Lovrenc Gašparin, Andrej Černigoj, Stojan Markič and Rastko Fišer
The purpose of this study is to estimate the sensitivity of cogging torque in permanent magnet (PM) motor designs due to PM assembly tolerance and/or PM imperfections and to…
Abstract
Purpose
The purpose of this study is to estimate the sensitivity of cogging torque in permanent magnet (PM) motor designs due to PM assembly tolerance and/or PM imperfections and to evaluate how such faults can be reliably detected in simulated and measured cogging torque signals.
Design/methodology/approach
PM motors exhibit inherent cogging torque, which creates torque ripple and prevents smooth rotation of the rotor, resulting in undesirable vibration and noise. While cogging torque minimization is necessary to improve PM motor performance, several FEM models have been developed to study and present data demonstrating the sensitivity of cogging torque to PM assemblies and/or PM imperfections. Some procedures that would predict and evaluate cogging torque components relative to measured PM positions on assembled PM motors were proposed.
Findings
On the basis of numerous performed simulations using different FEM models and experimental results on rotors from mass‐production, it was found and proved that PM assembly tolerance and/or PM imperfections cause the phenomenon of additional cogging torque harmonic components. Considering the presented theoretical aspects motor designers can predict which additional harmonic components will comprise the cogging torque, as a result of which the appropriate technique for minimizing native and additional harmonic components can be applied.
Research limitations/implications
The presented research of cogging torque sensitivity in different PM motor designs to assembly tolerance and/or PM imperfections should in future also consider stator irregularities and different methods of lamination stacking such as notches, welding, and interlocking.
Practical implications
By utilizing the presented method and considering recommendations, advanced motor designers have a reliable tool for predicting the order and level of additional harmonic components in total cogging torque. Thus, adequate critical manufacturing tolerances can be defined in order to achieve minimal waste in produced PM motors.
Originality/value
The originality of the paper is explained by the theoretical aspects and analytical equations of additional harmonic components in cogging torque of PM motors. Also original are the expressions for amplitude calculation of additional harmonic components influenced by manufacturing tolerances.
Details
Keywords
Lovrenc Gašparin, Andrej Černigoj and Rastko Fišer
The purpose of this paper is to estimate and evaluate how cogging torque in permanent magnet (PM) motor designs is sensitive to the number of applied interlocks in stator…
Abstract
Purpose
The purpose of this paper is to estimate and evaluate how cogging torque in permanent magnet (PM) motor designs is sensitive to the number of applied interlocks in stator back‐iron, which is a standard method for stator lamination stacking.
Design/methodology/approach
The PM motors exhibit inherent cogging torque, which creates torque ripple and prevents smooth rotation of the rotor resulting in undesirable vibration and noise. While cogging torque minimization is necessary to improve PM motor performance, several FEM models have been developed to study and present data demonstrating sensitivity of the cogging torque to the applied interlocks. A procedure that would predict and evaluate cogging torque components relative to chosen number and positions of interlocks was proposed.
Findings
On the basis of theoretical considerations, which were verified by numerous performed simulations using different FEM models, it was found out and proved that interlocks in the stator back‐iron cause the phenomenon of additional cogging torque harmonic components (AHC). Taking into account presented theoretical aspects motor designers can predict, which AHC will comprise the cogging torque. Each motor design has its own optimal value of interlocks, therefore a precise study should be performed during the design process.
Practical implications
By utilizing presented method and considering recommendations, advanced designers of PM motors will have a reliable tool for predicting the order and the level of AHC in total cogging torque due to the stator lamination stacking methods.
Originality/value
The paper presents theoretical aspects and analytical equations of AHC of PM motors. So far, the authors dealing with the cogging torque of the PM motors did not take into account the influence of the stator lamination stacking method on the level of torque oscillations. The new contribution is also the study of the sensitivity of different motor designs to the number and position of interlocks, which enables the minimization of the AHC in order to fulfil stringent market demands for low‐cogging torque level.
Details
Keywords
Lovrenc Gašparin, Andrej Černigoj and Rastko Fišer
The purpose of this paper is to present the dependence of the level and harmonic structure of the cogging torque in permanent magnet synchronous motors (PMSM) to interlocks and…
Abstract
Purpose
The purpose of this paper is to present the dependence of the level and harmonic structure of the cogging torque in permanent magnet synchronous motors (PMSM) to interlocks and notches in a stator back iron, which are standard methods for stator lamination stacking in mass‐production.
Design/methodology/approach
Methods of stacking up the lamination like welding or interlocking are introducing magnetic asymmetries in stator back iron which causes additional harmonic components (AHC). A finite element method and Fast Fourier transform were used to calculate cogging torque harmonic components (HC) with regard to the applied number and positions of interlocks and notches. All simulation results were verified by laboratory tests.
Findings
It has been established and proved that technologies for stacking lamination packs cause local saturation peaks in back iron which give rise to additional cogging torque AHC and consequently increase the total cogging torque. It is also shown that the magnetic properties of interlocks cannot be simply considered as air regions but adequate relative permeability of such affected soft magnetic material must be determined to improve the accuracy of FEM calculations.
Practical implications
Considering presented results, it is possible to foresee which AHC will include the cogging torque of mass‐produced PMSMs due to the stator lamination stacking methods. In this way, the optimal stacking method can be selected in order to minimize the effect of AHC.
Originality/value
So far, authors dealing with the cogging torque have not taken into account the influence of the stator lamination stacking method on the level of torque oscillations.
Details
Keywords
Martin Furlan, Andrej Cernigoj and Miha Boltezar
In this article, we present an investigation into the sound radiation from a permanent‐magnet DC electric motor using the finite‐element (FE) and boundary‐element (BE) models. A…
Abstract
In this article, we present an investigation into the sound radiation from a permanent‐magnet DC electric motor using the finite‐element (FE) and boundary‐element (BE) models. A three‐times‐coupled electromagnetic‐mechanical‐acoustic numerical model was set‐up to predict the acoustic field. The first stage was to calculate the magnetic forces that excite the structure of the motor by using the FEM. In the second stage, the exciting magnetic forces were applied to the structural model, where the harmonic analysis was carried out using the FEM. The last stage was to model the acoustics by using the BEM. In order to evaluate the numerical model, the computational results were compared with the vibration and acoustic measurements and a reasonable agreement was found.