Search results

Multi-jet deposition of the materials is a matured technology used for graphic printing and 3 D printing for a wide range of materials. The multi-jet technology is fine-tuned for liquids with a specific range of viscosity and surface tension. However, the use of multi-jet for low viscosity fluids like water is not very popular. This paper aims to demonstrate the technique, particularly for the water-ice 3 D printing. 3 D printed ice parts can be used as patterns for investment casting, templates for microfluidic channel fabrication, support material for polymer 3 D printing, etc.

Multi-jet ice 3 D printing is a novel technique for producing ice parts by selective deposition and freezing water layers. The paper confers the design, embodiment and integration of various subsystems of multi-jet ice 3 D printer. The outcomes of the machine trials are reported as case studies with elaborate details.

The prismatic geometries are realized by ice 3 D printing. The accuracy of 0.1 mm is found in the build direction. The part height tends to increase due to volumetric expansion during the phase change.

The present paper gives a novel architecture of the ice 3 D printer that produces the ice parts with good accuracy. The potential applications of the process are deliberated in this paper.

In additive manufacturing (AM) process, the physical properties of the products made by fractal toolpaths are better as compared to those made by conventional toolpaths. Also, it is desirable to minimize the number of tool retractions. The purpose of this study is to describe three different methods to generate fractal-based computer numerical control (CNC) toolpath for area filling of a closed curve with minimum or zero tool retractions.

This work describes three different methods to generate fractal-based CNC toolpath for area filling of a closed curve with minimum or zero tool retractions. In the first method, a large fractal square is placed over the outer boundary and then rest of the unwanted curve is trimmed out. To reduce the number of retractions, ends of the trimmed toolpath are connected in such a way that overlapping within the existing toolpath is avoided. In the second method, the trimming of the fractal is similar to the first method but the ends of trimmed toolpath are connected such that the overlapping is found at the boundaries only. The toolpath in the third method is a combination of fractal and zigzag curves. This toolpath is capable of filling a given connected area in a single pass without any tool retraction and toolpath overlap within a tolerance value equal to stepover of the toolpath.

The generated toolpath has several applications in AM and constant Z-height surface finishing. Experiments have been performed to verify the toolpath by depositing material by hybrid layered manufacturing process.

Third toolpath method is suitable for the hybrid layered manufacturing process only because the toolpath overlapping tolerance may not be enough for other AM processes.

Development of a CNC toolpath for AM specifically hybrid layered manufacturing which can completely fill any arbitrary connected area in single pass while maintaining a constant stepover.

The support structures of sacrificial material are built in deposition-based additive manufacturing (AM), which are later removed either by breaking or dissolving. Such a sacrificial material is not feasible in metal AM. The purpose of this study is to find a suitable method for eliminating the need of support mechanism. In this work, the authors use the tilting of the substrate to alleviate the need for the support mechanism altogether.

As in the traditional AM, the object is grown in horizontal layers. However, wherever undercuts are encountered, the substrate is tilted appropriately to capture the droplets. Such a tilt involves two rotary axes invariably. To conform to the slice geometry, these two tilts are accompanied by the three linear movements. Thus, the object with undercuts is grown in planar layers using five-axis deposition without any support structure. Each pair of the corresponding top and bottom contours of any slice defines a ruled surface. The axis of the deposition head will be aligned with the rules of this surface.

The need for the support mechanism was eliminated using five-axis deposition. This was experimentally demonstrated by building an aluminum impeller using a metal inert gas cladding head.

In the proposed methodology, the objects with an abrupt change in the geometry are not possible to realize.

This manuscript proposed a novel method of eliminating the support mechanism through continuous five-axis deposition.

Additive manufacturing (AM) is a layer-by-layer technique that helps to create physical objects from a three-dimensional data set. Fused deposition modeling is a widely used material extrusion (MEX)-based AM technique that melts thermoplastic filaments and selectively deposits them over a build platform. Despite its simplicity and affordability, it suffers from various printing defects, with partial warping being a prevalent issue. Warpage is a physical deformation caused by thermal strain incompatibility that results in the bending of the printed part away from the build platform. This study aims to investigate the warpage characteristics of printed parts based on geometrical parameters and build orientations to reduce the warpage extent.

Cuboidal samples of thermoplastic acrylonitrile butadiene styrene ranging from 5 to 80 mm were printed using a commercial MEX system. A Taguchi method-based design of experiment trial was performed to optimize the placement and orientation of the part for minimal warpage.

It was found that a lower value of the “in-plane” aspect ratio and a more prominent part thickness are favorable for minimal warpage. The part should always be placed near the region with the highest temperature (least thermal gradient) to minimize the warpage.

A novel dimensionless parameter (Y) is proposed that should be set to a minimum value to achieve minimal warpage. The results of this study can help improve the design and part placement for the MEX technique, thus elevating the print quality.

This study aims to improve the acceleration in the additive manufacturing (AM) process. AM tools, such as extrusion heads, jets, electric arcs, lasers and electron beams (EB), experience negligible forces. However, their speeds are limited by the positioning systems. In addition, a thin tool must travel several kilometers in tiny motions with several turns while realizing the AM part. Hence, acceleration is a more significant limiting factor than the velocity or precision for all except EB.

The sawtooth (ST) scanning strategy presented in this paper minimizes the time by combining three motion features: zigzag scan, 45º or 135º rotation for successive layers in G00 to avoid the CNC interpolation, and modifying these movements along 45º or 135º into sawtooth to halve the turns.

Sawtooth effectiveness is tested using an in-house developed Sand AM (SaAM) apparatus based on the laser–powder bed fusion AM technique. For a simple rectangle layer, the sawtooth achieved a path length reduction of 0.19%–1.49% and reduced the overall time by 3.508–4.889 times, proving that sawtooth uses increased acceleration more effectively than the other three scans. The complex layer study reduced calculated time by 69.80%–139.96% and manufacturing time by 47.35%–86.85%. Sawtooth samples also exhibited less dimensional variation (0.88%) than zigzag 45° (12.94%) along the build direction.

Sawtooth is limited to flying optics AM process.

Development of scanning strategy for flying optics AM process to reduce the warpage by improving the acceleration.

Electron beam-based additive manufacturing (EBAM) is an emerging technology to produce metal parts layer-by-layer. The purpose of this paper is to systematically address the research and development carried out for this technology, up till now.

This paper identifies several aspects of research and development in EBAM.

Electron beam has several unique advantages such as high scanning speed, energy efficiency, versatility for several materials and better part integrity because of a vacuum working environment.

This paper provides information on different aspects of EBAM with the current status and future scope.

Integrating additive manufacturing (AM) tools in traditional mold-making provides complex yet affordable sand molds and cores. AM processes such as selective laser sintering (SLS) and Binder jetting three-dimensional printing (BJ3DP) are widely used for patternless sand mold and core production. This study aims to perform an in-depth literature review to understand the current status, determine research gaps and propose future research directions. In addition, obtain valuable insights into authors, organizations, countries, keywords, documents, sources and cited references, sources and authors.

This study followed the systematic literature review (SLR) to gather relevant rapid sand casting (RSC) documents via Scopus, Web of Science and EBSCO databases. Furthermore, bibliometrics was performed via the Visualization of Similarities (VOSviewer) software.

An evaluation of 116 documents focused primarily on commercial AM setups and process optimization of the SLS. Process optimization studies the effects of AM processes, their input parameters, scanning approaches, sand types and the integration of computer-aided design in AM on the properties of sample. The authors performed detailed bibliometrics of 80 out of 120 documents via VOSviewer software.

This review focuses primarily on the SLS AM process.

A SLR and bibliometrics using VOSviewer software for patternless sand mold and core production via the AM process.

This paper aims to develop build strategies for rapid manufacturing of components of varying complexity with the help of illustration.

The build strategies are developed using a hybrid layered manufacturing (HLM) setup. HLM, an automatic layered manufacturing process for metallic objects, combines the best features of two well-known and economical processes, viz., arc weld-deposition and milling. Depending on the geometric complexity of the object, the deposition and/or finish machining may involve fixed (3-axis) or variable axis (5-axis) kinematics.

Fixed axis (3-axis) kinematics is sufficient to produce components free of undercuts and overhanging features. Manufacture of components with undercuts can be categorized into three methods, viz., those that exploit the inherent overhanging ability, those that involve blinding of the undercuts in the material deposition stage and those that involve variable axis kinematics for aligning the overhang with the deposition direction.

Although developed using the HLM setup, these generic concepts can be used in a variety of metal deposition processes.

This paper describes the methodology for realizing undercut features of varying complexity and also chalks out the procedure for their manufacture with the help of case studies for each approach.

The purpose of this paper is to review additive and/or subtractive manufacturing methods for metallic objects and their gradual evolution from prototyping tools to rapid manufacture of actual parts.

Various existing rapid manufacturing (RM) methods have been classified into six groups, namely, CNC machining laminated manufacturing, powder‐bed technologies, deposition technologies, hybrid technologies and rapid casting technologies and discussed in detail. The RM methods have been further classified, based on criteria such as material, raw material form, energy source, etc. The process capabilities springing from these classifications are captured in the form of a table, which acts as a database.

Due to the approximation in RM in exchange for total automation, a variety of multi‐faceted and hybrid approaches has to be adopted. This study helps in choosing the appropriate RM process among these myriad technologies.

This review facilitates identification of appropriate RM process for a given situation and sets the framework for design for RM.

To remanufacture a disused part, a hybrid process needs to be taken in part production. Therefore, a reasonable machining route is necessary to be developed for the hybrid process. This paper aims to develop a novel process planning algorithm for additive and subtractive manufacturing (ASM) system to achieve this purpose.

First, a skeleton of the model is generated by using thinning algorithm. Then, the skeleton tree is constructed based on topological structure and shape feature. Further, a feature matching algorithm is developed for recognizing the different features between the initial model and the final model based on the skeleton tree. Finally, a reasonable hybrid machining route of the ASM system is generated in consideration of the machining method of each different sub-feature.

This paper proposes a hybrid process planning algorithm for the ASM system. Further, it generates new process planning insights on the hybrid process service provider market.

The proposed process planning algorithm enables engineers to obtain a proper hybrid machining route before product fabrication. And thereby, it extends the machining capability of the hybrid process to manufacture some parts accurately and efficiently.

This study addresses one gap in the hybrid process literature. It develops the first hybrid process planning strategy for remanufacturing of disused parts based on skeleton tree matching, which generates a more proper hybrid machining route than the currently available hybrid strategy studies. Also, this study provides technical support for the ASM system to repair damaged parts.