Search results

The paper focuses on design, fabrication and characterization of electromagnetic microgenerators with integrated rectifying circuits to convert AC output signal to DC one. The work includes research on simulation of voltage-rectifying circuits, including charge pump, realization of the experimental printed circuit board (PCB) with selected electronic circuits and the execution of the final structure with integrated rectifying circuit. Measurements were performed on these circuits.

Electromagnetic microgenerators include multipole permanent magnets secured on rotor three-phase brushless direct current (BLDC) motor and planar multilayer multiple coils. These were fabricated using low temperature co-fired ceramics (LTCC) technology. In our experiment, six rectifying circuits were simulated and tested with a structure consisting of eight layers of coils and with an outer diameter of 50 mm fabricated earlier.

The microgenerator with Graetz bridge generates higher output power than the modified charge pump at the same rotary speed. However, it is less stable for the distance change between the structure and the magnets than the modified charge pump, which has more constant output power in a wider range of load resistance.

The presented electronic rectifying circuits are novel for LTCC-based electromagnetic microgenerator application. The structure with integrated rectifying circuits allows generation of electrical output power larger than 100 mW at the rotor speed of about 8,000 rpm.

The purpose of this paper is to characterize electrical properties of nickel-phosphorus (Ni-P) thin-film resistors made on FR-4 laminate in a wide range of temperature (from −180 to 20°C).

The study was performed using resistors made of Ni-P foil with two different thicknesses (0.1 or 0.05 μm) and sheet resistances (100 or 250 Ω/sq), respectively. The resistance rectangular resistors had length and width from the range between 0.59 and 5.91 mm. The resistance versus temperature characteristics and their distribution as well as resistors ' durability to low-temperature thermal shocks were investigated.

The results showed almost linear temperature dependence of resistance with a negative temperature coefficient of resistance of about −95 ppm/°C for 250 Ω/sq layer and −55 ppm/°C for 100 Ω/sq layer. A very small dimensional effect was observed for sheet resistance as well as for R(T) characteristic. Thin-film resistors are also characterized by very high durability to low-temperature thermal shocks.

The results presented in this paper can be very useful for low-temperature applications of thin-film resistors made on printed circuit boards. They suggest possibility of wide applications of these components in a wide temperature range.

This paper aims to focus on the application of low temperature co-fired ceramic (LTCC) technology in the fabrication of a microfluidic module with integrated microwave components. The design, technology and performance of such an LTCC-based module is investigated. The rapid heating of liquid samples on a microliter scale is shown to be possible with the use of microwaves.

The developed microwave-microfluidic module was fabricated using well-known LTCC technology. The finite element method was used to design the geometry of the microwave circuit. Various numerical simulations for different liquids were performed. Finally, the performance of the real LTCC-based microwave-microfluidic module was examined experimentally.

LTCC materials and technology can be used in the fabrication of microfluidic modules which use microwaves in the heating of the liquid sample. LTCC technology permits the fabrication of matching circuits with appropriate geometry, whereas microwave power can be used to heat up the liquid samples on a microliter scale.

The main limitation of the presented work is found to be in conjunction with LTCC technology. The dimensions and shape of the deposited conductors (e.g. microstrip line, matching circuit) depend on the screen-printing process. A line with resolution lower than 75 µm with well-defined edges is difficult to obtain. This can have an effect on the high-frequency properties of the LTCC modules.

The presented LTCC-based microfluidic module with integrated microwave circuits provides an opportunity for the further development of various micro-total analysis systems or lab-on-chips in which the rapid heating of liquid samples in low volumes is needed (e.g. miniature real-time polymerase chain reaction thermocycler).

Examples of the application of LTCC technology in the fabrication of microwave circuits and microfluidic systems can be found in the available literature. However, the LTCC-based module which combines microwave and microfluidic components has yet to have been reported. The preliminary work on the design, fabrication and properties of the LTCC microfluidic module with integrated microwave components is presented in this paper.

Crystallization is the process widely used for components separation and solids purification. The systems for crystallization process evaluation applied so far, involve numerous non-invasive tomographic measurement techniques which suffers from some reported problems. The purpose of this paper is to show the abilities of three-dimensional Electrical Capacitance Tomography (3D ECT) in the context of non-invasive and non-intrusive visualization of crystallization processes. Multiple aspects and problems of ECT imaging, as well as the computer model design to work with the high relative permittivity liquids, have been pointed out.

To design the most efficient (from a mechanical and electrical point of view) 3D ECT sensor structure, the high-precise impedance meter was applied. The three types of sensor were designed, built, and tested. To meet the new concept requirements, the dedicated ECT device has been constructed.

It has been shown that the ECT technique can be applied to the diagnosis of crystallization. The crystals distribution can be identified using this technique. The achieved measurement resolution allows detecting the localization of crystals. The usage of stabilized electrodes improves the sensitivity of the sensor and provides the images better suitable for further analysis.

The dedicated 3D ECT sensor construction has been proposed to increase its sensitivity in the border area, where the crystals grow. Regarding this feature, some new algorithms for the potential field distribution and the sensitivity matrix calculation have been developed. The adaptation of the iterative 3D image reconstruction process has also been described.