Search results

The leaching of lead from electronic components in landfills to ground water is harmful to health and to the environment. Increasing concern over the use of lead in electronics manufacturing has led to legislation to restrict its use as a joining material. Consequently, significant recent research efforts have been geared to identification of suitable lead‐free solder pastes. Typically, lead‐free solder pastes contain a very active flux in an effort to improve wetting. These aggressive fluxes have the tendency to explode (or burst) and create flux spatter, causing many process problems with sensitive electronic components. The purpose of this paper is to propose solution procedures to minimize/eliminate these flux spatters, particularly, on gold fingers in memory modules when lead‐free solder pastes are used.

Four no‐clean, lead‐free Sn‐Ag‐Cu (SAC) alloy‐based solder pastes consisting of four different flux systems from three different vendors were evaluated. Two types of reflow profiles (linear and ramp‐soak‐ramp) were also evaluated. Experiments were also conducted to optimise the soak temperature and soak time to determine a broader process window for lead‐free volume production with minimal flux spatter on the contact fingers of memory modules. In order to validate our findings the recommended profile and paste was adopted in production. Additional experiments on a board with a different surface finish were also carried out to validate the recommendations.

Flux spatter can be reduced/eliminated through proper selection of flux chemistry and reflow profile optimisation. The experimental study conducted indicates there is a reduction in the occurrence of flux spatter when a ramp‐soak‐ramp profile is used with lead‐free solder pastes.

Demonstrates that flux spatter can be reduced/eliminated by carefully choosing a soak profile and appropriate flux chemistry.

The global construction industry faces both challenges and opportunities from electronic waste (e-waste). This study aims to present a bibliometric analysis and comprehensive literature assessment on e-waste in concrete construction materials.

This study studies 4,122 Scopus documents to examine garbage generation in different countries and inventive ways to integrate e-waste into construction as a sustainable strategy. This study lists famous researchers and their cooperation networks, demonstrating a robust and dynamic area with a surge in research output, notably from 2018 to 2022. Data is visually represented using VOS Viewer to show trends, patterns and study interests throughout time.

The findings imply that e-waste can improve construction materials’ mechanical characteristics and sustainability. The results are inconsistent and suggest further optimization. e-Waste into construction has garnered scientific interest for its environmental, life cycle, and economic impacts. This field has great potential for improving e-waste material use, developing sophisticated prediction models, studying environmental implications, economic analysis, policy formulation, novel construction methods, global cooperation and public awareness. This study shows that e-waste can be used in sustainable building. It stresses this area’s need for research and innovation. This lays the groundwork for using electronic trash in buildings, which promotes a circular economy and environmental sustainability.

The findings underscore the critical role of ongoing research and innovation in leveraging e-waste for sustainable building practices. This study lays the groundwork for integrating e-waste into construction, contributing to the advancement of a circular economy and environmental sustainability.

The social implications of integrating e-waste into construction are significant. Using e-waste not only addresses environmental concerns but also promotes social sustainability by creating new job opportunities in the recycling and construction sectors. It fosters community awareness and responsibility towards sustainable practices and waste management. Additionally, this approach can reduce construction costs, making building projects more accessible and potentially lowering housing prices.

This research contributes to the field by offering a bibliometric analysis and comprehensive assessment of e-waste in concrete construction materials, highlighting its global significance.

The purpose of this study is to optimize processing parameters to get the smallest average surface roughness (Ra) and delamination damage (F_d) values during drilling via abrasive water jet (AWJ) of the glass fiber-reinforced polymer composite material produced at [0°/90°]_s fiber orientation angles.

Drilling experiments were done via AWJ with three-axis computer numerical control (CNC) control system. Machine processing parameters such as water pressure of 3,600, 4,300, 4,800 and 5,300 bar; stand-off distance of 1, 2, 3 and 4 mm; traverse rate of 750, 1,500, 2,000 and 3,000 mm/min; and hole diameters of 8, 10, 12 and 14 mm have been selected. The effects of processing parameters in drilling experiments were investigated in conformity with the Taguchi L₁₆ orthogonal array and the data obtained were analyzed using Minitab 17 software. The signal/noise (S/N) ratio was taken as a basis for evaluating the test results. Optimum processing conditions were determined by calculating the S/N ratio for both Ra and F_d in conformity with the “smaller is better” approximation. The effects of processing parameters on Ra and F_d were statistically investigated using analysis of variance, S/N ratio and Taguchi-based gray relational analysis. Ra and F_d were predicted by evaluating with the ANN model and were predicted with the least amount of error.

It has been determined that the most effective parameter for Ra and F_d is the water pressure and then the stand-off distance.

The novel approach is to reduce cost and the time spent by using Taguchi optimization as a result of AWJ drilling the material in this fiber orientation [0°/90°]_s.

The purpose of this study is to investigate the impact of titanium oxide (TiO₂) filler on the abrasive wear properties of bamboo fiber reinforced epoxy composites (BFRCs) using a Taguchi approach. The study aims to enhance the abrasive wear resistance of these composites by introducing TiO₂ filler as a potential reinforcement, thus contributing to the development of sustainable and environmentally friendly materials.

This study focuses on the fabrication of epoxy/bamboo composites infused with TiO₂ particles within the Wt.% range of 0–8 Wt.% using hand layup techniques. The resulting composites were subjected to wear testing according to ASTM G99-05 standards. Statistical analysis of the wear results was carried out using the Taguchi design of experiments (DOE). Additionally, an analysis of variance (ANOVA) was used to determine the influential control factors impacting the specific wear rate (SWR) and coefficient of friction (COF).

The study illuminates how integrating TiO₂ filler enhances abrasive wear in epoxy/bamboo composites. Statistical analysis of SWR highlights abrasive grit size (grit) as the most influential factor, followed by normal load, Wt.% of TiO₂ and sliding distance. Analysis of the COF identifies normal load as the primary influential factor, followed by grit, Wt.% of TiO₂ and sliding distance. The Taguchi predictive model closely aligns with experimental results, validating its reliability. The morphological study revealed significant differences between the unfilled and TiO₂-filled composites. The inclusion of TiO₂ improved wear resistance, as evidenced by reduced surface damage and wear debris.

This research paper aims to integrate TiO₂ filler and bamboo fibers to create an innovative hybrid composite material. TiO₂ micro and nanoparticles show promise as filler materials, contributing to improved tribological properties of epoxy composites. The utilization of Taguchi’s DOE and ANOVA for statistical analysis provides valuable guidance for academic researchers and practitioners in optimizing control variables, especially in the context of natural fiber reinforced composites.

This paper aims to report the effect of titanium oxide (TiO₂) particles on the specific wear rate (SWR) of alkaline treated bamboo and flax fiber-reinforced composites (FRCs) under dry sliding condition by using a robust statistical method.

In this research, the epoxy/bamboo and epoxy/flax composites filled with 0–8 Wt.% TiO₂ particles have been fabricated using simple hand layup techniques, and wear testing of the composite was done in accordance with the ASTM G99-05 standard. The Taguchi design of experiments (DOE) was used to conduct a statistical analysis of experimental wear results. An analysis of variance (ANOVA) was conducted to identify significant control factors affecting SWR under dry sliding conditions. Taguchi prediction model is also developed to verify the correlation between the test parameters and performance output.

The research study reveals that TiO₂ filler particles in the epoxy/bamboo and epoxy/flax composite will improve the tribological properties of the developed composites. Statistical analysis of SWR concludes that normal load is the most influencing factor, followed by sliding distance, Wt.% TiO2 filler and sliding velocity. ANOVA concludes that normal load has the maximum effect of 31.92% and 35.77% and Wt.% of TiO2 filler has the effect of 17.33% and 16.98%, respectively, on the SWR of bamboo and flax FRCs. A fairly good agreement between the Taguchi predictive model and experimental results is obtained.

This research paper attempts to include both TiO₂ filler and bamboo/flax fibers to develop a novel hybrid composite material. TiO₂ micro and nanoparticles are promising filler materials, it helps to enhance the mechanical and tribological properties of the epoxy composites. Taguchi DOE and ANOVA used for statistical analysis serve as guidelines for academicians and practitioners on how to best optimize the control variable with particular reference to natural FRCs.