Search results

Ti-Al composite plates have been used in aerospace and other important fields for specific purposes in recent years. However, relatively few studies have concentrated on Ti-Al additive manufacturing because during additive manufacturing process the local fusion and mixing of Ti/Al are inevitable. These areas where Ti and Al are mixed locally, especially interface, could easily generate high residual stresses and cracks. This study aims to manufacture Ti-Al functionally graded material and investigate the interaction of interface.

In this study, Ti6Al4V/AlSi10Mg functionally graded materials were fabricated by laser based directed energy deposition (L-DED) and a strategy using V interlayer to relieve interfacial stress was investigated.

The area between the two materials was divided into transition zone (TZ) and remelting zone (RZ). The phase distribution, microstructure and micro-Vickers hardness of the TZ and RZ were investigated. Typical intermetallic compounds (IMCs) such as TiAl3, Ti3Al and Ti5Si3 were found in both composites. The addition of V interlayer promoted the homogenization of IMCs near interface and led to the formation of new phases like V5Si3 and Al3V.

The solidification process near the interface of Ti-Al functionally graded material and the possible generation of different phases were described. The result of this paper proved the feasibility of manufacturing Ti-Al functionally graded material by L-DED.

Additive manufacturing is a fabrication technology with flexibility and economy. 18Ni300 is one of maraging steels with ultra-high strength, superior toughness, so it is an excellent candidate of structural material. This paper aims to explore the feasibility of using direct laser metal deposition method to fabricate18Ni300, and the evolution of its microstructure and defects is studied.

The experiments were conceived from single-trace-single-layer (STSL) test to multi-trace-multi-layers (MTML) test via single-trace-multi-layers (STML) test. The microstructure, defects and mechanical properties were analyzed.

The STML results showed that the columnar/equiaxed transformation occurred at the top part and the grain size increased with the layer number increasing, and it was explained by an innovative attempt combining columnar/equiaxed transformation model and the change of grain size. The MTML test with the interlayer orthogonal parallel reciprocating scanning pattern resulted in the grain growing along orthogonal directions; with the increase of overlap rate, the length and the area of the columnar grain decreased. What is more, the later deposition layer had lower micro-hardness value because of heat history.

Direct laser metal deposition method was a novel additive manufacturing method to manufacture 18Ni300 components, as 18Ni300 maraging steel was mainly manufactured by selective laser melting (SLM) method nowadays. It was useful to manufacture maraging steel parts using direct laser deposition method because it could manufacture larger parts than SLM method. Influence of processing parameters on forming quality and microstructure evolution was studied. The findings will be helpful to understand the forming mechanism of laser additive manufacturing of 18Ni300 components.

This paper aims to explore the influences of different process parameters, including laser power, scanning speed, defocusing distance and scanning mode, on the shape features of molten pool and, based on the obtained relationship, realize the diagnosis of forming defects during the process.

Molten pool was captured on-line based on a coaxial CCD camera mounted on the welding head, then image processing algorithms were developed to obtain melt pool features that could reflect the forming status, and it suggested that the molten pool area was the most sensitive characteristic. The influence of the processing parameters such as laser power, traverse speed, powder feed rate, defocusing distance and the melt pool area was studied, and then the melt pool area was used as the characteristic to detect the forming defects during the cladding and additive manufacturing process.

The influences of different process parameters on molten pool area were explored. Based on the relationship, different types of defects were accurately detected through analyzing the relationship between the molten pool area and time.

The findings would be helpful for the quality control of laser additive manufacturing.

The purpose of this paper is to predict and control the composition during laser additive manufacturing, since composition control is important for parts manufactured by laser additive manufacturing. Aluminum and steel functionally graded material (FGM) were manufactured by laser metal deposition, and the composition was analyzed by means of spectral analysis simultaneously.

The laser metal deposition process was carried out on a 5 mm thick 316L plate. Spectral line intensity ratio and plasma temperature were chosen as two main spectroscopic diagnosis parameters to predict the compositional variation. Single-trace single-layer experiments and single-trace multi-layer experiments were done, respectively, to test the feasibility of the spectral diagnosis method.

Experiment results showed that with the composition of metal powder changing from steel to aluminum, the spectral intensity ratio of the characteristic spectral line is proportional to the elemental content in the plasma. When the composition of deposition layers changed, the characteristic spectrum line intensity ratio changed obviously. And the linear chemical composition analysis results confirmed the gradient composition variation of the additive manufacturing parts. The results verified the feasibility of composition analysis based on spectral information in the laser additive manufacturing process.

The composition content of aluminum and steel FGM was diagnosed by spectral information during laser metal deposition, and the relationship between spectral intensity and composition was established.