Search results

As a new type of ultrasonic transducer with significant advantages, capacitive micromachined ultrasonic transducer (CMUT) has good application prospect. The reception characteristic of the CMUT is one of the important factors determining the application effect. This paper aims to study the reception characteristics of CMUT.

In this paper, the state equation is deduced and the analysis model is established in SIMULINK environment based on the lumped parameter system model of the CMUT cell. Based on this analysis model, the influencing factors of CMUT reception characteristics are studied and investigated, and the time-domain and frequency-domain characteristics are investigated in detail.

The analysis results show that parameters directly affect the reception characteristics of the CMUT, such as direct current (DC) bias voltage, input sound pressure amplitude and frequency. At the same time, the measurement system is built and the reception characteristics are verified.

This paper provides an effective method for rapid analyzing the reception characteristics of CMUT. These results provide an important theoretical basis and reference for further optimization of CMUT structure design, and lay a good foundation for the practical application measurement.

Detection of hidden defects of aluminum alloy plate with damping coating is a challenging problem. At present, only a few non-destructive testing methods exist to address this engineering problem. Without the restriction of skin effect, remote field eddy current (RFEC) overcomes the interference caused by the damping coating. The RFEC, which has potential advantages for detecting the hidden defects of aluminum plate with damping coating, can penetrate the metal plate to detect buried depth defects. This study aims to test how thick the RFEC sensor can penetrate the metal plate to detect the buried defects.

The magnetic field distribution characteristics are analyzed, the magnetic field intensity distribution is calculated, and the structure and parameters of the coil, magnetic circuit and shielding damping are determined through the two- and three-dimensional finite element simulation methods. Optimal excitation frequency is obtained, and the distance between the excitation coil and detection coil is determined by analyzing the relationship between excitation frequency and remote field points.

Simulation and experimental results verify the feasibility of applying the RFEC detection technology in detecting the hidden defects of aluminum alloy plate with damping coating.

In this paper, the RFEC testing model of hidden defects in aluminum plate sample with damping coating is established by using the finite element method.

The topic of impulsive buying has been studied by researchers for nearly 70 years and made a large number of valuable discoveries. However, most of the existing research studies focused on the impulse buying behavior in the context of single person shopping from the perspective of individuals and lack of research on impulse buying behavior in the context of shopping with others from the perspective of communities. Given that consumers' decision-making in the presence of others is significantly different from that when they are alone, it is necessary to probe into the internal mechanism of impulse purchase behavior in the context of shopping with others.

In total three experiments were used to test the hypothesis. Study 1 examines the differences in the motivation of impulsive desire among consumers with different impulsive traits. A total of 240 undergraduates were recruited to participate in the study. The purpose of study 2 is to examine the effect of external attribution on consumer guilt, which leads to the failure of self-control. A total of 256 undergraduate students participated in the study 2. The purpose of study 3 was to test the moderating effect of the intensity of ties on the impact of goal on impulse purchase intention. A total of 240 subjects participated in study 3.

When shopping with companions, consumers with different impulse traits have different initial impulses in the face of temptation, but they may have a similar higher willingness to buy on impulse. There are two reasons: on the one hand, consumers with high-impulsive traits produce a higher desire to buy on impulse driven by hedonistic motivation. In contrast, consumers with low-impulse traits will also have a higher impulse purchase desire driven by prosocial motivation. On the other hand, external attribution can lead to the failure of self-control and impulse purchase behavior. However, the above effects only occur when there is a strong connection between consumers.

First, this paper simulates the phenomenon of impulse purchase in the relational situation through experimental methods; if the research based on the real consumption scenario can be carried out, the research results will be more convincing. Second, whether there are other intermediary mechanisms, such as whether external attribution can affect consumers' self-control through perceived social support, need to be further tested. Finally, it is also necessary to examine the role of other regulatory variables, such as consumers' sense of power, the type of self-construct, etc., and these research clues will further enrich the research on impulsive buying in the context of relationship.

First, businesses can launch more accurate marketing strategies for consumers who are shopping together, find ways to reduce consumers' attention to their own responsibility or fault and guide them to conduct external attribution to their impulsive consumption behavior. The findings also have implications for consumers to control their own impulse purchase behavior. In addition, the results of this study can provide new insights into the government to prevent social crisis and carry out consumer education.

The key contribution of the current research is that, unlike existing studies that focus on the exploration of impulsive buying in the context of single person shopping, this study explores the internal mechanism and causal process on how consumers' impulsive buying behavior occurs when shopping with others. The authors further make a contribution to a self-control theory by demonstrating that external attribution has a negative effect on self-control in relational situations. Finally, this study also finds that the intensity of ties can moderate the impacts of focus goals on impulsive buying behavior.

In order to discover a new adsorbent that can be used to purify dye wastewater in the textile and apparel industry, a novel type of graphene oxide/gluten composite material using an improved acid bath coagulation method was synthesized, which can remove methylene blue in an aqueous environment.

After experimentally compounding different ratios of graphene oxide and gluten, the graphene oxide/gluten composite material with 20% graphene oxide content and superlative adsorption effect was chosen. The synthesized material was characterized by different techniques such as FT-IR and SEM, indicating the microstructure of the material and the success of the composite. Various factors were considered, namely, the influence of temperature, dosage, pH and contact time. The isotherms, kinetics and thermodynamic parameters were successively discussed.

The qmax value of 214.29 mg/g of the material was higher compared to the general sorbent, thus, the graphene oxide/gluten composite material was a suitable sorbent for methylene blue removal. Overall, the graphene oxide/gluten composite material can be considered as an effectual and prospective adsorbent to remove methylene blue in the textile and apparel industrial effluent.

Graphene oxide is a potentially excellent sorbent. However, the high dispersibility of GO is detrimental to adsorption, it disperses rapidly in an aqueous solution making separation and recovery difficult. The high load capacity and recyclability of gluten as a colloid make it a suitable carrier for fixing GO. Studies on the combination of GO and GT into composite adsorption material and for the removal of dyes from dyeing wastewater have not been reported. The composite material research on GO and GT can provide new ideas for the research of these kinds of materials and contribute to its wider and convenient application in wastewater treatment.

The purpose of this paper is to study the effect of vapor assembly sequence and assembly temperature on the corrosion protection of the complex silane films Al alloy. The performance and application range of silane films are enhanced.

The complex silane films were successfully prepared on the surface of aluminum alloy using via vapor phase assembly of 1,2,3-benzotriazole (BTA) and dodecyltrimethoxysilanes (DTMS). The protection of the assembly films against corrosion of Al alloy is investigated by the electrochemical measurements and the alkaline solution accelerated corrosion test. Thickness and hydrophobicity of the complex films are studied using ellipsometric spectroscopy and contact angle tests.

It shows that the anti-corrosion ability of the complex films is overall superior to that of the single-component assembled films. DTMS-BTA films have larger thickness and best anti-corrosion ability. The alkyl chains in DTMS have better compatibility with BTA molecules. The rigid BTA molecule can permeate into the long alkyl chain of DTMS as fillers and improve the barrier properties of the complex films.

In this paper, a green and efficient method of vapor phase assembly is proposed to rust prevention during manufacture of Al alloy workpiece.

The purpose of this paper is to purify the wastewater in the garment industry.

The preparation of the calcium alginate (CA)/activated carbon (AC) composite membrane was achieved by vacuum freeze-drying and the cross-linking reaction between sodium alginate and CaCl₂. Effective parameters in the methylene blue (MB) adsorption such as temperature, dose, contact time and pH were discussed. The adsorption properties of the composite membrane were investigated by isotherm, kinetics and thermodynamic analysis. The adsorption equilibrium data were described by the adsorption isotherm Langmuir model and the Freundlich model. The pseudo-first-order, pseudo-second-order and intra-particle diffusion equations were selected to evaluate the kinetics. The thermodynamic study described that the adsorption reaction was spontaneous and exothermic.

The AC/CA membrane is an efficient and powerful adsorbent to remove MB in printing and dyeing wastewater, and provides a new idea for the selection of adsorption materials for industrial printing and dyeing wastewater.

The composite membrane research on CA and AC can provide new ideas for the research of these kinds of materials.

The paper contributes to its wider and convenientapplication in wastewater treatment.

Studies on the combination of CA and AC into adsorption membranes and for the removal of dyes from printing and dyeing wastewater have not been reported. A novel composite material is provided for treatment dyeing wastewater in garment production. The composite membrane research on CA and AC can provide new ideas for the research of these kinds of materials and contribute to its wider and convenient application in wastewater treatment.

The purpose of this paper is to propose a wheel/rail mixed lubrication model to study the water lubrication behavior of wheel/rail contact interface.

The numerical simulation method is applied in this paper. A deterministic mixed lubrication model considering surface roughness and transient state is established. The quasi-system numerical and finite difference method are used for numerical solution. The model is verified by comparing with the experimental data in the literature under the same conditions.

Under wet conditions, the change of train speed will change the lubrication state of the wheel/rail contact interface. With an increasing speed, the average film thickness and the film thickness ratio increase, while the adhesion coefficient, the contact load ratio and the contact area ratio decrease. When the creep ratio increases from 0% to 0.5%, the wheel/rail adhesion coefficient and subsurface stress increase sharply. With the increase of axle load, the average film thickness decreases and the adhesion coefficient increases.

This paper aims to improve the mixed lubrication theory by analyzing the characteristics of wheel/rail friction and lubrication, so as to provide some guidance and theory for train driving behavior.

Using the deterministic model, the lubrication state of the wheel/rail contact interface affected by various external factors and the adhesion behavior of wheel/rail progressive process from boundary lubrication to mixed lubrication are studied.

In view of the defects of glued wood beams, a new composite member – reconstituted bamboo board reinforced glued wood beams is proposed to improve the bearing capacity of glued wood beams.

The bending test studied the ordinary glulam beams and the reinforced glulam beams with different layer numbers and different layer thicknesses by comparing with six kinds of glulam beams strengthened with bamboo scrimber and one kind of ordinary glulam beams and used the method of third-point stepwise loading on the glulam beams strengthened with bamboo scrimber.

The bamboo scrimber improved the bending behavior of the ordinary glulam beams. The 10 mm bamboo scrimber layer can meet the requirements of the maximum ultimate bending capacity and minimize the defects. So 10 mm bamboo scrimber layer was the optimal thickness. During the loading process, the strain change of the normal section of the reconstituted bamboo board reinforced glued wood beam basically conforms to the plane section assumption.

The bending rigidities of the glulam beams strengthened with bamboo scrimber increased up to 28.25%, 8.53% and 76.67%, and the ultimate bending capacity increased from 83.44% to 99.34% with the increase of the bamboo scrimber plate layers (the replacement rate). The ultimate bending capacities and the bending rigidities of the glulam beams strengthened with bamboo scrimber increased to 52.32%∼60.18% and 90.07%∼99.34% with the changing of the bamboo scrimber thicknesses from 7.1 mm to 25 mm.

Because of the small size and high integration of capacitive micromachined ultrasonic transducer (CMUT) component, it can be made into large-scale array, but this lead to high hardware complexity, so the purpose of this paper is to use less elements to achieve better imaging results. In this research, an optimized sparse array is studied, which can suppress the side lobe and reduce the imaging artifacts compared with the equispaced sparse array with the same number of elements.

Genetic algorithm is used to sparse the CMUT linear array, and Kaiser window apodization is added to reduce imaging artifacts, the beam pattern and peak-to-side lobe ratio are calculated, point targets imaging comparisons are performed. Furthermore, a 256-elements CMUT linear array is used to carry out the imaging experiment of embedded mass and forearm blood vessel, and the imaging results are compared quantitatively.

Through the imaging comparison of embedded mass and forearm blood vessel, the feasibility of optimized sparse array of CMUT is verified, and the purpose of reducing the hardware complexity is achieved.

This research provides a basis for the large-scale CMUT array to reduce the hardware complexity and the amount of calculation. At present, the CMUT array has been used in medical ultrasound imaging and has huge market potential.

This paper aims to develop a new magnetorheological polishing (MRP) device with roller and investigate the polishing mechanism of MRP fluids using this new device.

The principle of MRP process with roller is discussed, and then the structure of the polishing device is designed in detail. The polishing experiments of K9 glass are carried out using MRP device with roller.

A series of tests are performed to evaluate the effect of the excitation gaps, working gap and polishing time on the polishing characteristics, and the optimized polishing parameters can be obtained. The surface roughness Ra of the sample is reduced from 359 to 38 nm under optimized polishing parameters.

MRP method with roller is proposed in this paper, and the MRP device with roller can reduce the surface roughness Ra significantly. After being polished, the circular ring-shaped polishing belt disappears on the workpiece surface, which means it has great potential for polishing.