Search results

Small companies have limited management and financial resources and, although better quality assurance will in the longer term reduce manufacturing costs, many are intimidated by the set up and running costs of certification under an approved scheme such as BS 5750. The article describes the first year's operation of a pilot scheme intended to help small companies resolve these problems. Experienced quality managers, recruited by an academic institution and with the institution's backing, have acted as managers for a group of small companies on a shared cost basis. The experience gained from this scheme is discussed.

The costs, benefits and implications of BS5750/ISO9000 certification for small and medium‐sized firms are investigated on the basis of a review of published literature and a survey of the actual experience of a representative sample of firms. The principle motivation for installing BS5750‐based quality systems appears to be customer pressure; retaining existing customers is a key benefit. A minority of firms discover that “internal” benefits, such as greater control and discipline, turn out to be more valuable. Developing and installing a BS5750‐based system is a major exercise for small firms but through reductions in quality costs, the costs of certification can typically be recovered within three years of commencing to operate the system. The attitude of the chief executive is a key determinant of effectiveness.

At present, manufacturing firms in the Kingdom of Saudi Arabia (KSA) are considering the adoption of quality control (QC) techniques. Conducts a survey to investigate the awareness of quality and to shed some light on the extent of the practice and content of the QC process in manufacturing firms in KSA.

This monograph presents some findings, based on four pieces of work funded by the Department of Trade and Industry, on the influence of the National Quality Campaign on UK industry. Amongst the main conclusions are that the campaign material has been relatively successful in reaching its prime target of senior management, the majority of respondents have found the material to be useful and believe that the campaign has benefited their organisation in terms of increased awareness of the importance of total quality management and that few chief executives are actively involved in the process of quality improvement. It is also pointed out that respondents have been selective in their choice of material and chief executives were more discriminating than their subordinates. The selection of material appears to be dependent upon brochure content, respondents′ position in the organisational hierarchy and respondents′ perception of the relevance of material. There is little doubt that people have high expectations of Government in continuing to promote national awareness of quality management and disseminating quality‐related information. The monograph goes on to explore possible future initiatives along the lines of a Pan‐European dimension.

The next month or two behind us and this decade will have passed, to merge in the drab background of the post‐war years, part of the pattern of frustration, failure and fear. The ‘swinging sixties’ some called it, but to an older and perhaps slightly jaundiced eye, the only swinging seemed to be from one crisis to another, like the monkey swinging from bough to bough in his home among the trees; the ‘swingers’ among men also have their heads in the clouds! In the seemingly endless struggle against inflation since the end of the War, it would be futile to fail to see that the country is in retreat all the time. One can almost hear that shaft of MacLeodian wit christening the approaching decade as the ‘sinking seventies’, but it may not be as bad as all that, and certainly not if the innate good sense and political soundness of the British gives them insight into their perilous plight.

This present aims to present the numerical study of the unsteady stretching/shrinking flow of a fluid-particle suspension in the presence of the constant suction and dust particle slip on the surface.

The governing partial differential equations for the two phases flows of the fluid and the dust particles are reduced to the pertinent ordinary differential equations using a similarity transformation. The numerical results are obtained using the bvp4c function in the Matlab software.

The results revealed that in the decelerating shrinking flow, the wall skin friction is higher in the dusty fluid when compared to the clean fluid. In addition, the effect of the fluid-particle interaction parameter to the fluid-phase can be seen more clearly in the shrinking flow. Other non-dimensional physical parameters such as the unsteadiness parameter, the mass suction parameter, the viscosity ratio parameter, the particle slip parameter and the particle loading parameter are also considered and presented in figures. Further, the second solution is discovered in this problem and the solution expanded with higher unsteadiness and suction values. Hence, the stability analysis is performed, and it is confirmed that the second solution is unstable.

In practice, the flow conditions are commonly varying with time; thus, the study of the unsteady flow is very crucial and useful. The problem of unsteady flow of a dusty fluid has a wide range of possible applications such as in the centrifugal separation of particles, sedimentation and underground disposable of radioactive waste materials.

Even though the problem of dusty fluid has been broadly investigated, limited discoveries can be found over an unsteady shrinking flow. Indeed, this paper managed to obtain the second (dual) solutions, and stability analysis is performed. Furthermore, the authors also considered the artificial particle-phase viscosity, which is an important term to study the particle-particle and particle-wall interactions. With the addition of this term, the effects of the particle slip and suction parameters can be investigated. Very few studies in the dusty fluid embedded this parameter in their problems.

This paper aims to examine the Cu-Al2O3/water hybrid nanofluid flow over a shrinking sheet in the presence of the magnetic field and dust particles.

The governing partial differential equations for the two-phase flow of the hybrid nanofluid and the dust particles are reduced to ordinary differential equations using a similarity transformation. Then, these equations are solved using bvp4c in MATLAB software. The bvp4c solver is a finite-difference code that implements the three-stage Lobatto IIIa formula. The numerical results are gained for several values of the physical parameters. The effects of these parameters on the flow and the thermal characteristics of the hybrid nanofluid and the dust particles are analyzed and discussed. Later, the temporal stability analysis is used to determine the stability of the dual solutions obtained as time evolves.

The outcome shows that the flow is unlikely to exist unless satisfactory suction strength is imposed on the shrinking sheet. Besides, the heat transfer rate on the shrinking sheet decreases with the increase of . However, the increase in and lead to enhance the heat transfer rate. Two solutions are found, where the domain of the solutions is expanded with the rising of, and. Consequently, the boundary layer separation on the surface is delayed in the presence of these parameters. Implementing the temporal stability analysis, it is found that only one of the solutions is stable as time evolves.

The dusty fluid problem has been widely studied for the flow over a stretching sheet, but only limited findings can be found for the shrinking counterpart. Therefore, this study considers the problem of the dusty fluid flow over a shrinking sheet containing Cu-Al₂O₃/water hybrid nanofluid with the effect of the magnetic field. In fact, this is the first study to discover the dual solutions of the dusty hybrid nanofluid flow over a shrinking sheet. Also, further analysis shows that only one of the solutions is stable as time evolves.

To explore the fusion of dust particles and of polymers in a viscous liquid is the main purpose of this article. Newtonian fluid as a base fluid is considered and the mutual presence of polymers and dusty bodies is investigated. It discusses the steady laminar flow and heat transportation of a polymeric dusty liquid induced by a uniformly heated, penetrable and stretchable surface inside the boundary layer.

The mathematical system incorporates separate equations of energy and momentum for dusty bodies and for fluid. The classical Oldroyd-B model is chosen for exploring polymer presence. For the fluid phase, this model adds another stress to the conservation law of momentum. Appropriate similarity variables are introduced to transform the system of partial differential equations (PDEs) into a system of nonlinear ordinary differential equations (ODEs). The problem is solved by introducing a numerical iterative procedure which turned out to be fastly converging.

Expeditious changes inside the boundary layer cause polymers to deform. No changes outside the boundary layer are noticed on account of polymer stretching. The dependence of heat transfer rate and skin friction on the parameter of polymer concentration and Weissenberg number is analyzed and displayed graphically against interaction parameters for temperature and velocity, dust particles’ mass concentration, Eckert and Prandtl numbers. Combining effects of polymers and dust particles cause skin friction to decrease and heat transfer rate to increase. Increasing values of interaction parameter for velocity, dust particles’ mass concentration and Eckert number reduces the drag coefficient and local Nusselt number. On the other hand, the Prandtl number and interaction parameter of temperature magnify the heat flux at the wall.

This article studies the infinite extensibility of polymers. FENE and FENE-P models can be used to investigate the polymer presence in dusty fluids in the future.

In this article, the authors’ aim is to study the combined presence of polymers and dusty bodies. Keeping the existing literature in view, this type of fusion is not studied yet. Polymer inclusion in a viscous dusty fluid is studied and the behavior of fluid flow and heat transportation is investigated within the boundary layer over a permeable linearly stretching sheet.

Knight's Industrial Law Reports goes into a new style and format as Managerial Law This issue of KILR is restyled Managerial Law and it now appears on a continuous updating basis rather than as a monthly routine affair.

The purpose of this paper is to numerically study the boundary layer problem for the case of two-dimensional flow of dusty fluid over a shrinking surface in the presence of the fluid suction at the surface.

The governing equations of the problem are reduced to the system of ordinary differential equations using the similarity transformation and then solved using the bvp4c method in the Matlab software.

The effects of the drag coefficient parameter L, the fluid–particle interaction parameter δ, the suction parameter s and the particle loading parameter ω on the flow of the permeable shrinking sheet are investigated. It is found that the aforementioned parameters have different effects in the shrinking sheet flow. This study has also succeeded in discovering the second solution, and through the stability analysis, it is suggested that the solution is unstable and not physically realizable in practice.

The current findings add to a growing body of literature on the boundary layer problem in the dusty fluid. The dusty fluid is significant in various practical applications such as in the transporting suspended powdered materials through pipes, propulsion and combustion in rockets, the flow of blood in arteries, wastewater treatment and as corrosive particles in engine oil flow.

Even though the dusty fluid problem has been extensively studied in the flow of the stretching sheet, limited findings can be found over a shrinking flow. In fact, this is the first study to discover the second solution in the dusty fluid problem.