Search results

The purpose of this paper is to present the result of calculations that were performed to estimate the structural weight of the passenger aircraft using novel technological solution. Mass penalty resulting from the installation of the fuselage boundary layer ingestion device was needed in the CENTRELINE project to be able to estimate the real benefits of the applied technology.

This paper focusses on the finite element analysis (FEA) of the fuselage and wing primary load-carrying structures. Masses obtained in these analyses were used as an input for the total structural mass calculation based on semi-empirical equations.

Combining FEA with semi-empirical equations makes it possible to estimate the mass of structures at an early technology readiness level and gives the possibility of obtaining more accurate results than those obtained using only empirical formulas. The applied methodology allows estimating the mass in case of using unusual structural solutions, which are not covered by formulas available in the literature.

Accurate structural mass estimation is possible at an earlier design stage of the project based on the presented methodology, which allows for easier and less costly changes in designed aircrafts.

The presented methodology is an original method of mass estimation based on a two-track approach. The analytical formulas available in the literature have worked well for aeroplanes of conventional design, but thanks to the connection with FEA presented in this paper, it is possible to estimate the structure mass of aeroplanes using unconventional technological solutions.

The aim of this study was to first establish foundational algebraic expressions that parametrically describe any advanced dual-energy storage–propulsion–power system (DESPPS) and then proceed to declare the array of fundamental independent variables necessary for the sizing and optimisation of such systems. Upon procurement of a pre-design-level integrated aircraft performance model and the subsequent verification against previously published high-end low-fidelity generated results, opportunity was taken in formulating a set of battery-based DESPPS related design axioms and sizing heuristics.

Derivation of algebraic expressions related to describing DESPPS architectures are based on first principles. Integrated performance modelling by way of full analytical fractional change transformations anchored according to a previously published Energy Specific Air Range (ESAR) figure-of-merit originally derived using the Breguet–Coffin differential equation for vehicular efficiency. Weights prediction of sub-systems that constitute the entire aircraft including DESPPS constituents emphasises an analytical foundation with minimal implementation of linear correlation factors or coefficients of proportionality. An iterative maximum take-off weight build-up algorithm emphasising expedient and stable convergence was fashioned. All prediction methods pertaining to integrated performance were verified according to previously published battery-based DESPPS results utilising high-end low-fidelity methods.

For all types of DESPPS, two new fundamental independent non-dimensional variables were declared: the Supplied Power Ratio (related to converted power afforded by each energy carrier); and, the Activation Ratio (describing the relative nature of utilisation with respect to time afforded by the motive power device associated with each energy source). For a given set of standalone sub-system energy conversion efficiencies, the parametric descriptor of degree-of-hybridisation (DoH) for Power was found to be solely a function of the Supplied Power Ratio, whereas in contrast, the DoH for Energy was found to be a more complex synthetic function described by comingling of Supplied Power Ratio and the Activation Ratio. Upon examination of the integrated aircraft performance model derived in this treatise, for purposes of investigating CO₂-emissions reduction potential for battery-based DESPPS using kerosene as one of the energy sources, one salient observation was maximising the ESAR figure-of-merit is not an appropriate objective or intermediary function for future optimisation work. It was found maximising block fuel reduction through the use of maximum ESAR would lead to ever diminishing design ranges and curtailment of the payload-range working capacity of the aircraft.

Opportunity is now given to design and optimise aircraft utilising any type of DESPPS architecture. It was established that designing for battery-based DESPPS aircraft can be achieved effectively in a two-stage process that may not require aircraft morphologies more exotic than the so-called “wing-and-tube”. Firstly, a suitably projected state-of-the-art aircraft with solely advanced gas-turbine technology for the propulsion and power system needs to be produced. Thereafter, a revised version of this baseline projected aircraft now using DESPPS architecture should be conceived. A recommendation related to CO₂-emissions reduction potential for battery-based DESPPS using kerosene as one of the energy sources is that during optimisation work the multi-objective formulation should comprise at least two functions: block fuel and operating economics. In all instances, it was advised that the objective function of block fuel should be tempered by an equality constraint of ESAR parity with the baseline projected aircraft using gas-turbine only technology.

A complete, unified analytical description of DESPPS that is universally applicable to any type of energy carrier has been derived and verified for battery-based dual-energy systems. Correspondingly, a set of aircraft design axioms and sizing heuristics relevant to battery-based DESPPS have been presented.

A semi‐empirical relationship is derived for the structural weight of wings, applicable to a wide range of subsonic aircraft. The method is based on a generalized expression for the material required to resist the root bending moment due to wing lift in a specified flight condition. Appropriate factors make the result applicable to cantilever and braced wings, for passenger and general aviation aircraft and for freighters. An assessment of the accuracy, based on actual wing weights of 46 aircraft, indicates that a standard deviation of 9·64 per cent is achieved. The weight formula presented allows for the effects of variations in the main wing dimensions and operational limits of the airplane and is therefore suited to parametric design studies.

A conceptual design method for composite material stiffened panels used in aircraft tail structures and unmanned aircraft has been developed to bear compression and shear loads.

The method is based on classical laminated theory to fulfil the requirement of building a fast design tool, necessary for this preliminary stage. The design criterion is local and global buckling happen at the same time. In addition, it is considered that the panel does not fail due to crippling, stiffeners column buckling or other manufacturing restrictions. The final geometry is determined by minimising the area and, consequently, the weight of the panel.

The results obtained are compared with a classical method for sizing stiffened panels in aluminium. The weight prediction is validated by weight reductions in aircraft structures when comparing composite and aluminium alloys.

The work is framed in conceptual design field, so hypotheses like material or stiffeners geometry shall be taken a priori. These hypotheses can be modified if it is necessary, but even so, the methodology continues being applicable.

The procedure presented in this paper allows designers to know composite structure weight of aircraft tails in commercial aviation or any lifting surface in unmanned aircraft field, even for unconventional configurations, in early stages of the design, which is an aid for them.

The contribution of this paper is the development of a new rapid methodology for conceptual design of composite panels and the feasible application to aircraft tails and also to unmanned aircraft.

A COMPILATION of formulae and data from the article on the same subject in the July 1971 issue of AIRCRAFT ENGINEERING is presented to enable weight engineers to make a quick estimation of wing structural weight for preliminary aircraft design. Application of the method to 46 samples of aircraft in a wide range of sizes demonstrates a standard deviation of 9·64 per cent, satisfactory for point designs and parametric studies.

The purpose of this study of which this work is only the first part, is the development of conceptual design tools to perform an optimized design of the rear fuselage and tail surfaces. The development of a new and extensive database of transport aircraft and an analysis of certain general, rear fuselage and horizontal stabilizer parameters of the aircraft are presented in this paper.

In addition to the development of a comprehensive high accurate database, linear and non-linear correlations between different parameters of the aircraft have been established. Data were analyzed using comparison criteria between aircraft database based on the mission, the number of engines installed or arrangement of the tail surfaces.

It has been possible to obtain very relevant, linear and non-linear correlations for critical design parameters to optimize the design of the rear fuselage and horizontal tail.

In the case of the tail cone, the data have not yielded significant correlations. On the other hand, there are some regressions that do not work well in some cases and for which it would be good to further expand the database.

Results obtained greatly improve the existing methods for conceptual design, which usually pay no attention to the rear part of the aircraft. Besides, these new procedures are adapted to different categories of aircraft, allowing greater optimization of the designs.

The novel contribution of this work is focused on the development of a new high-fidelity database and includes many more aircraft than any other work previously released. Also, new correlations, linear and non-linear, additional parameters not considered in previous studies, and differentiated by category of aircraft studies are provided.

The present work aims to analyze the feasibility of wingtip device incorporation into transport airplane configurations considering many aspects such as performance, cost and environmental impact. A design framework encompassing optimization for wing-body configurations with and without winglets is described and application examples are presented and discussed.

modeFrontier, an object-oriented optimization design framework, was used to perform optimization tasks of configurations with wingtip devices. A full potential code with viscous effects correction was used to calculate the aerodynamic characteristics of the fuselage–wing–winglet configuration. MATLAB® was also used to perform some computations and was easily integrated into the modeFrontier frameworks. CFD analyses of transport airplanes configurations were also performed with Fluent and CFD++ codes.

Winglet provides considerable aerodynamic benefits regarding similar wings without winglets. Drag coefficient reduction in the order of 15 drag counts was achieved in the cruise condition. Winglet also provides a small boost in the clean-wing maximum lift coefficient. In addition, less fuel burn means fewer emissions and contributes toward preserving the environment.

More efficient transport airplanes, presenting considerable lower fuel burn.

Among other contributions, wingtip devices reduce fuel burn, engine emissions and contribute to a longer engine lifespan, reducing direct operating costs. This way, they are in tune with a greener world.

The paper provides valuable wind-tunnel data of several winglet configurations, an impact of the incorporation of winglets on airplane design diagram and a direct comparison of two optimizations, one performed with winglets in the configuration and the other without winglets. These simulations showed that their Pareto fronts are clearly apart from each other, with the one from the configuration with winglets placed well above the other without winglets. The present simulations indicate that there are always aerodynamic benefits present regardless the skeptical statements of some engineers. that a well-designed wing does not need any winglet.

When comparing and contrasting different types of fixed-wing military aircraft on the basis of an energetic efficiency figure-of-merit, unmanned aerial vehicles (UAVs) dedicated to tactical medium-altitude long-endurance (MALE) operations appear to have significant potential when hybrid-electric propulsion and power systems (HEPPS) are implemented. Beginning with a baseline Eulair drone, this paper aims to examine the feasibility of retro-fitting with an Autarkic-Parallel-HEPPS architecture to enhance performance of the original single diesel engine.

In view of the low gravimetric specific energy performance attributes of batteries in the foreseeable future, the best approach was found to be one in which the Parallel-HEPPS architecture has the thermal engine augmented by an organic rankine cycle (ORC). For this study, with the outer mould lines fixed, the goal was to increase endurance without increasing the Eulair drone maximum take-off weight beyond an upper limit of +10%. The intent was to also retain take-off distance and climb performance or, where possible, improve upon these aspects. Therefore, as the focus of the work was on power scheduling, two primary control variables were identified as degree-of-hybridisation for useful power and cut-off altitude during the en route climb phase. Quasi-static methods were used for technical sub-space modelling, and these modules were linked into a constrained optimisation algorithm.

Results showed that an Autarkic-Parallel-HEPPS architecture comprising an ORC thermal energy recovery apparatus and high-end year-2020 battery, the endurance of the considered aircraft could be increased by 11%, i.e. a total of around 28 h, including de-icing system, in-flight recharge and emergency aircraft recovery capabilities. The same aircraft with the de-icing functionality removed resulted in a 20% increase in maximum endurance to 30 h.

Although the adoption of Series/Parallel-HEPPS only solutions do tend to generate questionable improvements in UAV operational performance, combinations of HEPPS with energy recovery machines that use, for example, an ORC, were found to have merit. Furthermore, such architectural solutions could also offer opportunity to facilitate additional functions like de-icing and emergency aircraft recovery during engine failure, which is either not available for UAVs today or prove to be prohibitive in terms of operational performance attributes when implemented using a conventional PPS approach.

This technical paper highlights a new degree of freedom in terms of power scheduling during climbing transversal flight operations. A control parameter of cut-off altitude for all types of HEPPS-based aircraft should be introduced into the technical decision-making/optimisation/analysis scheme and is seen to be a fundamental aspect when conducting trade-studies with respect to degree-of-hybridisation for useful power.

The purpose of this paper is to propose a solution of the engine bypass ratio choice problem of a very light jet (VLJ) class aircraft using the multiple objective optimization (MOO) method.

The work focuses on the choice of one of the most essential parameters of the jet engine, that is its bypass ratio. The work presents the methodology of optimal designing using the multitask character of the matter which is based on the mathematical model of optimization in the concept of the set theory. To make an optimal choice of the chosen parameter, a complete computational model of an aircraftwas made (aerodynamic, power unit, performance and cost) and then the method that allows to choose the bypass ratio was selected, regardingmultiple estimating criteria of the obtained solutions. The presented method can be used at the concept design state for determining the chosen and most important technical parameters of the aircraft.

The way to design a competing aircraft is to choose its design parameters, including the power unit, by using the advanced methods of MOO. The main aim of the work was to demonstrate a method of selecting chosen parameters of the transport aircraft at the preliminary design stage. The work focuses on the choice of bypass ratio of the jet engine of the VLJ. The method could be helpful at the preliminary design stage of a new aircraft to selection of other design parameters.

The exemplary calculations were made for 50 different transport tasks to take into account different performance conditions of the aircraft. The presented method can be used at the concept design state for determining the chosen and most important technical parameters of the aircraft.

The work shows a practical possibility to implement the proposed method. The presented method could be helpful at the preliminary design stage of a new aircraft to select its design parameters. The results of the analyses are a separate point for further research and studies.

The work shows a practical possibility to implement the proposed approach for design problems at early stages of product development.

The purpose of this work is to further develop the methodology for calculating the aircraft take-off mass and its main functional components for the conceptual analysis and synthesis of new projects.

The method is based on the assessment of changes in the take-off gross mass (TOGM) of the already developed project or already existing a basic version of the aircraft when making local mass changes for its modification or for the numerical researches to create a more advanced project. The method is based on the “sensitivity factors of mass” (SFM) of aircraft, which represents the ratio of TOGM to initial (local) mass changes of its main functional components. The method of analytical refined calculation of SFM for the initial mass change and the main aerodynamic characteristics is given.

In comparison with the long-known method based on weight (mass) growth factors, which were considered constant, this method takes into account the dependence from the value of the initial local mass change and its functional purpose.

This method allows the designer to calculate more strictly the final changes in the TOGM on the initial stages of conceptual design when finding new project solutions. Numerical calculations are given on the example of passenger aircraft. The dependence of SFM and TOGM and its functional masses on the value of the initial change of the structure mass are shown. This method is used in the educational process at the college of Aerospace Engineering in the Aircraft Design department.

The considered method based on SFM is simple and convenient and more accurate for conducting project research on many project parameters when analyzing and synthesizing a new project.