Search results

Uniform nanostructured TiO₂ thin film has been applied as an over coat on micro‐arc oxidized substrate, using the sol‐gel method. The anticorrosion performance of the coating have been evaluated using electrochemical techniques. Owing to increasing application of light alloys in industry, the purpose of this paper is to report effort to increase the corrosion and wear resistance properties of these alloys by applying a TiO₂ nanostructured coating using the sol‐gel method on the micro‐arc oxidation (MAO) surface. This approach will decrease the time for the MAO process, especially for achieving good mechanical properties, and will minimize energy consumption as well as achieving better results from the obtained coatings.

Sol‐gel coatings were deposited (on titanium substrates) by spin coating techniques. The morphologies and nanostructures of thin films were analyzed using scanning electron microscope, atomic force microscopy and grazing incidence X‐ray diffraction (XRD). The anticorrosion performance of the coating has been evaluated by using electrochemical techniques. Tafel polarization measurements provide an explanation for the increased resistance of nanostructured TiO₂ coated specimen against corrosion. Effective sol‐gel coating parameters were optimized with respect to this enhancement. Electrochemical impedance spectroscopy measurements showed the role of barrier layer on corrosion resistance of MAO and nanostructured TiO₂ coating.

The results showed that i_corr is decreased from 0.258 to 0.169 (μA/cm²). An optimized TiO₂ nanostructured coating with thickness of 74 nm will shift the open circuit potential (OCP) about 165 mV and will improve the corrosion prevention properties of coated samples. Corrosion resistance by these duplex coatings can be improved by a factor of more than three times, compared to that of the uncoated substrate. Increasing the coating thickness to more than 74 nm will decrease the physical and corrosion properties of coated samples. It can be concluded that samples with the optimized coating showed higher values of charge transfer resistance, due to the presence of a newly formed layer that accounted for the greater corrosion protection.

The results obtained in this research into nanostructured coating can be used wherever good corrosion and wear resistances are required.

The speed of treatment by this technique makes this method very suitable for industrial surface treatment of different components.

This study aims to better understand the influence of various post-treatments on the microstructure and mechanical properties of additively manufactured parts for critical applications.

In this study, Laser Powder Bed Fusion (LPBF) fabricated Inconel 718 (IN718) samples were subjected to various heat treatments, namely homogenization, solution heat treatment and double aging, to investigate their influence on the microstructure, mechanical properties and fracture mechanism at an elevated temperature of 650 °C. Homogenization treatment was performed at 1080 °C for durations ranging from 1–8 h. The solution treatment temperature varied from 980 °C to 1140 °C for 1 h, followed by double aging treatment.

At 650 °C, the as-built sample showed the minimum strength but demonstrated the maximum elongation to failure compared to the heat-treated samples. The strength of the IN718 superalloy increased by 20.26% to 34.81%, while ductility significantly reduced by 65.26% to 72.89% after various heat treatments compared to the as-built state. This change is attributed to the enhancement in grain boundary strength resulting from the pinning effect of the intergranular δ-phase.

The study observed that the variations in the fracture mechanism of LPBF fabricated IN718 depend on the duration and temperature of heat treatment. This research provides a thorough overview of the high-temperature mechanical properties of LPBF fabricated IN718 subjected to different homogenization times and solution treatment temperatures, correlating these effects to the corresponding changes in microstructure.

The purpose of this paper is to address the concern of some stainless steel users. To understand the effect of surface white spots on corrosion performance of stainless steel.

White spots appeared on some component surfaces made of 316 L stainless steel in some industrial applications. To address the concern about the pitting performance in the spot areas, the pitting corrosion potential and corrosion resistance were measured in the spot and non-spot areas by means of potentiodynamic polarization and electrochemical impedance spectroscopy and the two different surface characteristics were analytically compared by using optical microscopy, laser confocal microscopy, scanning electron microscopy, x-ray diffraction, energy dispersive spectroscopy and auger energy spectroscopy. The results indicated that the pitting performance of the 316 L stainless steel was not negatively influenced by the spots and the white spots simply resulted from the slightly different surface morphology in the spot areas.

The white spots are actually the slightly rougher surface areas with some carbon-containing species. They do not reduce the pitting resistance. Interestingly, the white spot areas even have slightly improved general corrosion resistance.

Not all surface contamination or roughening can adversely affect the corrosion resistance of stainless steel.

Stainless steel components with such surface white spots are still qualified products in terms of corrosion performance.

The surface spot of stainless steel was systematically investigated for the first time for its effect on corrosion resistance and the conclusion was new to the common knowledge.

The purpose of this paper is to extract electrochemical reaction kinetics parameters, such as Tafel slope, exchange current density and equilibrium potential, which cannot be directly measured, this study aims to propose an improved particle swarm optimization (PSO) algorithm.

In traditional PSO algorithms, each particle’s historical optimal solution is compared with the global optimal solution in each iteration step, and the optimal solution is replaced with a certain probability to achieve the goal of jumping out of the local optimum. However, this will to some extent undermine the (true) optimal solution. In view of this, this study has improved the traditional algorithm: at each iteration of each particle, the historical optimal solution is not compared with the global optimal solution. Instead, after all particles have iterated, the optimal solution is selected and compared with the global optimal solution and then the optimal solution is replaced with a certain probability. This to some extent protects the global optimal solution.

The polarization curve plotted by this equation is in good agreement with the experimental values, which demonstrates the reliability of this algorithm and provides a new method for measuring electrochemical parameters.

This study has improved the traditional method, which has high accuracy and can provide great support for corrosion research.

This paper aims to examine dissimilar joints for various applications in chemical, petrochemical, oil, gas, shipbuilding, defense, rail and nuclear industry.

This study examined the effects of cold metal transfer welding on stainless steel welds for 316L austenitic and 430 ferritic dissimilar welds with ER316L, ER309L and without (autogenous) fillers. The microstructural observation was done with an optical microscope. The mechanical test was done to reveal the strength, hardness and toughness of the joint. The electrochemical polarization tests were done to reveal intergranular and pitting corrosion in the dissimilar joints.

This microstructural study shows the presence of austenitic and ferritic phases with vermicular ferrite for ER309L filler weld, and for ER316L filler weld specimen shows predominately martensitic phase in the weld region, whereas the autogenous weld shows lathy ferrite mixed with martensitic phase. Mechanical test results indicated that filler welded specimen (ER316L and ER309L) has relatively higher strength and hardness than the autogenous weld, whereas ER316L filler weld exhibited the highest impact toughness than ER309L filler weld and lowest in autogenous weld. The electrochemical corrosion results displayed the highest degree of sensitization (DOS) in without filler welded specimen (45.62%) and lower in case of filler welded specimen ER309L (4.95%) and least in case of ER316L filler welded specimen (3.51%). The high DOS in non-filler welded specimen is correlated with the chromium carbide formation. The non-filler welded specimen shows the highest pitting corrosion attack as compared to the ER316L filler weld specimen and relatively better in ER309L filler welded specimen. The highest pitting corrosion resistance is related with the high chromium content in ER309L composition.

This experimental study is original and conducted with 316L and 430 stainless steel with ER316L, ER309 and without fillers, which will help the oil, shipbuilding and chemical industries.

The purpose of this paper is to prepare composite micro-arc oxide coatings with better wear resistance and corrosion resistance.

A nickel powder composite micro-arc oxide film was prepared on the surface of the magnesium alloy by the method of organically combining ultra-fine Ni powder with micro arc oxidation film layer. In this experiment, the changes in the corrosion resistance and microstructure of the composite film layer after adding Ni powder were studied, and the effect of the addition of glycerin on the corrosion resistance of the film layer was analyzed.

The results show that the ultra-fine nickel powder was successfully prepared by the liquid phase reduction method, and the micro-arc oxidation process was modified under the optimal addition amount. The surface of the micro-arc oxide film made of ultra-fine nickel powder was found by SEM to have smooth surfaces and few holes. According to X-ray diffraction analysis, the phase composition of the micro-arc oxide film layer was Mg, Ni, NiSiO₄, MgNi (SiO₄) and Mg₂SiO₄. According to the results of electrochemical tests, the corrosion resistance of the micro-arc oxidation composite film layer was improved after the addition of ultra-fine Ni powder, the corrosion current was greatly reduced and the impedance has been improved. And after adding glycerin, the surface of the film layer becomes denser, and the corrosion resistance of the micro-arc oxide film is significantly improved.

Through this experimental research, a micro-arc oxide coating of powder composite magnesium alloy was successfully prepared. The corrosion resistance of the micro-arc oxidation film layer has been improved, and certain functions had been given to the micro-arc oxidation composite film, which has increased the application field of magnesium alloys.

The purpose of this paper is to investigate the effect of plasma electrolytic oxidation (PEO) coatings and sealed PEO coatings on the corrosion resistance and cytocompatibility of a novel Mg-1Zn-0.45Ca alloy in simulated body fluid (SBF).

The microstructure, corrosion resistance and cytocompatibility of PEO coatings and phosphate conversion-treated PEO coatings were investigated and was compared with the bare Mg alloy.

The hot-extruded Mg-Zn-Ca alloy exhibit inhomogeneous microstructure and suffered from localized corrosion in the SBF. The PEO coating after phosphate conversion treatment offers enhanced protectiveness to the Mg alloy within an immersion period of up to 60 days, which is significantly improved compared with the performance of the PEO-coated Mg alloy, but the cytocompatibility was slightly decreased.

This work offers new perspective in balancing the protectiveness and cytocompatibility of bio-materials.

This study aims to discuss the influences of surface severe plastic deformation (S²PD) on the electrochemical corrosion, pitting corrosion, intergranular corrosion, stress corrosion cracking of aluminum (Al) alloys and attempt to correlate the microstructural/compositional changes with the performances.

This study provides a novel gradient design of structure/composition caused by S²PD for the purpose of enhancing Al alloys’ corrosion resistance.

S²PD has a significant effect on corrosion behavior of Al alloys through tuning the grain size, residual stress, composition, grain boundary phase and second phase particle distribution.

Although Al alloys are known to form a protective Al₂O₃ film, corrosion is a major challenge for the longevity of Al structures across numerous industries, especially for the infrastructures made of high-strength Al alloys. Traditional strategies of improving corrosion resistance of Al alloys heavily relied on alloying and coatings. In this review, gradient design of structure/composition caused by S²PD provides a novel strategy for corrosion protection of Al alloys, especially in the enhancement of localized corrosion resistance.

The effect of processing parameters on the microstructure of steel produced by laser-based powder bed fusion (LPBF) is a recognized opportunity for property design through microstructure control. Because the LPBF generates a textured microstructure associated with high anisotropy, it is of interest to determine the fabrication plane that would generate the desired property distribution within a component.

The microstructure of 316 L produced by LPBF was characterized experimentally (optical, scanning electron microscopy, glow discharge emission spectrometry and X-ray diffraction), and a finite element method was used to study the microstructure features of grain diameter, grain orientation and thermal parameters of cooling rate, thermal gradient and molten pool dimensions.

The computational tool of Ansys Additive was found efficient in reproducing the experimental effect of varying laser power, scanning speed and hatch spacing on the microstructure. In particular, the conditions for obtaining maximum densification and minimum fusion defects were consistent with the experiment, and the features of higher microhardness near the component’s surface and distribution of surface roughness were also reproduced.

To the best of the author’s knowledge, this paper is believed to be the first systematic attempt to use Ansys Additive to investigate the anisotropy of the 316 L SS produced by LPBF.

The purpose of this paper was to prepare the cerium-based conversion coating on AZ91D magnesium alloy, and its compositions, micro-morphology, corrosion resistance and the chemical valence state of the film elements were investigated.

The methodology comprised preparation of coatings at different temperatures, which then were characterized using scanning electron microscopy coupled with energy dispersive X-ray spectroscopy, an electrochemistry workstation and by means of X-ray photoelectron spectroscopy.

The conversion coating had a micro-cracked morphology. The conversion coatings were composed of MgO (or Mg-OH), CeO₂ and Ce2O₃. The best corrosion resistance of the cerium passivation film appeared when the treatment temperature was about 35°C.

The corrosion current densities of conversion coatings were lower by one to two orders of magnitude than the corrosion current density of the blank sample. The rare earth passivation coating prepared under the best condition could reduce the corrosion current to 3.548 × 10−6 A/cm2.