Search results

A numerical simulation study of a Tandem solar cell is presented. The parameters of single and two-diodes lumped-circuit model are usually the saturation current, the series resistance, the ideality factor, the shunt resistance and the photocurrent. It is found that the influence of the distributed series resistance on electrical characteristics can be described numerically by the application of the two models to Tandem organic solar cells. A description of the efficiency, fill factor, open circuit voltage and short circuit current on the devices are marked with series resistance, temperature and ideality factor. This approach allows one to obtain a set of parameters which is reasonable and representative of the physical system.

A literature review revealed that in recent times, many companies have attempted organization‐wide change management through the philosophy and principles of Lean Thinking (LT). Although some organizations have transformed and reaped significant benefits in this endeavour, many organizations have failed in this attempt. One of the reasons can be attributed to the fact that not many organizations are attempting to “assess the organizational readiness” before implementing/adapting LT. This paper aims to address this issue.

Hence in this paper, an attempt has made to address this problem by presenting a hypothetical case study of an Indian organization to comprehensively assess organizational readiness of the case organisation using a graph theoretic approach (GTA), which has the ability to integrate and model multiple inter‐related factors.

From the obtained results, it was found that the case organization is not fully ready to embrace LT. It needs to work on different factors under the categories of suppliers, customers, etc. in addition to employees, organisation and top management for smooth and successful adaptation.

According to the authors' knowledge, no paper exists either in the literature of organizational analysis or in the field of LT literature that demonstrates the application of GTA, specifically for assessing the readiness of an organization in adapting LT. Furthermore, various factors which need to be considered were identified apart from modelling them by incorporating the relationship/dependency that exists between these factors, which is unique.

In the M'Zab Valley, women have long remained confined to their domestic sphere and are invisible in outdoor spaces. This study aims to analyse the use of public and private spaces by the women of Ksar El Atteuf, particularly after the significant changes that society has undergone.

This study examines the role of gender in the daily life of an urban community in the M'Zab Valley in Algeria through semi-structured interviews with relevant experts and a survey of 100 Mozabite women. It focuses on their roles and views regarding using spaces and maintaining Mozabite heritage.

Social and religious norms influence women's utilisation, behaviour and roles in gendered spaces. Most women consider their place to be within the house but refuse to live primitively. Education and work have enabled them to emerge outdoors. The results also showed that owing to the restrictions imposed on women, 60% of them emphasised the need to express their opinions and make decisions, and 26% asked for more opportunities and spaces.

This study broadens understanding of Mozabite society and its architectural and urban heritage. The empirical study surveyed women and conducted interviews with experts. This is valuable, particularly, given the challenges of studying gender in conservative cultural settings.

The purpose of this paper is to analyze the liquid sloshing behaviors in two-dimensional tanks with various porous baffles under the external excitation.

Adopting the finite element method (FEM) and control variable method to study the impacts of the height, length, number, location, shape, porous-effect parameter of the porous baffle, the external load frequency and the shape of the tank on the liquid sloshing response.

The amplitude of the free surface can be reduced effectively when the baffle opening is appropriate. The anti-sway ability of the system increases in pace with the baffle’s height growing. Under the same conditions, the shapes of the baffles have an important effect on improving the anti-sway ability of the system.

As there exist the differences of the velocity potential between each side of the porous baffle, which means that there are two different velocity potentials at a point on the porous baffle, the conventional finite element modeling technologies are not suitable to be applied here. To deal with this problem, the points on the porous baffle are regarded as two nodes with the same coordinate to model and calculate.

This study aims to provide a new method for precisely sizing photovoltaic (PV) arrays for standalone, direct pumping PV Water Pumping (PVWP) systems for irrigation purposes.

The method uses historical weather data and considers daily variability in regional temperatures and rainfall, crop evapotranspiration rates and seasonality effects, all within a nonparametric bootstrapping approach to synthetically generate daily rainfall and crop irrigation needs. These needs define the required daily supply of pumped water to achieve a user-specified level of reliability, which provides the input to an intuitive approach for PV array sizing. An economic comparison of the costs for the PVWP versus a comparably powered diesel generator system is provided.

Pumping 22.8646 m³/day of water would meet the pasture crop irrigation needs on a one-acre (4046.78 m²) tract of land in South Florida, with 99.9% reliability. Given the specified assumptions, an 8.4834 m² PV array, having a peak power of 1.1877 (kW), could provide the 1.2347 (kWh/day) of hydraulic energy needed to supply this volume over a total head of 20 meters. The PVWP system is the low-cost option when diesel prices are above $0.90/liter and total installed PV array costs are fixed at $2.00/Watt peak power or total installed PV array costs are below $1.50/Watt peak power and diesel prices are fixed at $0.65/liter.

Because the approach is not dependent on the shapes of the sampling distributions for regional climate factors and can be adapted to consider different types of crops, it is highly portable and applicable for precisely determining array sizes for standalone, direct pumping PVWP systems for irrigating diverse crop types in diverse regions.

Using turbulators, obstacles, ribs, corrugations, baffles and different tube geometry, and also various arrangements of these components have a noticeable effect on the shell and tube heat exchangers (STHEs) thermal-hydraulic performance. This study aims to investigate non-Newtonian fluid flow characteristics and heat transfer features of water and carboxyl methyl cellulose (H₂O 99.5%:0.5% CMC)-based Al₂O₃ nanofluid inside the STHE equipped with corrugated tubes and baffles using two-phase mixture model.

Five different corrugated tubes and two baffle shapes are studied numerically using finite volume method based on SIMPLEC algorithm using ANSYS-Fluent software.

Based on the obtained results, it is shown that for low-mass flow rates, the disk baffle (DB) has more heat transfer coefficient than that of segmental baffle (SB) configuration, while for mass flow rate more than 1 kg/s, using the SB leads to more heat transfer coefficient than that of DB configuration. Using the DB leads to higher thermal-hydraulic performance evaluation criteria (THPEC) than that of SB configuration in heat exchanger. The THPEC values are between 1.32 and 1.45.

Using inner, outer or inner/outer corrugations (outer circular rib and inner circular rib [OCR+ICR]) tubes for all mass flow rates can increase the THPEC significantly. Based on the present study, STHE with DB and OCR+ICR tubes configuration filled with water/CMC/Al₂O₃ with f = 1.5% and d_np = 100 nm is the optimum configuration. The value of THPEC in referred case was 1.73, while for outer corrugations and inner smooth, this value is between 1.34 and 1.57, and for outer smooth and inner corrugations, this value is between 1.33 and 1.52.

Microfluidics is one of the extensive elaborated technologies in thermal and engineering fields due to its wide range of applications, such as micro heat exchangers, micro mixture and microchannel heat sinks, which is used to develop a large number of microscopic devices and systems. Enhancement of thermal energy using verity of nanoliquids is one of the challenges in these applications of microfluidics. Therefore, using single wall carbon nanotubes for enhancement of thermal energy in microchannel is the main purpose of this study. Hall effect of natural convection flow in a vertical channel with slip and temperature jump condition is considered. The impacts of radiative heat flux, uniform heat source/sink, viscous dissipation and joule heating are also taken into account.

Suitable non-dimension variables are applied to the governing equations to reduce the system into ordinary differential equations. The reduced nonlinear system is then solved numerically using Runge–Kutta–Fehlberg fourth–fifth-order method along with shooting technique. The impact of different pertinent parameters on numerical solutions of primary velocity, secondary velocity, temperature, entropy generation and Bejan number is comprehensively discussed in detail. Also, the obtained numerical results are compared with existing one which perfectly found to be in good agreement.

It is established that, with the aspects of Joule heating, viscous dissipation, radiative heat flux and uniform heat source/sink, the production in the entropy can be improved. Further, it is found that the increasing ratio of wall ambient temperature difference and nanoparticle volume fraction leads to enhance the entropy generation. The same effect reverses with increasing values of fluid wall interaction parameter (FWIP) and rare faction. The irreversibility ratio enhances with larger values of nanoparticle volume fraction and decelerates with increment values of FWIP.

The impact of single wall carbon nanoliquid in a vertical channel flow by using radiative heat flux, heat source/sink, joule heating and viscous dissipation is first time investigated. Further, the influence of Hall current is explored in detail.

The purpose of this paper is the numerical investigation of the friction laws for incompressible flow in undulated channels, with emphasis on the applicability of the hydraulic diameter concept. A focal point of the study is the derivation of correlations to increase the accuracy of the hydraulic diameter approach.

Calculations are performed for laminar and turbulent flow, for Reynolds number ranges between 10–2,000 and 5,000–100,000. For turbulent flow, the shear stress transport (SST) model is used. A simple, sawtooth-like undulation shape is considered, where the channel geometry can be described by means of three length parameters. Letting each to take three values, totally 27 geometries are analyzed.

It is observed that the hydraulic diameter concept applied via analytical or empirical expressions to obtain friction coefficients does not lead to accurate results. For laminar flow, the maximum deviations of analytical values from predicted are about 70%, while 20% deviation is observed on average. For turbulent flow, deviations of Blasius correlation from predicted ones are smaller, but still remarkable with about 20% for maximum deviation and about 10% on average.

Applicability of the hydraulic diameter concept to undulated channels was not computationally explored. A further original ingredient of the work is the derivation of correlations that lead to improved accuracy in calculating the friction coefficient using hydraulic diameter. For laminar flow, the maximum and average deviations of present correlations from numerical predictions are below 5% and 2%, respectively. For turbulent flow, these numbers turn out to be approximately 12% for the maximum deviation and about 2% for the average.

The purpose of this study is to investigate the impact of varying baffle height and spacing distance on heat transfer and cooling performance of electronic components in a baffled horizontal channel, using a Cu-H₂O nanofluid under mixed convection and laminar flow.

The mathematical model is two-dimensional and comprises a system of four governing equations, such as the conservation of continuity, momentum and energy. To obtain numerical solutions for these equations, the finite volume method was used for discretization. A validation process was performed by comparing this study’s results with those of previously published studies. The comparison revealed a close agreement. The numerical study was performed for a wide range of key parameters: The baffle height (0 ≤ h ≤ 0.7), the spacing distance between baffle and blocks (0.25 ≤ w ≤ 3), the Grashof and Reynolds numbers are kept equal to 10⁴ and 75, respectively, the channel aspect ratio is L/H = 10, and the volume fraction of Cu nanoparticles is fixed at φ = 5%.

The results of the study reveal a significant improvement in heat transfer in terms of total Nusselt number of the top and bottom hot components, which exhibited an improvement of 16.89% and 17.23% when the baffle height increases from h = 0 to h = 0.7. Additionally, the study found that reducing the distance between the baffle and the electronic components up to a certain limit can improve the heat transfer rate. Therefore, the optimal height of the baffle was found to be no lower than 0.6, and the recommended distance between the heaters and the baffle was 0.5.

This study provides valuable insights into the optimization of the design of baffled channels for improved heat transfer performance. The findings of study can be used to improve heat exchangers and cooling systems in various applications. The use of Cu-H₂O nanofluid under mixed convection and laminar flow conditions in channel with baffle and electronic components is also unique, making this study an original contribution to the field.

The purpose of this paper is to investigate the heat transfer of laminar and turbulent pulsating Al203/water nanofluid flow in a two-dimensional channel. In the laminar flow range, with increasing Reynolds number (Re), the velocity gradient is increased. Also, the Nusselt number (Nu) is increased, which causes increase in the overall heat transfer rate. Additionally, in the change of flow regime from laminar to turbulent, average thermal flux and pulsation range are increased. Also, the effect of different percentage of Al₂O₃/water nanofluid is investigated. The results show that the addition of nanofluids improve thermal performance in channel, but the using of nanofluid causes a pressure drop in the channel.

The pulsatile flow and heat transfer in a two-dimensional channel were investigated.

The numerical results show that the Al₂O₃/Water nanofluid has a significant effect on the thermal properties of the different flows (laminar and turbulent) and the average thermal flux and pulsation ranges are increased in the change of flow regime from laminar to turbulent. Also, the addition of nanofluid improves thermal performance in channels.

The originality of this work lies in proposing a numerical analysis of heat transfer of pulsating Al₂O₃/Water nanofluid flow -with different percentages- in the two-dimensional channel while the flow regime change from laminar to turbulent.