Radha Sankararajan, Kirubaveni Savarimuthu, Sudha Murugesan, Kiruthika Ramany, Govindaraj Rajamanickam and Santhosh Narendhiran
The purpose of this paper is to fabricate an ethanol sensor which has bio-friendly and eco-friendly properties compared to the commercially available ethanol sensors.
Abstract
Purpose
The purpose of this paper is to fabricate an ethanol sensor which has bio-friendly and eco-friendly properties compared to the commercially available ethanol sensors.
Design/methodology/approach
This paper describes the construction of a highly sensitive ethanol sensor with low ppm level detection at room temperature by integrating three techniques. The first deals with the formation of organic/inorganic p-n heterojunction. Second, tuning of structural parameters such as length, diameter and density of Zinc Oxide (ZnO) nanostructure was achieved through introduction of the Fe dopant into a pure ZnO seed layer. Furthermore, ultra-violet (UV) light photoactivation approach was used for enhancing the sensing performance of the fabricated sensors. Four different sensors were fabricated by combing the above approaches. The structural, morphological, optical and material compositions were characterized using different characterization techniques. Sensing behavior of the fabricated sensors toward ethanol was experimented at room temperature with and without UV illumination combined with stability studies. It was observed that all the fabricated sensors showed enhanced sensing performance for 10 ppm of ethanol. In specific, FNZ (Fe-doped ZnO seeded Ni-doped Zn nanorods) sensor exhibited a higher response at 2.2 and 13.5 s for 5 ppm and 100 ppm of ethanol with UV light illumination at room temperature, respectively. The photoactivated FNZ sensor showed quick response and speedy recovery at 18 and 30 s, respectively, for 100 ppm ethanol.
Findings
In this study, the authors have experimentally analyzed the effect of Fe (in ZnO seed layer and ZnO NRs) and Ni (in ZnO NRs) dopants in the room temperature sensing performance (with and without UV light) of the fabricated ethanol sensors. Important sensing parameters like sensitivity, recovery and response time of all the fabricated sensors are reported.
Originality/value
The Fe doped ZnO seeded Ni doped Zn nanorods (FNZ sample) showed a higher response at 2.2 s and 13.5 s for very low 5 ppm and 10 ppm of ethanol at room temperature under UV light illumination when compared to the other fabricated sensors in this paper. Similarly, this sensor also had quick response (18 s) and speedy recovery (30 s) for 100 ppm ethanol.
Details
Keywords
Iyappan Gunasekaran, Govindaraj Rajamanickam, Santhosh Narendiran, Ramasamy Perumalsamy, Kiruthika Ramany and Radha Sankararajan
Various approaches have been made to alter the vibration sensing properties of zinc oxide (ZnO) films to achieve high sensitivity. This paper aims to report the experimental study…
Abstract
Purpose
Various approaches have been made to alter the vibration sensing properties of zinc oxide (ZnO) films to achieve high sensitivity. This paper aims to report the experimental study of the fabrication of precursor molar ratio concentration varied ZnO nanostructures grown on rigid substrates using the refresh hydrothermal method. The effect of these fabricated ZnO nanostructures-based vibration sensors was experimentally investigated using a vibration sensing setup.
Design/methodology/approach
ZnO nanostructures have been grown using low temperature assisted refresh hydrothermal method with different precursor molar concentrations 0.025 M (R1), 0.075 M (R2) and 0.125 M (R3). Poly 3,4-ethylenedioxythiophene polystyrene sulfonate, a p-type material is spun coated on the grown ZnO nanostructures. Structural analysis reveals the increased intensity of the (002) plane and better c-axis orientation of the R2 and R3 sample comparatively. Morphological examination shows the changes in the grown nanostructures upon increasing the precursor molar concentration. The optical band gap value decreases from 3.11 eV to 3.08 eV as the precursor molar concentration is increased. Photoconductivity study confirms the formation of a p-n junction with less turn-on voltage for all the fabricated devices. A less internal resistance of 0.37 kΩ was obtained from Nyquist analysis for R2 compared with the other two fabricated samples. Vibration testing experimentation showed an improved output voltage of the R2 sample (2.61 V at 9 Hz resonant frequency and 2.90 V for 1 g acceleration) comparatively. This also gave an increased sensitivity of 4.68 V/g confirming its better performance when compared to the other fabricated two samples.
Findings
Photoconductivity study confirms the formation of a p-n junction with less turn-on voltage for all the fabricated devices. A less internal resistance of 0.37 kΩ was calculated from the Nyquist plot. Vibration testing experimentation proves an increased sensitivity of 4.68 V/g confirming its better performance when compared to the other fabricated two samples.
Originality/value
Vibration testing experimentation proves an increased sensitivity of 4.68 V/g for R2 confirming its better performance when compared to the other fabricated two samples.