Search results

The low resistance against penetration of water, oxygen and the other corrosive ions through the paths of coating is one the most important problems. So, protective properties of coating such as polyester must be promoted. Recently, the use of nanoparticles in the matrix of polymer coating to increase their protection and mechanical properties has been prospering greatly. The purpose of this study is to improve the corrosion resistance of the polyester powder coating with ZnO nanoparticles. The ZnO nanoparticles have been synthesized by hydrothermal method in a microwave. Using polyester – ZnO nanocomposite coating as powder – combining them by ball milling process and coating them by electrostatic process are innovative ideas and have not been used before it.

Polyester powder as the matrix and ZnO nanoparticles as reinforcing were combined in three different weight percentage (0.5, 1, 2 Wt.%), and they formed polymer nanocomposite by ball milling process. Then, the fabricated nanocomposite powder was applied to the surface of carbon steel using an electrostatic device, and then the coatings were cured in the furnace. The morphology of synthesized zinc oxide nanoparticles was investigated by transmission electron microscope. Also, the morphology of polyester powder and fabricated coatings was studied by scanning electron microscope. The effects of zinc oxide nanoparticles on the corrosion resistance of coated samples were studied by electrochemical impedance spectroscopy (EIS) test at various times (1-90 days) of immersion in 3.5 per cent NaCl electrolyte.

Scanning electron microscopy (SEM) results reveal that there are no obvious crack and defects in the nanocomposite coatings. In contrast, the pure polyester coatings having many cracks and pores in their structure. According to the EIS results, the corrosion resistance of nanocomposite coating compared to pure coating is higher. The value obtained from EIS test show that corrosion resistance for coating that contains 1 Wt.% nanoparticle was 32,150,000 (Ωcm²), which was six times bigger than that of pure coating. In addition to providing a barrier against diffusion of electrolyte, ZnO nanoparticles act as a corrosion inhibitor and, thus, increases the corrosion resistance. The corrosion resistance of coating containing 0.5 Wt.% nanoparticles was lower as compared to that of 1 Wt.% nanoparticles. The low content of nanoparticles caused partial covering of the porosity of coating which in turn leads to provide weaker barrier properties. The increase in quantity of nanoparticles from 1 to 2 Wt.% also caused a decrease in corrosion resistance which is attributed to the agglomeration of nanoparticles.

The results of this study indicated the significant effect of ZnO nanoparticles on the protective performance and corrosion resistance of the polyester powder coating. Evaluation of coating surface and interface with SEM technique revealed that nanocomposite coating compared with pure polyester coating provided a coating with lower number of pores and with higher quality. The EIS measurements represented that polymeric coating that contains nanoparticles compared to pure coating provides a better corrosion resistance. In addition to providing a barrier against diffusion of electrolyte, ZnO nanoparticles act as a corrosion inhibitor and thus increase the corrosion resistance. The corrosion resistance of coating containing 0.5 Wt.% nanoparticles was lower as compared to that containing 1Wt.% nanoparticles. The low content of nanoparticles caused partial covering of the porosity of coating which in turn leads to provide weaker barrier properties. The increase in quantity of nanoparticles from 1 to 2 Wt.% also caused a decrease in corrosion resistance which is attributed to the agglomeration of nanoparticles.

Plasma electrolytic saturation (PES) treatments were applied on the surface of AISI H13 steel and corrosion resistance of the treated samples was investigated using electrochemical test methods. The aim was to obtain optimal corrosion resistance of the differently treated samples.

Nitrocarburized and boride layers were produced on AISI H13 steel by the means of the PES technique. Different experimental parameters during each treatment provided different microstructural and electrochemical properties. The techniques used in the present investigation included X‐ray diffraction, SEM, potentiodynamic polarization measurements and electrochemical impedance spectroscopy (EIS).

The plasma electrolytic nitrocarburising coating was characterized by lower integrity than a PEB coating. All PES coated steels had a noble electrochemical behavior compared to the untreated steel. Different nano‐structures and morphologies obtained by different experimental parameters produced different electrochemical behaviors.

The results obtained in this research into PES techniques can be used wherever good corrosion resistance with the highest efficiency is required.

The speed of treatment by plasma electrolytic saturation techniques makes this method very suitable for industrial production of components.

The purpose of this paper is to investigate the effect of thermal treatment at low partial pressure of oxygen on electrochemical corrosion resistance of Ti‐47Al‐2Cr (at %) intermetallic, known as γ‐TiAl alloy.

The surfaces of the samples were modified by thermal treatment at different temperatures in N₂ gas flow for an hour. Characterization of the modified surface layers was carried out by microscopic examinations, hardness and roughness tests, and X‐ray diffraction analyses. Potentiodynamic polarization was used to evaluate the corrosion performance of γ‐TiAl in Ringer's solution.

The results indicated that the alloy treated at 950 °C had the optimum corrosion resistance, which can be attributed to the formation of an oxide layer by the surface thermal treatment and increase of the passive layer thickness.

Low corrosion rate (CR), high pitting potential (Epit), and more noble corrosion potential (Ecorr) make it possible for γ‐TiAl to be considered as a candidate for biomedical applications.

The treatment described in the paper is a novel method for surface modification of this type of alloy and results showed that it was an effective treatment and that the corrosion resistance improved remarkably.