Search results

To investigate the effects of the infra‐red power level on sintering behaviour in the high speed sintering (HSS) process.

Single‐layer parts were produced using the HSS process, in order to determine the effect of the infra‐red power level on the maximum achievable layer thickness, and the degree of sintering. The parts were examined using both optical microscopy and contact methods.

It was initially expected that an increase in the infra‐red lamp powder might allow an increase in the depth of sintering that could be achieved, as a result of increased thermal transfer through the powder. However, results in fact indicated that there is a maximum layer thickness that can be achieved, as a result of part shrinkage in the z direction. Optical microscopy images have shown that a greater degree of sintering occurs at higher power levels, which would be expected to correspond to an improvement in the mechanical properties of the parts produced. These images also indicate that the radiation absorbing material forms in small “islands” on the powder bed surface. As sintering progresses, these islands begin to merge; this occurs to a greater extent at higher infra‐red lamp powers.

These results are based only on single layer parts. Further work will examine the sintering characteristics of multiple layer parts.

Results have shown that, whilst it is not possible to increase the achievable layer thickness of the parts produced by modifying the infra‐red lamp power, the degree of sintering can be improved greatly by increasing the power.

HSS is an entirely new process which is currently still under development; the results presented here will directly impact the direction of further development and research into this process.

The amount of radiated energy is known to be a crucial parameter in powder-bed additive manufacturing (AM) processes. The role of irradiance in the multijet fusion (MJF) process has not been addressed by any previous research, despite the key role of this process in the AM industry. The aim of this paper is to explore the relationship between irradiance and dimensional accuracy in MJF.

An experimental activity was carried out to map the relationship between irradiance and dimensional accuracy in the MJF transformation of polyamide 12. Two specimens were used to measure the dimensional accuracy on medium and small sizes. The experiment was run using six different levels of irradiance. For each, the crystallinity degree and part density were measured.

Irradiance was found to be directly proportional to part density and inversely proportional to crystallinity degree. Higher irradiance leads to an increase in the measured dimensions of parts. This highlights a predominant role of the crystallisation degree and uncontrolled peripherical sintering, in line with the previous literature on other powder-bed AM processes. The results demonstrate that different trends can be observed according to the range of sizes.

This paper aims to present a survey concerning the accuracy of thermoplastic polymeric parts fabricated by additive manufacturing (AM). Based on the scientific literature, the aim is to provide an updated map of trends and gaps in this relevant research field. Several technologies and investigation methods are examined, thus giving an overview and analysis of the growing body of research.

Permutations of keywords, which concern materials, technologies and the accuracy of thermoplastic polymeric parts fabricated by AM, are used for a systematic search in peer-review databases. The selected articles are screened and ranked to identify those that are more relevant. A bibliometric analysis is performed based on investigated materials and applied technologies of published papers. Finally, each paper is categorised and discussed by considering the implemented research methods.

The interest in the accuracy of additively manufactured thermoplastics is increasing. The principal sources of inaccuracies are those shrinkages occurring during part solidification. The analysis of the research methods shows a predominance of empirical approaches. Due to the experimental context, those achievements have consequently limited applicability. Analytical and numerical models, which generally require huge computational costs when applied to complex products, are also numerous and are investigated in detail. Several articles deal with artificial intelligence tools and are gaining more and more attention.

The cross-technology survey on the accuracy issue highlights the common critical aspects of thermoplastics transformed by AM. An updated map of the recent research literature is achieved. The analysis shows the advantages and limitations of different research methods in this field, providing an overview of research trends and gaps.

The purpose of this study was to assess the suitability of micro-computed tomography as a non-destructive method to investigate the morphology of nylon 12 parts produced by high-speed sintering (HSS). The investigation of the effect of changes in the lamp power on the properties of the fabricated parts was another purpose of this study.

Nylon 12 parts were manufactured using HSS with various lamp powers. Morphological properties of the parts were measured using micro-computed tomography. Ultimate tensile strength, elongation at break and Young’s modulus of the prepared parts were determined and compared. The effect of lamp power on the properties of the parts was then studied.

This paper proposes micro-computed tomography as a suitable technique to study the 3D structure of the parts produced by HSS. The effects of lamp power on the properties of the produced parts were also discussed.

The findings could result in an improvement in customisation of the parts for various applications through varying the lamp power. The level of lamp power could be tailored to obtain suitable part properties for a target application.

This study strengthens the fact that HSS is a promising additive manufacturing technique to produce nylon 12 parts, and the properties of the parts could be maximised using a suitable level of lamp power. The results showed that micro-computed tomography could be used as an efficient technique to investigate the morphology of the sintered parts.

This study aims to demonstrate for the first time that the cheap, commodity polymer, poly(propylene), can be successfully processed using high speed sintering, and that it can be recycled several times through the process, with little to no detriment to either the polymer itself or the parts obtained. This is significant as a step towards the realisation of high speed sintering as a technology for high-volume manufacturing.

A poly(propylene) powder designed for laser sintering was used to build parts on a high speed sintering machine. The unsintered powder was then collected and reused. Repeating this process allowed creation of seven generations of aged powder. A variety of characterisation techniques were then used to measure polymer, powder and part properties for each generation to discern any effects arising from ageing in the machine.

It was found that poly(propylene) could be used successfully in high speed sintering, albeit with a low build success rate. Increased powder age was found to correlate to an increase in the build success rate, changes in microscopic and bulk powder properties and improvement to the dimensional accuracy of the parts obtained. By contrast, no discernible correlations were seen between powder age and polymer molecular weight, or between powder age and the tensile properties of parts.

This is the first report of the use of poly(propylene) in high speed sintering. It is also first study regarding powder recyclability in high speed sintering, both in general and using poly(propylene) specifically.