Multidiscipline Modeling in Materials and Structures: Volume 15 Issue 6

Optimization of Ti-6Al-4V/AISI304 diffusion bonding process parameters using RSM and PSO algorithm

A. Arun Negemiya, S. Rajakumar, V. Balasubramanian

The purpose of this paper is to develop an empirical relationship for predicting the strength of titanium to austenitic stainless steel fabricated by diffusion bonding (DB…

Hygro-thermally induced stress intensity factor of an edge crack piezo laminated composite plate

Achchhe Lal, Khushbu Jain

The purpose of this paper is to evaluate hygro-thermo-mechanically induced normalized stress intensity factor (NSIF) of an edge crack symmetric angle-ply piezo laminated composite…

Impact of generalized Fourier’s law and Fick’s law for MHD flow of Ag‒H2O and TiO2‒H2O nanomaterials

Sumit Gupta, Devendra Kumar, Jagdev Singh, Sandeep Gupta

The purpose of this paper is to investigate the effect of inclined magnetic field, variable viscosity and Cattaneo–Christov heat and mass flux theories on the steady MHD free…

Dynamical analysis of hydromagnetic Brownian and thermophoresis effects of squeezing Eyring–Powell nanofluid flow with variable thermal conductivity and chemical reaction

Hammed Abiodun Ogunseye, Sulyman Olakunle Salawu, Yusuf Olatunji Tijani, Mustapha Riliwan, Precious Sibanda

The purpose of this paper is to investigate the dynamical behavior of heat and mass transfer of non-Newtonian nanofluid flow through parallel horizontal sheet with heat-dependent…

Numerical investigation of high pressure turbine blade tip-shaping effects on the aerothermal and dynamic performance

Fujuan Tong, Wenxuan Gou, Lei Li, Zhufeng Yue, Wenjing Gao, Honglin Li

In order to improve the engine reliability and efficiency, an effective way is to reform the turbine blade tip conformation. The paper aims to discuss this issue.

Solving two-dimensional non-linear quadratic integral equations of fractional order via operational matrix method

Farshid Mirzaee, Sahar Alipour

The purpose of this paper is to develop a new method based on operational matrices of two-dimensional delta functions for solving two-dimensional nonlinear quadratic integral…

Static buckling and vibration analysis of continuously graded ceramic-metal beams using a refined higher order shear deformation theory

Ahmed Bekhadda, Ismail Bensaid, Abdelmadjid Cheikh, Bachir Kerboua

The purpose of this paper is to study the static buckling and free vibration of continuously graded ceramic-metal beams by employing a refined higher-order shear deformation…

Heat transport in the convective Casson fluid flow with homogeneous‒heterogeneous reactions in Darcy‒Forchheimer medium

S. Bilal, Muhammad Sohail, Rahila Naz

The purpose of this paper is to highlight the studies of momentum and transmission of heat on mixed convection boundary layer Darcy‒Forchheimer flow of Casson liquid over a linear…

Predicting crack in a beam-like structure through an over fitting verified regression model

Sasanka Choudhury, Dhirendra Nath Thatoi, Jhalak Hota, Suman Sau, Mohan D. Rao

The purpose of this paper is to identify the crack in beam-like structures before the complete failure or damage occurs to the structure. The beam-like structure plays an…

Vibration analysis of transversely isotropic hollow cylinder considering three different theories using the matrix Frobenius method

Siddhartha Biswas

The purpose of this paper is to deal with the three-dimensional analysis of free vibrations in a stress-free and rigidly fixed homogeneous transversely isotropic hollow cylinder…

Thermoviscoelastic response of an axially loaded beam under laser excitation and resting on Winkler’s foundation

Ahmed E. Abouelregal, Ashraf M. Zenkour

The purpose of this paper is to investigate the response of viscoelastic beam resting on a Winkler’s foundation and subjected to an axial initial stress, thermal load and an…

Effects of shot sleeve filling in HPDC machine

Korti Mohammed Choukri, Korti Abdel Illah Nabil, Abboudi Said

High-pressure die casting is one of the manufacturing techniques used for the rational mass production of metal parts. Due to the high velocity of the molten metal during the…

Dynamic analysis of two collinear permeable Mode-I cracks in piezoelectric materials based on non-local piezoelectricity theory

Haitao Liu, Shuai Zhu

Based on the non-local piezoelectricity theory, this paper is concerned with two collinear permeable Mode-I cracks in piezoelectric materials subjected to the harmonic stress…

Experimental and computational simulations for the effect of new Arylfuranylnicotinamidine derivatives against degradation of carbon steel in acid solutions

Abdelaziz S. Fouda, Mohamed A. Ismail, Rabab M. Abou-shahba, Walaa A. Hussein, Esraa S. El-habab, Ashraf S. Abousalem

The purpose of this paper is to investigate three Arylfuranylnicotinamidine derivatives against corrosion of carbon steel (C-steel) in 1.0 M HCl by chemical and electrochemical…

Performance evaluation of cryogenically treated wires during wire electric discharge machining of AISI D3 die tool steel under different cutting environments

Husandeep Sharma, Khushdeep Goyal, Sunil Kumar

Tool steel (AISI D3) is a preferred material for industrial usage. Some of the typical applications of D3 tool steel are blanking and forming dies, forming rolls, press tools and…

Spot lap joining of AA5052 to AISI 1006 by aluminium extrusion via friction forming technique

Sabah Khammass Hussein, Isam Tareq Abdullah, Abbas Khammas Hussein

The purpose of this paper is to join AA5052 to AISI 1006 steel sheets using the spot friction forming technique.

Stress intensity factors of multiple axisymmetric interface cracks in an isotropic layer with FGM coating under torsional loading

Arash Tavakoli, M. Pourseifi, Sara Rezaei

The purpose of this paper is to provide a theoretical analysis of the fracture behavior of multiple axisymmetric interface cracks between a homogeneous isotropic layer and its…

Porous ceramic foam loading titanium dioxide for photocatalytic degradation of the methyl orange solution

Y.J. Guo, W. Cheng, P.S. Liu

The purpose of this paper is to provide an investigation on a new kind of photocatalytic material, namely, the porous ceramic foam loading titanium dioxide, which can make an…