Search results

The purpose of the study was to develop a performance flat-plate solar collector that would be used as a solar drier for fruit fig (Ficus carica L). This study proposes how and why solar energy is important for drying the agricultural products. This study aims to expand the domain of solar collector for different purposes and, most important, for agricultural resource normally found in the literature.

The paper opted for an exploratory study using the flat-plate solar collector with drying chamber for drying purposes of agricultural products. During the experiment, the data were collected with moisture content, drying rate of the product and solar irradiation falls on the collector.

This paper describes that how flat-plate collector works for agricultural products and how to reduce the moisture content in the product (fig). Efficiency of collector was evaluated under the ambient temperatures of 24°C. Efficiency also significantly increased from 53 to 55 per cent with an increase in ambient temperature from 22 to 24 °C. Figs (Ficus carica L) were dried in the drying chamber of the flat-plate solar collector. The products were dried at temperature of 55-65°C and 15 to 20 per cent humidity.

Because of this research chosen, the research results are beneficiary for agricultural users for drying purposes. Therefore, the researchers are encouraged to dry the agricultural product with flat-plate solar collector, because it reduced the moisture content of the product very fast.

This paper fulfills an identified need to study that how flat-plat solar collector can be used.

To cover the main contributions and developments in solar thermal collectors through focusing on materials, heat transfer characteristics and manufacturing challenges.

A range of published papers and internet research including research work on various solar thermal collectors (flat plate, evacuated tubes, and heat pipe tube) were used. Evaluation of solar collectors performance is critiqued to aid solar technologies make the transition into a specific dominant solar collector. The sources are sorted into sections: finding an academic job, general advice, teaching, research and publishing, tenure and organizations.

Provides information about types of solar thermal collectors, indicating what can be added by using evacuated tube collectors instead of flat plate collectors and what can be added by using heat pipe collectors instead of evacuated tubes.

Focusing only on three types of solar thermal collectors (flat plate, evacuated tubes, and heat pipe tube).

Useful source of information for consultancy and impartial advice for graduate students planning to do research in solar thermal technologies.

This paper fulfils identified information about materials and heat transfer properties of materials and manufacturing challenges of these three solar thermal collectors.

One of the existing and commonly used solar energy harvesting devices is the parabolic trough solar collector (PTSC). Because of their ability to operate in low and medium temperatures, parabolic trough concentrators are widely used in power generation plants and industrial process heating applications. Therefore, the investigation of how different operating conditions affect these devices’ overall efficiency has received a great deal of attention in the recent decade. This study aims to enhance the thermal performance of the PTSC and reduce the system cost.

In the novel configuration, a noncirculated nanofluid absorbs solar radiation through a glass wall. The base fluid was synthetic oil (5W30), and the nanoparticles used were copper oxide. The heat captured is immediately absorbed by the water circulating inside the copper tube immersed in the nanofluid. ANSYS FLUENT 15.0 was used for carrying out computational fluid dynamics simulations for two models of single and triple copper tubes. The experimental results obtained from a test rig constructed for this purpose were compared with the numerical outcomes of the single copper tube model.

The findings of the simulation demonstrated that performance was superior for the single copper tube model over the triple copper tube model. The numerical findings of the single copper tube model were compared with the experimental results. The numerical and experimental results differed from 3.17% to 5.6%. Investigations were carried out to study the effects of varying the volumetric flow rate of (20, 40, 60 and 80 L/h) and water inlet temperatures of (300, 315 and 330 K) on the effectiveness and performance of the newly developed model. Additionally, two nanofluid volume fractions of 0.05% and 0.075% were used for investigating their effect on the performance of the novel configuration. According to the findings, the highest thermal efficiency of 55.31% was recorded at 0.075% concentration and 80 L/h volume flow rate.

In this study, a novel direct absorption solar collector configuration using a noncirculated nanofluid was designed to enhance the thermal efficiency of PTSC. This new approach makes it possible to boost the thermal performance of the PTSC and lower the system’s cost.

In this study, the effects of using corrugated absorber plate (instead of flat plate) and also using aerosol/carbon-black nanofluid (instead of air) on heat transfer and turbulent flow characteristics in solar collectors were numerically investigated.

The 3D continuity, momentum and energy equation were solved by finite volume and SIMPLE algorithm. As a result, the corrugated absorber plate was inspected in the case of triangle, rectangle and sinuous with the wave length of 1 mm and wave amplitude of 3 mm in turbulent flow regime and Reynolds number between 2,500 and 4,000. Choosing the proper geometry was carried out based on the best performance evaluation criteria (PEC) and increasing the air temperature from collector inlet to outlet.

The results revealed that for all times of the year the highest PEC was obtained for corrugated Sinusoidal model; however, the highest temperature increase from inlet to outlet was obtained for rectangular corrugated model. In addition, the results indicated that in sinusoidal model, the nanoparticles volume fractions increase leads to heat performance coefficient increase and the best heat performance conditions were attained in volume fraction of 0.1 per cent and Reynolds number of 4,000 for both six months period. In model with rectangular corrugated plate, usage of nanofluid in all range of Reynolds numbers leads to reduction of outlet temperature.

The effect of some nanoparticles on heat transfer using thermal– hydraulic performances in heat exchangers has been assessed, but the effects of atmospheric aerosol-based nanofluid using carbon-black nanoparticles (CBNPs) on the heat transfer in corrugated heat sink solar collectors by 3D numerical modeling has not been yet investigated. In present study, usage of CBNPs with different volume fractions in range of 0 to 0.1 per cent in turbulent regime of fluid flow is analyzed. Furthermore, in this paper, besides the effects of using CBNPs, a solar absorber located in Shiraz, as one of the best solar irradiation receiver cities in Iran is evaluated.

This study begins by outlining the core principles of how flat plate solar collectors (FPSC) operate and the underlying mechanisms of heat transfer. It underscores the pivotal role of fin patterns in enhancing convective heat transfer.

The primary objective is to examine the impact of diverse fin patterns on the thermal performance of FPSCs. The study involves the development of a 3D-CFD model for FPSC using the computational fluid dynamics (CFD) software ANSYS FLUENT. The analysis is conducted for variable mass flow rates (m_f) ranging from 0.01 to 0.05 kg/s with an interval of 0.02 kg/s. Each flow rate is assessed for three distinct fin patterns: straight plate fins, V-shaped fins and wavy fins. Recognizing the variation in solar radiation intensity throughout the day, the analysis is executed at six different time points ranging 10:00 a.m. to 03.00 p.m. with a time interval of 1.00 h.

It is observed that the wavy fin pattern with a mass flow rate of 0.01 kg/s exhibited the highest outlet temperature, showing a significant temperature difference of 12.4 K at noon. Conversely, the V-shaped fin pattern with a mf of 0.05 kg/s has the lowest temperature difference value, measuring only 3 K. The analysis included the calculation of thermal efficiency for each case, revealing that the V-shaped fin pattern at a mf of 0.05 kg/s and a sun radiation intensity of 885.42 W/m² achieved the maximum instantaneous thermal efficiency (η_th) of 34.7%. The study records the outlet air temperature for all of these combinations and presents the data graphically in the paper.

The findings of the simulations indicate that the thermal performance that is η_th and maximum temperature of outlet air of FPSCs can be improved through the utilization of variable fin patterns.

The roofs of houses located at middle latitudes receive significant solar radiation useful to supply their own energy demands and to feed back into the urban electricity network. However, solar panels should be properly integrated into roofs. This study analyzed roof geometry and integrated solar performance of Photovoltaic, thermal-photovoltaic, and hybrid solar collection technologies on dwelling cases selected from a sample of recent housing developments in Concepción, Chile. Hour-by-hour energy generation estimates and comparisons with demand levels were calculated for representative days during seasons of maximum, minimum as well as mid-season. These estimates took into account the roof tilt and orientation effects also. Trnsys@ software was used to determine electricity supply and F-Chart tool for thermal energy supply. The results show five times more panels can be placed on the largest and most regular shaped roof sections than on those with the smallest and most irregular shapes. The house model with the largest roof section can provide up to six times more energy than the model with the smallest second roof section in different seasons and systems. This paper thus provides new findings on the performance of solar technologies when related to home energy demands and roof geometry.

Low flow bikini solar combisystems and high flow tank‐in‐tank solar combisystems have been studied theoretically. The aim of this paper is to study which of these two solar combisystem designs is suitable for different houses. The thermal performance of solar combisystems based on the two different heat storage types is compared.

The thermal performance of Low flow bikini solar combisystems and high flow tank‐in‐tank solar combisystems is calculated with the simulation program TRNSYS. Two different TRNSYS models based on measurements were developed and used.

Based on the calculations it is concluded that low flow solar combisystems based on bikini tanks are promising for low energy buildings, while solar combisystems based on tank‐in‐tank stores are attractive for the houses with medium heating demand and old houses with high heating demand.

Many different Solar Combisystem designs have been commercialized over the years. In the IEA‐SHC Task 26, twenty one solar combisystems have been described and analyzed. Maybe the mantle tank approach also for solar combisystems can be used with advantage? This might be possible if the solar heating system is based on a so‐called bikini tank. Therefore, the new developed solar combisystems based on bikini tanks is compared to the tank‐in‐tank solar combisystems to elucidate which one is suitable for three different houses with low energy heating demand, medium and high heating demand.

Because of its increased absorptance in fluid and reduced heat loss, direct absorption nanofluid (DANF) is receiving intense interest as an efficient way to harvest solar energy. This work aims to investigate, for the first time, the application of DANF in parabolic trough collectors (PTC), a promising collector for solar thermal systems.

A representative flow and heat transfer study of different fluids in a straight tube is conducted, and the basic energy equation and radiative transfer equations are numerically solved to obtain the fluid temperature distribution and energy conversion efficiency. Ethylene glycol (EG) and different concentrations of (i.e., 0.1-0.6 per cent) multi-wall carbon nanotubes (MWCNT) in EG are used as sample fluids. Four cases are studied for a traditional PTC (i.e., using metal tube) and a direct absorption PTC (i.e., using transparent tube) including a bare tube, a tube with an air-filled glass envelope and a tube with vacuumed glass envelop. The numerical results are verified by an experimental study using a copper-glass absorber tube, which reveals the good potential of DANFs.

Compared with a conventional PTC, using DANF shows an increase of 8.6 per cent and 6.5 K, respectively, in thermal efficiency and outlet temperature difference at a volume fraction (0.5 per cent) of nanoparticles. The results also show that the improvement in solar efficiency increases with increasing particle concentrations, and the vacuum insulated case has the highest efficiency.

In all previous studies, an important section was missing as the effect of photons on the direct solar absorption trough collector, which is considered in this study. This paper proposes a new concept of using direct solar absorption nanofluids for concentrated solar collectors and analyzes the performance of both absorptance and transmittance efficiency considerations. To reveal the potential of the new concept, an analytical model based on energy balance is developed, and two case studies are performed.

The purpose of this paper is to present and discuss the external factors of the solar dryer design that influenced the thermal efficiency of the solar dryer that contribute to the better quality of dried food products.

From the reviewed works of literature, the external factors including the drying temperature, airflow rate and relative humidity have significant effects to increase the rate of moisture diffusivity of the freshly harvested products during the drying process. The proper controls of airflow rate (Q), velocity (V), relative humidity (RH%) and drying temperature (°C) can influence the dried product quality. The dehydration ratio is the procedure to measure the quality of the dried food product.

The indirect solar dryer including the mixed-mode, hybrid and integrated was found shorter in drying time and energy-intensive compared to sun drying and direct drying. The recommended drying temperature is from 35.5°C to 70°C with 1–2 m/s velocity and 20%–60% relative humidity. The optimum thermal efficiency can be reached by additional devices, including solar collectors and solar accumulators. It gives a simultaneous effect and elongated the drying temperature 8%–10% higher than ambient temperature with 34%–40% energy saving. The recommended airflow rate for drying is 0.1204 to 0.0894 kg/s. Meanwhile, an airflow rate at 0.035–0.04 kg/m2 is recommended for an optimum drying kinetic performance.

This paper discusses the influence of the external factors of the solar dryer design on the thermal performance of the solar dryer and final dried food products quality. Therefore, the findings cannot serve as a statistical generalization but should instead be viewed as the quantitative validation subjected to fundamentals of the solar dryer design process and qualitative observation of the dried food product quality.

A well-designed of solar dryer with low operating and initial fabrication cost, which is simple to operate is useful for the farmers to preserve surplus harvested crops to an acceptable and marketable foods product. The optimization of the external and internal factors can contribute to solar dryer thermal performance that later provides an organoleptic drying condition that results in good quality of dried product and better drying process. The recommended drying temperature for a drying method is between 35°C up to 70°C. Drying at 65.56°C was effective to kill microorganisms. Meanwhile, drying at 50°C consider as average drying temperature. The recommended airflow rate for drying is 0.1204 to 0.0894 kg/s. Meanwhile, air flowrate at 0.035–0.04 kg/m² is recommended for optimum drying kinetic performance. The recommended value of aspect ratio and mass flow rate is 200 to 300 for an optimum evaporation rate. The good quality of dried products and good performance of solar dryers can be developed by proper control of airflow rate (Q), velocity (V), relative humidity (RH%) and drying temperature (°C).

The proper control of the drying temperature, relative humidity and airflow rate during the drying process will influence the final dried food products in terms of shape, color, aroma, texture, rupture and nutritious value. It is crucial to control the drying parameters because over-drying caused an increment of energy cost and reduces the dry matter. The quick-drying will disturb the chemical process during fermentation to be completed.

This study identifies the potential of the solar drying method for dehydrating agricultural produces for later use with the organoleptic drying process. The organoleptic drying process can reduce mold growth by promising an effective diffusion of moisture from freshly harvested products. The research paper gives useful understandings that well-designed solar drying technology gives a significant effect on dried product quality.

Energy security is a major concern for India and many rural areas remain un-electrified. Thus, innovations in sustainable technologies to provide energy services are required. Biomass and solar energy in particular are resources that are widely available and underutilised in India. This paper aims to provide an overview of a methodology that was developed for designing and assessing the feasibility of a hybrid solar-biomass power plant in Gujarat.

The methodology described is a combination of engineering and business management studies used to evaluate and design solar thermal collectors for specific applications and locations. For the scenario of a hybrid plant, the methodology involved: the analytical hierarchy process, for solar thermal technology selection; a cost-exergy approach, for design optimisation; quality function deployment, for designing and evaluating a novel collector – termed the elevation linear Fresnel reflector (ELFR); and case study simulations, for analysing alternative hybrid plant configurations.

The paper recommended that for a hybrid plant in Gujarat, a linear Fresnel reflector of 14,000 m2 aperture is integrated with a 3 tonne per hour biomass boiler, generating 815 MWh per annum of electricity for nearby villages and 12,450 tonnes of ice per annum for local fisheries and food industries. However, at the expense of a 0.3 ¢/kWh increase in levelised energy costs, the ELFR can increase savings of biomass (100 t/a) and land (9 ha/a).

The research reviewed in this paper is primarily theoretical and further work will need to be undertaken to specify plant details such as piping layout, pump sizing and structure, and assess plant performance during real operational conditions.

The paper considers the methodology adopted proved to be a powerful tool for integrating technology selection, optimisation, design and evaluation and promotes interdisciplinary methods for improving sustainable engineering design and energy management.