Search results

This study aims to develop a new simple and sensitive method for the microextraction of trace levels of lead in environmental samples. It is based on the use of ionic liquids based dispersive liquid–liquid microextraction (IL–DLLME) before spectrofluorometry.

Cadmium sulphide quantum dots have been synthesised using thioglycolic acid as capping agent through a one-step process with stability and excellent water-solubility, and have strong affinity for lead (Pb). This probe is based on the fluorescence quenching effect of functionalised cadmium sulphide quantum dots.

Factors affecting the extraction efficiency and fluorescence quenching of metals, such as the amount of ionic liquid, amount of metanol, microextraction and centrifugation time, volume of quantum dots and buffer pH, were investigated. Under optimum conditions, the calibration graph was linear in the range of 0.01-3 µg.L-1, with the detection limit of 0.004 µg.L-1 for Pb2+. The relative standard deviation (RSD%, n = 5) of 5.4 per cent at 1 µg.L-1 of Pb2+ was obtained.

This method for pre-concentration of the Pb ions by dispersive liquid–liquid microextraction is novel and could be used for various applications in the synthesis of a wide variety of determination of fluorescence quenching of cadmium sulphide quantum dots.

This study aims to investigate the efficacy of Ag@GO/Na₂SiO₃ nanocomposite in eliminating As from aqueous solutions. Employing response surface methodology, the research systematically examines the adsorption process.

Various experimental parameters including sample pH, contact time, As concentration and adsorbent dosage are optimized to enhance the As removal process.

Under optimized conditions, the initial As concentration, contact time, pH and adsorbent dosage are determined to be 32 ppm, 50 mins, 6.5 and 0.4 grams, respectively. While the projected removal of As stands at 97.6% under these conditions, practical application achieves a 93% removal rate. Pareto analysis identifies the order of significance among factors as follows: adsorbent dosage > contact time > pH > As concentration.

This study highlights the potential Ag@GO/Na₂SiO₃ as a promising adsorbent for efficiently removing industrial As from aqueous solutions, and it is likely to have a good sufficiency in the filtration of water and wastewater treatment plans to remove some chemical pollution, including paints and heavy metals.

The simplicity of the nanocomposite preparation method without the need for advanced equipment and the cheapness of the raw materials and its potential ability to remove As are the prominent advantages of this research.

This study’s aim is to introduce a high-performance sorbent for the removal of both anionic (Congo red; CR) and cationic (methylene blue; MB) dyes from aqueous solutions.

Sodium silicate is adopted as a substrate for GO and AgNPs with positive charge are used as modifiers. The synthesized nanocomposite is characterized by FTIR, FESEM, EDS, BET and XRD techniques. Then, some of the most effective parameters on the removal of CR and MB dyes such as solution pH, sorbent dose, adsorption equilibrium time, primary dye concentration and salt effect are optimized using the spectrophotometry technique.

The authors successfully achieved notable maximum adsorption capacities (Qmax) of CR and MB, which were 41.15 and 37.04 mg g⁻¹, respectively. The required equilibrium times for maximum efficiency of the developed sorbent were 10 and 15 min for CR and MB dyes, respectively. Adsorption equilibrium data present a good correlation with Langmuir isotherm, with a correlation coefficient of R2 = 0.9924 for CR and R2 = 0.9904 for MB, and kinetic studies prove that the dye adsorption process follows pseudo second-order models (CR R2 = 0.9986 and MB R2 = 0.9967).

The results showed that the proposed mechanism for the function of the developed sorbent in dye adsorption was based on physical and multilayer adsorption for both dyes onto the active sites of non-homogeneous sorbent.

The as-prepared nano-adsorbent has a high ability to remove both cationic and anionic dyes; moreover, to the high efficiency of the adsorbent, it has been tried to make its synthesis steps as simple as possible using inexpensive and available materials.