Search results

To fabricate submicrometer thin membrane of silicon nitride and silicon dioxide over an anisotropically etched cavity in (100) silicon.

PECVD of silicon dioxide and Silcion nitride layers of compatible thicknesses followed by thermal annealing in nitrogen ambients at 1,000°C for 30 min, leads to stable membrane formation. Anisotropic etching of (100) silicon below the membrane through channels on the sides has been used with controlled cavity dimensions.

Lateral front side etching through channels slows down etching rate drastically. The etching mechanism has been discussed with experimental details.

Vacuum sealed cavity membranes can be realised for micro sensor applications.

The process is new and feasible for micro sensor technologies.

The purpose of this paper is to use finite element method for optimizing the membrane type double cavity vacuum sealed structure for the best achievable sensitivity in a piezoresistive absolute pressure sensor and its validation using a standard complementary metal oxide semiconductor (CMOS) process.

A double cavity vacuum sealed piezoresistive absolute pressure sensor has been simulated and optimized for its performance and an analytical model describing the behaviour of the sensor has been described. The 1×1 mm sensor chip has two membrane type 100×30×1.7 μm diaphragms consisting of composite layers of plasma enhanced chemical vapour deposition (PECVD) of silicon nitride (Si₃N₄) and silicon dioxide (SiO₂) each hanging over 21 μm deep rectangular cavity. Potassium hydroxide (KOH) based anisotropic etching of single crystal silicon using front side lateral etching technology is used for the fabrication of the sensor. The electrical readout circuitry uses 318 Ω boron diffused low pressure vapour chemical vapour deposition (LPCVD) of polysilicon resistors arranged in the Wheatstone half bridge configuration. The sensing structure is simulated and optimized using COMSOL Multiphysics.

Front-side lateral etching technology has been successfully used for the fabrication of double cavity absolute pressure sensor. A good agreement with the fabricated device for the chosen location of the piezoresistors through simulation has been predicted. The measured pressure sensitivity of two tested pressure sensors is 12.63 and 12.46 mV/MPa, and simulated pressure sensitivity is found to be 12.9 mV/MPa for pressure range of 0 to 0.5 MPa. The location of the piezoresistor has also been optimized using the simulation tools for enhancing the sensor sensitivity to 62.14 mV/MPa. The pressure sensitivity is further enhanced to 92 mV/MPa by increasing the width of the diaphragm to 35 μm.

The simulated and measured pressure sensitivities of the double cavity pressure sensor are in close agreement. Sevenfold enhancement in the pressure sensitivity of the optimized sensing structure has been observed. The proposed front-side lateral etching technology can be adopted for making membrane type diaphragms hanging over vacuum sealed micro-cavities for high sensitivity pressure sensing applications.

The purpose of this paper is to describe the fabrication of a miniaturized membrane type double cavity vacuum‐sealed micro sensor for absolute pressure using front‐side lateral etching technology.

Potassium hydroxide‐based anisotropic etching of single crystal silicon is used to realize the cavities under the membrane type diaphragms through channels on the sides. The diaphragms consist of composite layers of plasma‐enhanced chemical vapour deposition (PECVD) of silicon nitride and silicon dioxide. PECVD of silicon dioxide is done for sealing the channels and the cavity in vacuum. Boron thermal diffusion in low‐pressure chemical vapour deposition of polysilicon layer over the membrane is done for realizing resistors. The fabricated device uses Wheatstone half bridge circuit to read the variation of resistance with respect to an applied pressure.

A double cavity vacuum‐sealed absolute pressure micro sensor has been fabricated successfully using front‐side lateral etching technology and has been measured for pressure range of 0‐0.45 MPa. The measured pressure sensitivity of two pressure sensors is 9.28 and 10.44 mV/MPa.

The paper shows that front‐side lateral etching technology is feasible in the fabrication of small vacuum‐sealed cavities and absolute pressure sensors.