following requirements: maximize MIT system sensitivity and minimize harmful influence on electronic MIT equipment.

Two objective functions are considered, namely: a magnetic flux density in the protected regions and a module of the eddy current density vector in the object under test in the vicinity of a sensor. The paper demonstrates a multi‐objective optimization technique (based on the ε‐constrained method) which, by coupling the finite‐element method with a genetic algorithm (GA), supports the design of the exciter.

It is possible to design in a relatively simple way an exciter for MIT under the given assumptions.

The paper is of value in presenting a detailed description of the multi‐objective optimization procedure.

The purpose of this paper is to describe the full‐wave modelling of pulsed terahertz systems utilized in non‐destructive testing.

At the outset, some basic information on the terahertz NDT are outlined and then, general remarks on its numerical modelling are presented. Frequency domain FEM and time domain FDTD analysis is carried out. Finally comparison of computed and measured signals is shown in order to prove numerical analysis correctness.

It is possible to model in a relatively simple way a terahertz system for nondestructive evaluation of dielectric materials. In contrast to other published work, the entire measuring setup is modelled, including photoconductive antenna with hemispherical lens, focusing lens and evaluated material with exemplary defect.

This paper gives a description of the terahertz non‐destructive testing system with comparison of simulated and measured results.

dc electrified traction systems are a potential source of stray currents. The purpose of this paper is to evaluate the harmful effects (electrolytic corrosion) that an electrified railway has on nearby earth return circuits (e.g. pipelines).

The electric circuit approach, based on the earth return circuit theory, to model stray currents interference on extended structures is presented. An exact method of calculation is applicable to any dc railway system in which tracks can be represented by a single earth-return circuit (equivalent rail) with current energization. In the approximate method, the equivalent rail with current energization is modeled as a large multinode electrical equivalent circuit with lumped parameters. The circuit is a chain of basic circuits, which are equivalents of homogenous sections of the rail. The electrode kinetics (polarization phenomenon) is taken into account in the model developed.

Formulas in partially closed forms are derived applicable to the analysis of currents and potentials along a pipeline laid in the proximity with railway tracks. The attempt is undertaken, to incorporate the electrode kinetics into the simulation model in which the polarization phenomenon (Tafel equation) is modeled by a non-linear voltage source with source voltage being iteratively calculated. The polarization potential along the affected pipeline can be determined.

The pipeline electrochemical response (polarization behavior – non-linear phenomenon on the interface metal-soil electrolyte) to the dc stray currents interference is innovative incorporated into the simulation model with lumped parameters using the iterative process.

Wireless power transfer (WPT) is deemed as an emerging technology with exciting applications, like wireless charging devices, and electric vehicles, whereas metamaterials exhibit exceptional properties. For every WPT system that occupies coupled magnetic resonances, it is also mandatory to involve resonators. The purpose of this paper is to introduce a new interdigitated split-ring resonator (I-SRR) as the basic part of a WPT system, pursuing advanced levels of efficiency.

A novel WPT system, which exploits I-SRRs as its elementary blocks, is comprehensively examined. The analysis investigates the distance between the modules, the distance between transmitting and receiving components as well as the geometrical features of the structure. Several numerical data derived via the finite element method unveil the merits of the featured configuration.

The proposed arrangement reveals a noteworthy enhancement of the power delivered to the load and a promising tuning of the operational frequency via the interdigitated topology. Several parametric studies clarify the principal characteristics of the proposed setup, facilitating the design of high-end systems. In particular, the distance between the resonators and the port loops affect the matching of the input and output ports, allowing optimisation of power efficiency, while the length of the I-SRR gap can determine the operational frequency.

Development of a WPT system, which utilises I-SRRs as its key elements. Incorporation of metamaterials into WPT technology. Efficiency enhancement of WPT systems and alternative design via geometrical modifications. The necessity of lumped elements to implement the WPT resonators is eliminated by utilising split-ring resonators components, enabling compactness in several implementations.